Siemens SIMODRIVE 611 universal Function Manual page 917

04.05
Control board
1-axis for encoders with sin/cos 1Vpp,
1-36
1-axis for resolvers, 1-32, 1-36
2-axis for encoders with sin/cos 1Vpp,
1-32, 1-35
2-axis for encoders with TTL signals
(from SW 8.1), 1-32
2-axis for resolvers, 1-32, 1-35
2-axis for SINUMERIK 802D, 1-43
Elements on the front panel, 1-37
Memory module, 1-26
Control board front panel, 1-37
Controller enable, 6-473
Couplings (from SW 3.3), 6-431
Equalization controller (from SW 7.1),
6-467
Torque setpoint coupling via PROFIBUS
(from SW 4.1), 6-461
with queue function (being prepared),
6-446
CP xxxx, 3-110, 3-113
Current regulator, 6-332
Adaptation, 4-162
Optimization, 6-336
D
Data Exchange Broadcast (from SW 4.1),
5-314
Data medium, 1-32
Data transfer
Consistent, 5-283, 5-284
Inconsistent, 5-283, 5-284
DAU, 2-74, 7-723
DC link, 2-70
Declaration of Conformity, D-903, D-907
Diagnostics
Actual traversing block, 6-425
LED on the control board, 7-627
LED on the optional PROFIBUS module,
5-289
of the movement status, 6-388
Operating display, 4-135
Parameters for, 4-134
Using the 7–segment display, 7-624
Digital inputs
for control board, 2-76, 6-474
for the optional TERMINAL module, 2-79,
6-526
E Siemens AG 2005 All Rights Reserved
SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition
Digital outputs
for control board, 2-77, 6-498
for the optional TERMINAL module, 2-79,
6-526
if all do not "function", 2-77, 2-79
Dimension system, 6-365
Dimension system grid (MSR), 6-361, 6-365
Direct measuring system, A-889
Direct measuring system (from SW 3.3),
4-193
Direction adaptation, 6-381
Display and operator unit, 1-38
Example: Changing a parameter value,
3-95
Display in cyclic operation, 4-119
Display unit
Alarm mode, 3-89
Hexadecimal values, 3-94
Parameterizing mode, 3-89, 3-90
Power–on mode, 3-89
Distancecoded reference marks
nset mode (from SW 4.1), 6-352
pos mode (from SW 8.3), 6-395
Drive configuration, 3-102
Drive group, 1-28
Drive inactive, 4-139
Drive number for RS485, 3-104
DSC, 6-603
DSR, 6-603
Dynamic monitoring of following errors,
6-382
Dynamic servo control, 6-603
E
EC Declaration of Conformity, D-903, D-907
Electronic handwheel (SW 8.1 and higher)
Angular incremental encoder – direction-
dependent, 6-568
Angular incremental encoder handwheel
evaluation, 6-567
EMC Design Guidelines, 2-66
Encoder adaptation, 6-354
Encoder code, 4-138, A-885
Encoder connection, 2-75
Encoder interface (from SW 3.1), 1-51,
1-57, 5-243
Encoder limit frequency, 1-48, 2-75
Encoders, 1-26, A-885
Ends of conductors, 2-69
E Index
E
E-917