Riso ComColor X1 series Technical Manual page 643

Test Modes
Data Editing (D)
No. Process Name
HCF Prior Roller Assist
3763
Speed Setting
HCF Middle Feed Roller
3765
Assist Speed Setting
3768 HCF Serial Number Setting
HCF U/L Limit Sensor
3769 Simultaneous Detection
Warning
HCF Custom Paper Size
3771
Upper Limit Detection
HCF Envelope Upper Limit
3772
Detection
3776 HCF P-F Tray Motor Setting
HCF Nip Release Motor
3882
Release Position
HCF Nip Release Motor Nip
3883
Position
Data Editing (D)
No. Process Name
HCF Paper Buckle
7675
(Standard-Long)
HCF Paper Buckle
7676
(Standard-Short)
HCF Paper Buckle (Thin-
7677
Long)
HCF Paper Buckle (Thin-
7678
Short)
HCF Upper Limit Position
7722
(Standard)
HCF Paper Feed Timing
7724
(Standard)
HCF P-F Assist Control
7725
(Standard)
HCF P-F Assist Start Timing
7726
(Standard)
HCF P-F Assist End Timing
7727
(Standard)
Rev.1.00
OPTIONS / High Capacity Feeder
Default Unit/Range
977 800-1200
977 800-1200
0 0-32500
0: Warning disable
1
1: Warning enable
HCF equipped with two type custom paper upper surface detection. These are
the bearing detection and the scraper detection.
HCF system automatically switch detection method by kind of paper.
0
0: Disable
1: Forcing with bearing detection
2: Forcing with scraper detection
HCF equipped with two type envelope upper surface detection. These are the
bearing detection and the scraper detection.
HCF system automatically switch detection method by kind of paper.
0 Default setting of envelope is the scraper detection.
0: Disable
1: Forcing with bearing detection
2: Forcing with scraper detection
In order to improve the jam recovery of small size paper when the registration
sensor detected non-arrival jam.
0 0: Display the error after the paper is transported
1: Stops the HCF Registration Motor and the HCF P-F Tray Motor together,
when error occur
(-1000 - 1000)
0
pulse
(-1000 - 1000)
0
pulse
OPTIONS / High Capacity Feeder
Default Unit/Range
6 (-4 -15)mm
0 (-4 -15)mm
6 (-4 -15)mm
4 (-4 -15)mm
Sets the upper limit position of HCF unit. (Standard paper)
1
0: Top 1: Middle 2: Bottom
0 (-100 - 100)ms
0: OFF
1
1: ON
0 (-100 - 100)ms
0 0-200ms
[ 16-100 ]
Description
Sets the assist speed of the prior roller against the
registration roller transport speed.
If set the prior roller assist speed slower than the registration
roller, paper buckle will decrease.
Sets the assist speed of the middle feed roller against the
registration roller transport speed.
If set the prior roller assist speed slower than the registration
roller, paper buckle will decrease.
This is effective if the paper size is larger than the distance
between the registratio roller and the 3rd middle feed roller.
Set HCF serial number.
If choose disable on this test mode, even though the HCF
P-F tray upper limit sensor and the HCF P-F tray lower
limit sensor detect when starts printing, there is no warning
display.
Corrects release position of the Nip Release Mechanism.
Corrects nip position of the Nip Release Mechanism.
Description
Sets the amount of slackness of HCF unit. (Standard & long
paper)
Sets the amount of slackness of HCF unit. (Standard &
short paper)
Sets the amount of slackness of HCF unit. (Thin & long
paper)
Sets the amount of slackness of HCF unit. (Thin & short
paper)
Sets the paper feed timing of HCF unit. (Standard paper)
Select paper feed assist control of the HCF unit. (Standard)
Sets the paper feed assist start timing of HCF unit.
(Standard paper)
Sets the paper feed assist end timing of HCF unit. (Standard
paper)