Riso ComColor X1 series Technical Manual page 618

Data Editing (D)
No. Process Name
4802 Punch Registration Timing A4S
4808 Booklet Add Tamping Setting 1
Booklet Staple Hold Add Tamping
4809
Setting 1
4810 Booklet Add Tamping Number Setting 1
4811 Enable Stacker Height Sensor 1
4815 Paddle Support Set Width 2
4816 Z-Fold 11X17 Setting
4817 Sub Paddle Timing B5L
4820 Punch Timing
4821 Stacker Tray Timing
4822 Stacker Tray Top Width
4823 Stacker Tray Top Length
4824 Stacker Tray Max Width
4825 Stacker Tray Min Length
4826 Booklet End Guide Calibration Setting
4827 Stacker Tray Eject A3
4830 Compile Paddle UP Timing (Short)
4831 Compile Paddle UP Timing (Long)
4832 Disable 2/3 Hole Puncher A-CHANG
OPTIONS / Finisher
Default Unit/Range
8 1-255
0 0-2
0 0-10
6 0-25
Select the sensor for adjusting Stacker tray height.
0 0: Not permitted (Use Stacker Height Sensor 2)
1: Permitted (Use Stacker Height Sensor 1)
235 204-254
10 1-20sheet
1 1-48
0 0-65535time
0 0-255copy
0 0-65535
0 0-65535
0 0-65535
0 0-65535
60 30-255
0: Not ejected
0
1: Ejected
90 4-255
120 4-255
0: 3-hole puncher
1 1: 2/3 hole
puncher
[ 16-75 ]
Description
With A4SEF and LET SEF paper and 2-hole
punching, adjusts the time until punch side
registration detection starts.
Set additional tamping times on normal booklet
tamping. (Except IOT:Pinot)
Set additional tamping times on booklet staple
hold. (Except IOT:Pinot)
Set specifi ed number on additional tamping
times. (Except IOT:Pinot)
At normal tamping, At fi nal tamping, At staple
hold, At staple front fold position (Larger than
B4SEF)
Paper width threshold of implementing the
behavior support paddle.
No action make if the paper width is less than
235mm.
Converted sheet quantity for one z-fold sheet
(A3 or 1111x17 ).
For standard paper, 182 mm or shorter in the
direction of transfer and 257 mm or narrower
in width (smaller than B5LEF),
adjusts the timing of sub paddle support
operation. (1=2.5ms)
Record of the number of punches used to
detect when the punch container is full.
Quantity of stapled copies ejected in the
stacker tray.
Width of highest sheet in the stacking tray.
0x0000 to 0xFFFF (1=0.1mm)
Length of highest sheet in the stacking tray.
0x0000 to 0xFFFF (1=0.1mm)
Width of largest sheet in the stacking tray.
0x0000 to 0xFFFF (1=0.1mm)
Length of largest sheet in the stacking tray.
0x0000 to 0xFFFF (1=0.1mm)
Specifi es the amount for raising and lowering
the end guide when ejecting small booklets
to prevent mis-registration by these additional
raising and lowering actions.
Valid when 763-425=1
(1=0.1mm)
Indicates the ejection status of z-fold A3SEF
and 11x17 SEF sheets ejected in the stacking
tray.
Specifi es the timing to start raising and
lowering the compile paddle for each fi ve
sheets beginning with the 60th sheet. (When
the paper is shorter than 330 mm.)
(1=5ms)
Specifi es the timing to start raising and
lowering the compile paddle for each fi ve
sheets beginning with the 60th sheet. (When
the paper is 330 mm or longer.)
(1=5ms)
Notifi cation to IOT when 2/3-hole puncher is
installed
Test Modes
Rev.1.00