Riso ComColor X1 series Technical Manual page 457

Panel Messages
Type S98: Hardware error
!!System Error!!
Display Reboot by press the Sub Power Key
If recovery has failed, call service.
Clear
Turn OFF the printer. (Turn OFF the printer through sub power key.)
Point Description
0001
The CPU detected a checksum error during CPU-DSP communication.
0002 The CPU detected a timeout error during CPU-DSP communication.
0003
The SS controlling paper transfer control on the CPU side detected a sequence error.
0004
The SS controlling paper transfer control on the DSP side detected a sequence error.
0005 The CPU detected hardware errors in CPU-DSP communication (parity, overrun, or other errors).
0011 The engine PCB version and fi rmware do not match.
0018 1
Watchdog timer actuation caused by system error is detected by the Engine PCB.
0018 2
Watchdog timer actuation other than the cause by system error is detected by the Engine PCB.
0019 1 PCI bus is in parity error when the X3-IP-PCB image processing went in error.
0019 2
PCI bus is in system error when the X3-IP-PCB image processing went in error.
0019 3
PCI bus is in target error when the X3-IP-PCB image processing went in error.
0019 4 PCI bus is in target abort when the X3-IP-PCB image processing went in error.
0019 5 PCI bus is in undefi ned error when the X3-IP-PCB image processing went in error.
0019 6
PCI bus is in undefi ned state when the X3-IP-PCB image processing went in error.
0019 7
PCI bus is in busy state when the X3-IP-PCB image processing went in error.
0019 8 PCI bus is in suspension when the X3-IP-PCB image processing went in error.
PMS-engine communication error 01: Three consecutive code errors were detected in CDB (third checksum
0020
error).
PMS-engine communication error 02: Three consecutive code errors were detected in SDB (third checksum
0021
error).
PMS-engine communication error 03-1: PCI is working fi ne, but no SDB reply, and a timeout error occurred.
0022 1
< Possible X3-IP-PCB connection error.>
PMS-engine communication error 03-2: PCI is not recognized and no SDB reply, and a timeout error
0022 2 occurred.
< Possible faulty the X3-IP-PCB >
PMS-engine communication error 03-3: PCI recognition number is not recognized and no SDB reply, and a
0022 3 timeout error occurred.
< Possible fl at-cable error or software error >
0023 PMS-engine communication error 04: Error involving an undefi ned CDB command code (command error).
PMS-engine communication error 05: Three consecutive code errors in communication involving CDB or
0024
SDB in alternation.
0025
PMS-engine communication error 06: SDB command different from CDB command.
PMS-engine communication error 07: Three consecutive code errors detected in CFH, and DATAREJECT
0026
returned.
0027
PMS-engine communication error 08: Other SDB parameter error, and DATA ERROR returned.
0028 PMS-engine communication error 09: Other CFH parameter error, and DATA ERROR returned.
0029
PMS-engine communication error 10: Nonconsecutive serial numbers detected at CDB reception.
0030
PMS-engine communication error 11: Nonconsecutive serial numbers detected at SDB reception.
PMS-engine communication error 12: Invalid command due to invalid CDB reception sequence (CDB_
0031
INVALIDITY).
PMS-engine communication error 13: SDB EPB size detected to be smaller than the minimum command
0032
EPB size.
To resolve the underlying problem, download FPGA and PMS fi rmware.
Recording data generating PCB (X3-IP-PCB) is not connected to PCI slot.
0036
To resolve the underlying problem, turn the printer off and connect the X3-IP-PCB.
0044 Communication failed between the controller PCB and panel control PCB.
0052 1-9 This error occurs when the hard disk partition is corrupted.
0059
Error detected when checking the size of controller PCB memory (DRAM)
Detected that cooling fan stopped (Controller unit)
0066
Troubleshooting: Check the connection or change the cooling fan.
0067
After touch panel calibration, writing to the fl ash calibration area failed.
0068 After or during touch panel updates, an erasure error occurred in the fl ash update data area.
[ 15-26 ]