Riso ComColor X1 series Technical Manual page 464

Type S99: Software Error
!!System Error!!
Display Reboot by press the Sub Power Key
If recovery has failed, call service.
Clear
Turn OFF the printer. (Turn OFF the printer through sub power key.)
Point Description
0151 1
Error from software bugs related to the sheet queue
0152 1 Abnormal action was detected within the set manager of the engine fi rmware.
During the job deletion, the set manager of the engine fi rmware detected time-out (40 seconds) on any of
0152 2 the following module.
<Print manager>, <Mechanical control>, <Paper transfer control>, <Finisher>
At the stopping of the printing job, the set manager of the engine fi rmware detected time-out (50 seconds)
0152 3 on any of the following module.
<Print manager>, <Mechanical control>, <Paper transfer control>, <Finisher>
At the start of the printing job, the set manager of the engine fi rmware detected time-out (3 minutes) on any
0152 4 of the following module.
<Print manager>, <Mechanical control>, <Paper transfer control>, <Finisher>
At the temporary halt of the auto-cleaning, the set manager of the engine fi rmware detected time-out (50
0152 5
seconds) on any of the following module.
<Print manager>, <Mechanical control>, <Paper transfer control>, <Finisher>
At the start of the printing job, the set manager of the engine fi rmware detected stall on the command from
0152 6
the controller [time-out = 3 minutes] on any of the following module.
<Controller>, <System control module (engine fi rmware)>
When the engine fi rmware received the job deleting command from the controller [time-out = 180 seconds]
0152 7
on any of the following module.
<Print Manager>
0154 1
Parameter error is detected in the X3-IP-PCB.
0154 2
Performance error is detected in the X3-IP-PCB.
0154 3 Parameter error is detected in the X3-IP-PCB at the time of print start.
0154 4
Parameter error is detected in the X3-IP-PCB at the time of sheet reservation.
0154 5
Parameter error is detected in the X3-IP-PCB at the time of image processing start.
0154 6 Transfer ID is detected as [0] at the time the image is processed by the X3-IP-PCB.
0154 7
Image process request was detected by the X3-IP-PCB.
0155 1
Lack of memory area is detected in the system control module in the Engine control PCB.
0155 2
Error related to pre-idle condition is detected in the system control module in the Engine control PCB.
Reply error on the paper transfer during the roller profi le test mode process was detected in the system
0155 3
control module in the Engine control PCB.
0155 4 Transition error was detected in the system control module in the Engine control PCB.
Time-out error on the test mode store/restore was detected in the system control module in the Engine
0155 5
control PCB.
0155 6
Manual store/restore parameter was detected in the system control module in the Engine control PCB.
Transition error on the test mode store/restore was detected in the system control module in the Engine
0155 7
control PCB.
Error on the set cancel process completion was detected in the system control module in the Engine control
0155 8
PCB.
Receive timing error on the STS13 command was detected in the system control module in the Engine
0155 9
control PCB.
0156 1 Set cancel movement time-out was detected in the system control module in the Engine control PCB.
Error in the acknowledgment parameter was detected in the system control module in the Engine control
0156 2
PCB.
0156 3 Error in the initialization movement was detected in the system control module in the Engine control PCB.
0156 4
Error in the wake-up action was detected in the system control module in the Engine control PCB.
Error in the BP de-elevation movement during the paper jam was detected in the system control module in
0156 5
the Engine control PCB.
Unexpected value on the control variable was detected in the system control module in the Engine control
0156 6
PCB.
[ 15-33 ]
Panel Messages