Riso ComColor X1 series Technical Manual page 614

Data Editing (D)
No. Process Name
4729 Z-Fold 50 Sheets Stack
4730 Paper Size Detection Setting
4731 Unstable Paper Quantity Limit 1
4732 Puncher Selection
4733 Punch Side Registration Adjustment 1
4734 Punch Side Registration Adjustment 2
4735 Punch Side Registration Adjustment 3
4736 Punch Clutch ON Timing
4737 Non Punch Clutch Timing
4738 Stack-Tray Down Adjustment
4739 Punch Reserve Adjustment 1
4740 Punch Dust Full Adjustment
4741 Staple Limitation 100
4742 Staple Limitation 50
4743 Rear Staple Position 1
4744 Unstaple Limitation Setting 2
4745 Tamping Home Adjustment
4746 Compile Slow Timing
4747 Eject Mode Setting
OPTIONS / Finisher
Default Unit/Range
0: Prohibited
0
1: Permitted
0: Automatic
0
1: Size input
25 2-50sheet
0: Auto detection
0
1: 4 holes
97 10-170
94 10-170
82 10-170
28 0-40
24 0-40
0: Permitted
0
1: Prohibited
38 8-68
10000 0-65535time
100 50-150sheet
50 25-75sheet
100 50-150sheet
25 2-50sheet
26 0-52pulse
3 1-41pulse
0: Set Eject
0
1: Sheet Eject
[ 16-71 ]
Description
Enables High Stack on Z-fold paper when the
Z-fold High Stack spacer mounted.
However, permitted is selected, TM4958
[Z-FOLD 100SHT STACK] must select
prohibited.
At the same time, need to change limitation
sheet number on following test modes.
TM4797 Z-fold Stacker Tray Limitation
(B4SEF)
TM4800 Z-fold Stacker Tray LImitation (A3)
Modifi es the number of sheets for "unstaple
set eject" for paper longer than 216 mm.
Specifi es puncher settings.
Adjusts the position in the direction of the
punch hole side registration for paper 297 mm
wide. (1=0.125mm)
2/3 Puncher: 203mm ≤ paper width ≤ 285mm
2/4 Puncher: 216mm < paper width ≤ 285mm
Adjusts the position in the direction of the
side registration of these punch holes.
(1=0.125mm)
2/4 Puncher: Adjusts the position in the
direction of the punch hole side registration
when 203 mm < paper width ≤ 216 mm.
(1=0.125mm)
Adjusts the timing of sub paddle clutch
activation when a punch mode buffer sheet
is used and the compile exit sensor is
deactivated (including 15 ms for the fi lter).
(1=2.5mm)
Adjusts the timing of sub paddle clutch
activation when a non-punch mode buffer
sheet is used and the compile exit sensor is
deactivated (including 15 ms for the fi lter).
(1=2.5mm)
Specifi es permission of tray down operation
when cycling down.
In punch mode, adjusts the correction loop
amount for motor reverse skew when the
paper is 216 mm or shorter.
(2/3 Puncher: 203 mm ≤ paper width < 223
mm)
(2/4 Puncher: 216 mm < paper width ≤ 235
mm)
The paper above is excluded.
Frequency of punch waste full detection
Sets a staple limit sheet quantity for 100-sheet
cartridges.
Sets a staple limit sheet quantity for 50-sheet
cartridges.
Adjusts the rear staple position (for other than
A4LEF and A3SEF).
Specifi es the number of sheets for "unstaple
set eject" for paper longer than 216 mm.
Adjusts the tamping home position.
Adjusts the compile exit roller slow-down
timing.
Operation in unstaple eject mode.
Test Modes
Rev.1.00