Riso ComColor X1 series Technical Manual page 625

Test Modes
Data Editing (D)
No. Process Name
4922 C-Fold Solenoid ON 8KTFX
4923 C-Fold Solenoid ON 8KGSO
4924 C-Fold Solenoid ON A3S
4925 C-Fold Solenoid ON 11X17S
4926 C-Fold Solenoid Timing Envelope
4927 Clamp UP Timing NO-P
4928 Clamp UP Timing
4929 Punch Side Adjustment IOT1
4930 Punch Side Adjustment IOT2
4931 Punch Side Adjustment IOT3
4932 Punch Side Adjustment IOT4
4933 Punch Side Adjustment IOT5
4934 Punch Side Adjustment IOT6
4935 Punch Side Adjustment IOT7
Rev.1.00
OPTIONS / Finisher
Default Unit/Range
0-160
0-160
100
80 (AP)
0-160
0-160
0-160
47 42-50ms
49 45-53ms
0 0-24
0 0-24
0 0-24
0 0-24
0 0-24
0 0-24
0 0-24
[ 16-82 ]
Description
When 8KTFX z-folding is used with folder
c-folding, this test mode specifi es the time
when the folder c solenoid is activated after
activation of the folder entrance sensor.
When 8KGCO z-folding is used with folder
c-folding, this test mode specifi es the time
when the folder c solenoid is activated after
activation of the folder entrance sensor.
When A3SEF z-folding is used with folder
c-folding, this test mode specifi es the time
when the folder c solenoid is activated after
activation of the folder entrance sensor.
When 11x17 SEF z-fold is used with folder
c-folding, this test mode specifi es the time
when the folder c solenoid is activated after
activation of the folder entrance sensor.
Specifi es the time for activation of the folder c
solenoid when envelope z/z fold is used.
Changes the timing of raising the eject clamp
in modes without punching. (Affects the eject
clamp motor.)
Changes the time (in ms) after deactivation of
the compiler exit sensor (set fi rst).
Changes the timing of raising the eject clamp
in modes with punching. (Affects the eject
clamp motor.)
Changes the time (in ms) after deactivation of
the compiler exit sensor (set fi rst).
For IOT paper
2/4 hole punching: 216 < width ≤ 230
2/3 hole punching: 203 ≤ width ≤ 223
Under these conditions, adjusts the position
of the punch side. (Adjusts the punch position
toward the front.) (1=0.125mm)
For IOT paper
2/4 hole punching: 230 < width ≤ 250
2/3 hole punching: 223 < width ≤ 241
Subsequently the same as TM04929.
(1=0.125mm)
For IOT paper
2/4 hole punching: 250 < width ≤ 265
2/3 hole punching: 241 < width ≤ 275
Subsequently the same as TM04929.
(1=0.125mm)
For IOT paper
2/4 hole punching: 265 < width ≤ 285
2/3 hole punching: 275 < width ≤ 285
Subsequently the same as TM04929.
(1=0.125mm)
For IOT paper
2/4 hole punching: 285 < width < 297
2/3 hole punching: 285 < width < 297
Subsequently the same as TM04929.
(1=0.125mm)
For IOT paper
2/4 hole punching: width = 297
2/3 hole punching: width = 297
Subsequently the same as TM04929.
(1=0.125mm)
For IOT paper
2/4 hole punching: width ≤ 216 mm
Under these conditions, adjusts the position
of the punch side. (Adjusts the punch position
toward the rear.) (1=0.125mm)