Riso ComColor X1 series Technical Manual page 586

Data Editing (D)
No. Process Name
1893 Roller Profi le ON/OFF
Roller Profi le Gain
1894
Adjustment
Paper Ejectin Option
1895
Connection Setting
1896 Ink Supply ON/OFF
1900 Maintenance Call Setting
Internal Paper Feed Tray
1901
Custom Paper Size Setting
1910 Belt Profi le Data Input 1
1911 Belt Profi le Data Input 2
1912 Belt Profi le Data Input 3
1913 Belt Profi le Data Input 4
1914 Belt Profi le Data Input 5
1915 Belt Profi le Data Input 6
1916 Belt Profi le Data Input 7
1917 Belt Profi le Data Input 8
1918 Belt Profi le Data Input 9
1919 Belt Profi le Data Input 10
1920 Belt Profi le Data Input 11
1921 Belt Profi le Data Input 12
Belt Profi le Check Digit
1922
Input
Roller Profi le Amplitude
1923
Input
1924 Roller Profi le Phase Input
CIS Paper Edge Position
1932
Data Reference Number
CIS Paper Edge Position
1933
Data To Be Excluded
Belt Stain Detection
1934
Frequency
Default Unit/Range
0: Disable
1
1: Enable
80: 80%, 85: 85%, 90: 90%, 95: 95%,
100 100: 100%, 105: 105%, 110: 110%, 115: 115%,
120: 120%
0 ： No Connection
1 ： Perfect Binder
0 2 ： High Capacity
Stacker
3 ： Mail Maker
0: Execute (as
0 needed)
1: Do not execute
0 0–9999sheet
0: Irregular size L
0
1: Irregular size S
0 0-9999
1910-1924 <Refer to photograph on the below>
9 2-10
4 1-9
5 0-100
[ 16-43 ]
ComColor Unit (Series 1000)
Description
Activates or deactivates the roller profi le.
Select correct paper ejection option connected to the printer
unit.
Note: If this selection is not correct, it will not get
communication to the option actually connected.
Specifi es whether ink is supplied.
A comparison value that is compared to the total count for
issuance of maintenance call warnings.
Warnings are issued when the counter is equivalent to this
test setting value x 1000.
When this test setting value is 0, maintenance call warnings
are not issued.
Specifi es what size paper is interpreted as when paper of
irregular size is loaded in internal trays 1–3.
A test for entering items 1–12 of belt profi le data after a
Fourier transform is performed.
An inverse Fourier transform is performed on input values
using test mode 01442 (belt profi le data expansion), after
which values are saved as adjustment data.
A test for entering belt profi le data check digits after a
Fourier transform is performed.
An inverse Fourier transform is performed on input values
using test mode 01442 (belt profi le data expansion), after
which values are saved as adjustment data.
A test for entering the roller profi le amplitude
Input values are saved as adjustment data for test mode
01443 (roller profi le data expansion).
A test for entering the roller profi le phase.
The same note as for above test mode 01923 applies here.
Selects the sample quantity of the prints for the CIS to use
as a data to calculate the paper edge position as detected
by CIS.
This test mode is not to be used in normal operation. Keep
the setting at default value.
Selects the quantity of the sample data to be excluded from
TM_1932 selected number of sample data.
This test mode is not to be used in normal operation. Keep
the setting at default value.
Changes the detection level of the belt stain by CIS. Setting
at [0] will void the belt stain detection.
This test mode is not to be used in normal operation. Keep
the setting at default value.
Test Modes
Rev.1.00