Riso ComColor X1 series Technical Manual page 602

Paper Feed Settings (U1-U5, Light Paper)
Test Mode Number
U1 U2 U3 U4
9729 9775 9821 9867 9913 9960
9730 9776 9822 9868 9914 9961 BELT SPD RATIO
9731 9777 9823 9869 9915 9962 HEAD GAP
9732 9778 9824 9870 9916 9963 VERTICAL POS 1
9733 9779 9825 9871 9917 9964 VERTICAL POS 2
9734 9780 9826 9872 9918 9965
9735 9781 9827 9873 9919 9966 FD S-FNC OFFST
9736 9782 9828 9874 9920 9967 FD E-ROLL SPEED
9737 9783 9829 9875 9921 9968 WING OFFSET
9738 9784 9830 9876 9922 9969 FU EJ ROLL SPD
9739 9785 9831 9877 9923 9970 AS S-FNC OFFST
9740 9786 9832 9878 9924 9971 AS E-FNC OFFST
9741 9787 9833 9879 9925 9972 ENV FLAP MARGN
9742 9788 9834 9880 9926 9973
9743 9789 9835 9881 9927 9974 TR1 SHRT-P BKL
9744 9790 9836 9882 9928 9975 TR2 SHRT-P BKL
9745 9791 9837 9883 9929 9976 TR3 SHRT-P BKL
N/A N/A N/A N/A N/A 9977
Process Name
U5 LP
RE-FEED ARRIVAL
TIMING (U-LONG
SHEET)
CIS SIDE MASK
MODE
RE-FEED ARRIVAL
TIMING (U -
SHORT)
TRNS BELT FAN
SET (LWP)
ComColor Unit (Series 9000)
Default Unit/Range
20 (-50 - 50)ms
1000 950-1020
Specifi es the head gap
0
0: Standard 1: Card 2: Envelopes 1 3: Envelopes 2
0 (-20 - 20)mm
0 (-20 - 20)mm
0: Inactive
1
1: Active
60 (-500 - 500)
Adjusts the FD paper ejection roller speed.
0 0: Standard 1: Heavyweight 2: Lightweight 3: Postcard 4:
Envelopes
0 (-500 - 500)
850 177-1500mm/s
(-40) (-200 - 400)
0 (-300 - 300)
0 0-720
4 (-50 - 50)ms
3 (-10 - 20)mm
4 (-10 - 20)mm
3 (-10 - 20)mm
40 1-100%
[ 16-59 ]
Test Modes
Description
Compensates the re-feed paper arrival
timing. (Long paper = 356 mm or longer.)
Specifi es the belt speed ratio.
This is the transfer belt speed ratio
relative to a registration roller speed of
1. (1=0.1%)
Adjusts secondary scanning position 1.
Adjusts secondary scanning position 2.
Activate or Inactivate the CIS on the
side registration unit to check the paper
width for the Side Margin and Image
Centering.
Adjusts the FD paper ejection fence
offset. (1=0.1mm)
Adjusts the FU paper ejection wing
offset. (1=0.1mm)
Adjusts the FD paper ejection roller
speed.
Adjusts the side paper guide offset of the
auto control stacking tray. (1=0.1mm)
Adjusts the end paper guide offset of the
auto control stacking tray. (1=0.1mm)
Specifi es the length of the overlap width
for envelopes. (1=0.1mm)
Compensates the re-feed paper arrival
timing. (Short paper = 355 mm or
shorter.)
Specifi es the amount of slackness when
short paper is transferred from tray 1.
Specifi es the amount of slackness when
short paper is transferred from tray 2.
Specifi es the amount of slackness when
short paper is transferred from tray 3.
In case of the light weight paper been
selected by the user, and Transfer belt
fan 3 & 4 (middle side) are OFF, and all
other 4 Transfer belt fans are running by
set duty.
To reduce contamination by mist
problem on envelope printing.
Rev.1.00