Riso ComColor X1 series Technical Manual page 582

Data Editing (D)
No. Process Name
1776 Registration Sensor Setting
1780 Tray Descend Duration
1781 Tray Shift Time Set
P-Feed Tray Lowering
1785
operation time setting
Transfer Belt Motor Speed
1786
Adjustment
Paper Elevation Motor
1787
Speed Adjustment
Top Transfer Motor Speed
1788
Adjustment
Switchback Waiting Time
1789
Setting
Switchback Roller Paper
1800
Transfer Amount
Registration Motor Speed
1802
Adjustment
Registration Motor Stopping
1803
Position
1804 Re-Feed Timing Adjustment
Top Edge Sensor 1 Intensity
1807
Adjustment
Top Edge Sensor 2 Intensity
1808
Adjustment
Transfer Belt Suction Fan
1809
Duty Ratio
Top Edge Sensor 1 Paper
1810 Non-Arrival Jam Detect
Timing Adjustment
Paper Elevation IN Sensor
1811 Paper Non-Arrival Jam
Detection Timing Adjustment
Flipper Sensor Paper Non-
1812 Arrival Jam Detection
Timing Adjustment
Top Transfer OUT Sensor
1813 Paper Non-Arrival Jam
Detection Timing Adjustment
Switchback Sensor Paper
1814 Non-Arrival Jam Detection
Timing Adjustment
ComColor Unit (Series 1000)
Default Unit/Range
128 0–255
20 (2 sec) 0-40 (4 sec)
0: Switches to
another paper
feed tray in slow
speed.
0
1: Switches to
another paper
feed tray in high
speed.
10 0-30
0 (-196 - 665)mm/s
(-391 - 1500)mm/
0
s
(-391 - 1500)mm/
0
s
0 (-20 - 20)ms
30 0-100mm
0 (-20 - 20)mm/s
0 (-20 - 20)mm
0 (-50 - 50)ms
128 0–255
128 0–255
100 1-100%
0 (-100 - 100)ms
0 (-100 - 100)ms
0 (-100 - 100)ms
0 (-100 - 100)ms
0 (-100 - 100)ms
[ 16-39 ]
Description
Specifi es the light intensity for the registration sensor.
The higher the value, the brighter the light intensity.
This value is not subject to clearing by a test mode.
Sets the tray descend duration for internal paper feed trays
1,2 and 3.
3 sec. is maximum, so input of over 30 = 30 (3 sec).
Input of 0 = no tray movement.
Selection of slow (default) speed or high speed in switching
to another paper feed tray.
[Refer to the <Tray Selection Per Page function> of the
IS900C Controller.]
Internal trays 1, 2 or 3 must not be pulled out when the
machine is printing from the External tray with the test mode
set to [1] . Mechanical trouble may occur.
Papers of the same size needs to be in the selected trays
for this function to work properly, so the usage of this test
mode is limited.
Use when need to lower the P-F tray when occur vertical
paper feed jam (Vertical paper feed sensor 5 is ON).
(1=0.1s)
Adjusts the transfer belt motor speed.
The setting value of this test mode is added to or subtracted
from the prescribed speed.
Adjusts the paper elevation motor speed.
The setting value of this test mode is added to or subtracted
from the prescribed speed.
Adjusts the upper transfer motor speed.
The setting value of this test mode is added to or subtracted
from the prescribed speed.
Specifi es the wait time when paper is temporarily stopped in
the switchback section before feeding is resumed.
Specifi es the amount of transfer of the switchback roller.
Adjusts registration motor speed relative to the belt speed.
Specifi es the motor stopping position.
Specifi es re-feed timing.
Specifi es the light intensity for top edge sensor 1.
The higher the value, the brighter the light intensity.
Specifi es the light intensity for top edge sensor 2.
The higher the value, the brighter the light intensity.
Specifi es the airfl ow volume of the transfer belt fan,
expressed as a PWM duty ratio.
Specifi es the adjustment value for jams before top edge
sensor 1.
Specifi es the adjustment value for jams before the paper
elevation IN sensor.
Specifi es the adjustment value for jams before the fl ipper
sensor.
Specifi es the adjustment value for jams before the upper
transfer OUT sensor.
Specifi es the adjustment value for jams before the
switchback sensor.
Test Modes
Rev.1.00