Dlp- G86 Verify Express Channel Connections On An Oadm Node With Osc-Csm Cards - Cisco ONS 15454 DWDM Installation And Operation Manual

DLP-G86 Verify Express Channel Connections on an OADM Node with OSC-CSM Cards
DLP-G86 Verify Express Channel Connections on an OADM Node with
OSC-CSM Cards
Purpose
Tools/Equipment
Prerequisite Procedures
Required/As Needed
Onsite/Remote
Security Level
If you are using a tunable laser, set the output power to a nominal value, such as –3 dBm. If not, continue
Step 1
with
Connect the tunable laser transmitter or the TXP_MR_2.5G card DWDM TX port to the LINE RX port
Step 2
of the east OSC-CSM card.
If an OPT-PRE amplifier card is installed on the east side, install a 10-dB bulk attenuator on the
Step 3
COM RX port.
Step 4 Based on the Cisco MetroPlanner site configuration file, tune the tunable laser or TXP_MR_2.5G card
to a wavelength (on the 100-GHz ITU-T grid) that runs on the express path of all AD-xB-xx.x and
AD-xC-xx.x cards on the east-to-west and west-to-east directions. Refer to the tunable laser
manufacturer's documentation or the
Testing" task on page
Complete the
Step 5
OPT-PRE amplifier card installed on the west side.
If AD-xB-xx.x cards are installed on the east side, complete the
Step 6
Output Express Power" task on page 4-47
Note
If AD-xC-xx.x cards are installed on the east side, complete the
Step 7
Output Express Power" task on page 4-47
If AD-xC-xx.x cards are installed on the west side, complete the
Step 8
Output Common Power" task on page 4-48
If AD-xB-xx.x cards are installed on the west side, complete the
Step 9
Output Common Power" task on page 4-48
Complete the
Step 10
OSC-CSM card installed on the west side.
Complete the
Step 11
OPT-PRE card installed on the east side.
Repeat Steps
Step 12
Cisco ONS 15454 DWDM Installation and Operations Guide, R6.0
4-46
This task verifies the express channel connections during an OADM node
acceptance test.
A tunable laser or eight TXP_MR_2.5G cards covering the 32 C-band
wavelengths (see
DLP-G46 Log into CTC, page 2-25
As needed
Onsite
Superuser
Step 2.
4-4.
"DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task on page 4-41
If Ad-xB-xx.xand AD-xC cards are both installed in one direction, the received express channels
will run into the AD-xB-xx.x cards first, then into the AD-xC-xx.x cards.
"DLP-G83 Verify the OSC-CSM Power on OADM Nodes" task on page 4-43
"DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task on page 4-41
6 through 9 for the AD-xB-xx.x and AD-xC-xx.x cards along the west-to-east direction.
Table 4-1 on page
"DLP-G268 Provision TXP_MR_2.5G Cards for Acceptance
for each east side card. If not, continue with
for each east side card. If not, continue with
for each west side card. If not, continue with
for each west side card. If not, continue with
Chapter 4 Perform Node Acceptance Tests
4-4)
"DLP-G87 Verify the AD-xB-xx.x
Step
"DLP-G88 Verify the AD-xC-xx.x
Step
"DLP-G271 Verify the AD-xC-xx.x
Step
"DLP-G272 Verify the AD-xB-xx.x
Step
September 2005
for the
7.
8.
9.
10.
for the
for the