Suzuki SX4 Service Manual page 1646

Hide thumbs Also See for SX4:
Table of Contents

Advertisement

10E-19 Keyless Start System:
Reference waveform No. 1
Driver, passenger and rear end door / trunk lid antenna
request signals (Request signal (1) transmitted by each
door antenna when each door request switch is pushed)
Measurement
Driver side door antenna
terminal
• CH1: "G16-2" to "G16-9"
• CH2: "G16-1" to "G16-9"
Passenger side door antenna
• CH1: "G16-24" to "G16-9"
• CH2: "G16-23" to "G16-9"
Rear end door / trunk lid antenna
• CH1: "G16-4" to "G16-9"
• CH2: "G16-3" to "G16-9"
Oscilloscope setting CH1: 5 V/DIV, CH2: 5V/DIV
TIME: 40 ms/DIV
Measurement
Request switch of each door is
condition
pushed with remote controller
carried
Reference waveform No. 2
Center antenna signal
(Request signal (1) transmitted by center antenna when
each door request switch is pushed)
Measurement
terminal
Oscilloscope setting CH1: 10 V/DIV, CH2: 2 V/DIV
Measurement
condition
Reference waveform No. 3
Luggage room / trunk room antenna signal
(Request signal (1) transmitted by luggage room / trunk
room antenna when each door request switch is pushed)
Measurement
I4RS0BA50015-02
terminal
Oscilloscope setting CH1: 10 V/DIV, CH2: 10 V/DIV
Measurement
condition
CH1: "G16-6" to "G16-9"
CH2: "G16-5" to "G16-9"
TIME: 20 ms/DIV
• Ignition knob switch of steering
lock unit is pushed
• Request switch of each door is
pushed with remote controller
carried
I5JB0AA50024-03
CH1: "G16-8" to "G16-9"
CH2: "G16-7" to "G16-9"
TIME: 20 ms/DIV
• Request switch of each door is
pushed with remote controller
carried
I5JB0AA50025-02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SX4 and is the answer not in the manual?

Questions and answers

Gawthorpe
February 27, 2025

Adjust throttle motor

1 comments:
Mr. Anderson
February 27, 2025

The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.

This answer is automatically generated

Adetunji Ismail
March 4, 2025

I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,

User image 67c6e55d91ac0
paul murphy
March 19, 2025

My heater stopped working the blower **** is good, control unit ?

1 comments:
Mr. Anderson
March 19, 2025

Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:

1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.

2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.

Checking and addressing these components should help identify and resolve the heater issue.

This answer is automatically generated

ادیک ابرامی
April 21, 2025

دلایل بالا رفتن مصرف بنزین در مدل اتومات

User image 6806728aea58c
jack wrona
March 6, 2025

increasing revs when changing gears

1 comments:
Mr. Anderson
March 6, 2025

The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.

This answer is automatically generated

Table of Contents

Save PDF