10E-5 Keyless Start System:
Door Lock Function of Keyless Start System
When the request switch (1) incorporated in the outside handle of the driver side door, front passenger side door or
rear end door (Hatchback) is pushed, the keyless start control module (2) activates the center antenna (3) and
luggage room antenna (4) (Hatchback) or trunk room antenna (10) (Sedan) to send out the radio wave in the vehicle
compartment to check if the remote controller (5) is in the vehicle compartment or not. When the keyless start control
module receives no signal from the remote controller (i.e., the remote controller does not exist in the vehicle
compartment), it activates the antenna (6) of the door of which the request switch has been pushed to send the
request signal out of the compartment.
If the remote controller exists within the door lock operation area, it receives the request signal sent from the above
said antenna, sends the ID code of the remote controller and the request signal to the keyless start control module and
at the same time, it makes the operation indicator light (7) of the remote controller light up. Lighting of the operation
indicator light indicates that the remote controller sent the ID code and the request signal.
The keyless start control module compares the ID code sent from the remote controller with the ID code registered in
the keyless start control module. If both ID codes match, the keyless start control module outputs the lock or unlock
request signal (depending on the door lock switch (8) state then) to BCM (9). When BCM receives such signal through
CAN communication from the keyless start control module, it activates the door lock actuator to lock or unlock doors.
When the keyless start control module receives a signal from the remote controller (i.e., the remote controller exists in
the vehicle compartment), the function of the keyless start system to prevent the remote controller from being closed in
the vehicle works and the keyless start control module sends a request signal to unlock doors to BCM. In this way,
doors are kept unlocked.
Also, when the driver or passenger has left the vehicle with the remote controller left behind in the vehicle
compartment and locked doors by using the door lock knob or manual door lock switch, the function to prevent the
remote controller from being closed in the vehicle works to unlock doors.
[A]: i) ~ viii)
Furthermore, when ID codes of the remote controller and keyless start control module do not match or the remote
controller exists outside of the operation area, doors are not locked or unlocked even if the request switch of the
outside handle is operated.
2
iii)
vii)
iv)
iii)
i)
vi)
9
viii)
v)
5
7
[A]: Signal flow
ii)
ii)
iii)
10
3
iii)
1
6
8
S7RW0AA501004
iii)
4
iii)
iii)
iii)
I6RW0BA50002-01
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
A Suzuki SX4 that cranks but does not start with a U0100 code (Lost Communication with ECM/PCM) after the crank sensor wire was repaired could have the following issues:
1. Faulty Engine Swap: The engine may not be compatible or not properly installed, as noted in the context that the problem started after an engine replacement.
2. Crankshaft Sensor Issues: Even after repairing the crank sensor wire, the sensor itself could be faulty or not sending a proper signal.
3. ECU Communication Problem (U0100): This indicates a loss of communication with the ECU, possibly due to wiring faults, poor ground connections, or a damaged ECU.
4. Starter Motor Issues: Although the engine cranks, if the starter motor is weak or has voltage issues (as noted with 11.5V), it may not spin the engine fast enough for it to start.
In summary, the likely causes are improper engine installation, crank sensor signal issues, ECU communication failure, or weak starter motor performance.
This answer is automatically generated
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated
دلایل بالا رفتن مصرف بنزین در مدل اتومات
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated