Number Of Encoder Data Sets (Eds) / Eds Count; Encoder Interface (Sensor Module) Component Number; Sensor Module Detection Via Led / Sm Detection Led - Siemens SINAMICS DCM List Manual

2 Parameters
2.2 List of parameters
p0140

Number of Encoder Data Sets (EDS) / EDS count

DC_CTRL, Can be changed: C1(3)
DC_CTRL_R,
Data type: Unsigned8
DC_CTRL_R_S,
P-Group: Data sets
DC_CTRL_S
Not for motor type: -
Min
1
Description: Sets the number of Encoder Data Sets (EDS).
Note: When parameterizing the drive with "no encoder" there must be at least one encoder data set (p0140 >= 1).
p0141[0...n] Encoder interface (Sensor Module) component number / Enc_interf comp_no
DC_CTRL, Can be changed: C1(4)
DC_CTRL_R,
Data type: Unsigned8
DC_CTRL_R_S,
P-Group: Data sets
DC_CTRL_S
Not for motor type: -
Min
0
Description: This parameter is used to assign the encoder data set to an encoder evaluation (e.g. SMC).
This unique component number is assigned when parameterizing the topology.
Only a component number can be entered that corresponds to an encoder evaluation.
Note: If the encoder evaluation and encoder are integrated (motor with DRIVE-CLiQ), then their component numbers are
identical.
For an SMC, different component numbers are assigned for the SMC (p0141) and the (actual) encoder (p0142).
SMC: Sensor Module Cabinet
p0142[0...n] Encoder component number / Encoder comp_no
DC_CTRL, Can be changed: C1(4)
DC_CTRL_R,
Data type: Unsigned8
DC_CTRL_R_S,
P-Group: Data sets
DC_CTRL_S
Not for motor type: -
Min
0
Description: This parameter is used to assign the encoder data set to an encoder.
This assignment is made using the unique component number that was assigned when parameterizing the topology.
Only component numbers can be entered into this parameter that correspond to an encoder.
Note: If the encoder evaluation and encoder are integrated (motor with DRIVE-CLiQ), then their component numbers are
identical.
For an SMC, different component numbers are assigned for the SMC (p0141) and the (actual) encoder (p0142).
p0144[0...n]

Sensor Module detection via LED / SM detection LED

DC_CTRL, Can be changed: U, T
DC_CTRL_R,
Data type: Unsigned8
DC_CTRL_R_S,
P-Group: Encoder
DC_CTRL_S
Not for motor type: -
Min
0
Description: Detects the Sensor Module assigned to this drive and data set.
Note: While p0144 = 1, the READY LED flashes green/orange or red/orange with 2 Hz at the appropriate Sensor Module.
56
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
16
Calculated: -
Dyn. index: EDS, p0140
Unit group: -
Scaling: -
Max
199
Calculated: -
Dyn. index: EDS, p0140
Unit group: -
Scaling: -
Max
199
Calculated: -
Dyn. index: EDS, p0140
Unit group: -
Scaling: -
Max
1
List Manual (LH8), 02/2015, 6RX1800-0ED76
Access level: 2
Func. diagram: 8570
Unit selection: -
Expert list: 1
Factory setting
1
Access level: 3
Func. diagram: 4704, 8570
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 4704
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 2
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
SINAMICS DCM