Page 3
Preface Ordering data SINAMICS Description Assembling Mounting kit to increase the degree of protection to IP20 (Type) test Appendix Hardware Installation Manual 02/2021 A5E34871844B...
Page 4
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
If the general safety instructions and remaining risks are not observed, accidents can occur involving severe injuries or death. • Comply with the general safety instructions in Chapter 1 of the SINAMICS DCM DC Converter Operating Instructions. • Take special care to ensure that the unit is brought into a no-voltage condition and locked out before carrying out any work.
Page 6
SINAMICS DCM List Manual (for DC converters and control modules) Contains parameter list, function diagrams, list of faults and alarms SINAMICS free function blocks, function description Includes a general description, list of parameters, the function block diagrams as well as the list of faults and alarms.
Table of contents Preface ..............................3 Ordering data ............................7 Description ............................. 9 Assembling ............................13 (Type) test ............................17 Appendix ............................. 19 Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
Page 8
Table of contents Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
Ordering data Table 1- 1 Ordering data Article Article number Mounting kit to increase the degree of protection to IP20 for 15 A to 30 A units 6RX1800-0MA00 Mounting kit to increase the degree of protection to IP20 for 60 A to 280 A units 6RX1800-0MA01 Mounting kit to increase the degree of protection to IP20 for 400 A to 600 A units 6RX1800-0MA02...
Page 10
Ordering data Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
The degree of protection indicates protection against touching and penetration of solid objects and/or water. SINAMICS DCM units are delivered with degree of protection IP00 and therefore offer no protection against touching or penetration. The mounting kit for units with a rated DC current up to 850 A help you to achieve degree of protection IP20 on the system side.
Page 12
Technical data The environmental classes and ambient temperatures for the mounting kit correspond to those of the SINAMICS DCM (see SINAMICS DCM Operating Instructions, Chapter 4). Electronics connections (connections onf the CUD) The maximum permissible cable diameter is 10 mm (further information is provided in the SINAMICS DCM Operating Instructions).
Page 13
Description Table 2- 1 Units with armature current from 15 to 30 A (frame size A) Connection Cable diameter 1U1, 1V1, 1W1 (line connection) Ø 0.0 mm ... Ø 10.0 mm 1C1, 1D1 (armature connection) Ø 0.0 mm ... Ø 10.0 mm Protective conductor Ø...
Page 14
Description Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
Assembling Note The mounting kit to increase the degree of protection up to IP20 can only be correctly installed when the unit has already been installed and wired up. WARNING Risk of death if the warning notes are not carefully complied with The units are operated at high voltage levels.
Page 16
Assembling Installing the left and right covers and rails 1. Position the left cover (Pos. 1) from the inside onto the threaded bolts and fasten it using M5 locking nuts (Pos. 197). 2. Insert the straight rail (Pos. 7) and slanted rail (Pos. 8, only for frame size D) by pushing them between the connected cables and use one M4×12 combination screw for each (Pos.
Page 17
Assembling Attach the upper cover using cable ties To fully reach degree of protection IP20, the upper cover must only be able to be released using tools. For example, this can be realized by establishing a snap connection using a 5 mm wide cable tie.
Page 18
Assembling Fully equipped unit (frame size C with installed mounting kit to increase the degree of protection to IP20) Figure 3-2 Example of an installed mounting kit to increase the degree of protection to IP20 Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
(Type) test Final test of the degree of protection After the mounting kit has been installed, a type test must be performed to ensure that a degree of protection IP20 has been reached. Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
Page 20
(Type) test Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
Appendix The following 13 pages contain technical drawings (including remarks and part numbers) to facilitate proper installation. For further information. please refer to the Chapter "Installation". Mounting kit to increase the degree of protection to IP20 Hardware Installation Manual, 02/2021, A5E34871844B...
Page 22
Mounting Instructions IP20 case size A, 15A-30A cable tie as required as required (from inside), 3Nm sheet 1 of 13...
Page 23
Mounting Instructions IP20 detail A case size A, 15A-30A 1: 1 Pos 174 snap in from the outside see detail A see detail A sheet 2 of 13...
Page 24
Mounting Instructions IP20 cable tie case size B, 60 A-280A as required as required (from inside), 3Nm sheet 3 of 13...
Page 25
Mounting Instructions IP20 case size B, 60 A-280A detail A 2: 1 Pos 174 snap in from the outside see detail A see detail A sheet 4 of 13...
Page 26
Mounting Instructions IP20 Pos 9 u 11 for case size B, 60 A-280A small diameter cable Pos 12 u 14 for large diameter cable sheet 5 of 13...
Page 27
Mounting Instructions IP20 cable tie case size C, 400 A-600A as required as required (from inside), 3Nm sheet 6 of 13...
Page 28
Mounting Instructions IP20 case size C, 400 A-600A detail A 2: 1 Pos 174 snap in from the outside see detail A see detail A sheet 7 of 13...
Page 29
Mounting Instructions IP20 case size C, 400 A-600A Pos 9 u 11 for small diameter cable Pos 12 u 14 for large diameter cable sheet 8 of 13...
Page 30
Mounting Instructions IP20 case size C, 400 A-600A on both sides on both sides sheet 9 of 13...
Page 31
Mounting Instructions IP20 case size D, 720 A-850A cable tie as required as required (from inside), 3Nm sheet 10 of 13...
Page 32
Mounting Instructions IP20 case size D, 720 A-850A detail A 2: 1 Pos 174 snap in from the outside siehe detail A siehe detail A sheet 11 of 13...
Page 33
Mounting Instructions IP20 case size D, 720 A-850A Pos 9, 10 u 11 for small diameter cable Pos 12 , 13 u 14 for large diameter cable sheet 12 of 13...
Page 34
Mounting Instructions IP20 case size D, 720 A-850A on both sides on both sides sheet 13 of 13...