p8941[0...3]
CBE2x IP Address of Station / CBE2x IP of Stat
CU_DC (PROFINET
Can be changed: U, T
CBE20), CU_DC_R
Data type: Unsigned8
(PROFINET CBE20),
P-Group: -
CU_DC_R_S
Not for motor type: -
(PROFINET CBE20),
CU_DC_S
Min
(PROFINET CBE20)
0
Description:
Sets the IP address for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Dependency:
Refer to: p8940, p8942, p8943, p8944, p8945
Note:
The interface configuration (p8940 and following) is activated with p8945.
The parameter is not influenced by setting the factory setting.
p8942[0...3]
CBE2x Default Gateway of Station / CBE2x Def Gateway
CU_DC (PROFINET
Can be changed: U, T
CBE20), CU_DC_R
Data type: Unsigned8
(PROFINET CBE20),
P-Group: -
CU_DC_R_S
Not for motor type: -
(PROFINET CBE20),
CU_DC_S
Min
(PROFINET CBE20)
0
Description:
Sets the standard gateway for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Dependency:
Refer to: p8940, p8941, p8943, p8944, p8945
Note:
The interface configuration (p8940 and following) is activated with p8945.
The parameter is not influenced by setting the factory setting.
p8943[0...3]
CBE2x Subnet Mask of Station / CBE2x Subnet Mask
CU_DC (PROFINET
Can be changed: U, T
CBE20), CU_DC_R
Data type: Unsigned8
(PROFINET CBE20),
P-Group: -
CU_DC_R_S
Not for motor type: -
(PROFINET CBE20),
CU_DC_S
Min
(PROFINET CBE20)
0
Description:
Sets the subnet mask for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Dependency:
Refer to: p8940, p8941, p8942, p8944, p8945
Note:
The interface configuration (p8940 and following) is activated with p8945.
The parameter is not influenced by setting the factory setting.
p8944
CBE2x DHCP Mode / CBE2x DHCP Mode
CU_DC (PROFINET
Can be changed: U, T
CBE20), CU_DC_R
Data type: Unsigned8
(PROFINET CBE20),
P-Group: -
CU_DC_R_S
Not for motor type: -
(PROFINET CBE20),
CU_DC_S
Min
(PROFINET CBE20)
0
Description:
Sets the DHCP mode for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Dependency:
Refer to: p8940, p8941, p8942, p8943, p8945
Notice:
When the DHCP mode is active (p8944 > 0), then PROFINET communication via this interface is no longer possible!
However, the interface can be used by the STARTER/SCOUT commissioning tool.
Note:
The active DHCP mode is displayed in parameter r8954.
The interface configuration (p8940 and following) is activated with p8945.
The parameter is not influenced by setting the factory setting.
SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
255
2 Parameters
2.2 List of parameters
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
345