Siemens SINAMICS DCM List Manual page 650

2 Parameters
2.3 Parameters for data sets
p50190[0...n]
p50191[0...n]
p50192[0...n]
p50200[0...n]
p50201[0...n]
p50202[0...n]
p50203[0...n]
p50204[0...n]
p50205[0...n]
p50206[0...n]
p50208[0...n]
p50209[0...n]
p50220[0...n]
p50221[0...n]
p50222[0...n]
p50223[0...n]
p50224[0...n]
p50225[0...n]
p50226[0...n]
p50228[0...n]
p50229[0...n]
p50230[0...n]
p50234[0...n]
p50237[0...n]
p50238[0...n]
p50239[0...n]
p50240[0...n]
p50250[0...n]
p50251[0...n]
p50252[0...n]
p50253[0...n]
p50254[0...n]
p50255[0...n]
p50256[0...n]
p50257[0...n]
p50258[0...n]
p50260[0...n]
p50261[0...n]
p50263[0...n]
p50264[0...n]
p50273[0...n]
p50274[0...n]
p50275[0...n]
p50276[0...n]
p50277[0...n]
p50280[0...n]
p50281[0...n]
p50282[0...n]
p50283[0...n]
p50284[0...n]
p50285[0...n]
p50286[0...n]
p50287[0...n]
p50288[0...n]
p50295[0...n]
650
Cl-loop arm current ctr prectr setpoint smoothing time constant / Ia prec set T
Cl-loop arm current ctr curr controller setp sm time constant / Ia ctr set T
Armature Alpha W limit control word / A Alpha W lim STW
Speed controller speed actual value smoothing time constant / n_ctr n_act T
Band-stop 1 resonant frequency / Band-st 1 f_n
Band-stop 1 quality / Band-st 1 quality
Band-stop 2 resonant frequency / Band-st 2 f_n
Band-stop 2 quality / Band-st 2 quality
Derivative-action element derivative-action time / D-act el t_d-act
Derivative-action element smoothing time / Der-act el t_DAE
Lead/lag element rate time / Lead/lag t_rate
Lead/lag element filter time / Lead/lag t_filter
Speed controller changeover PI/P speed setpoint threshold / PI/P n_set thresh
Speed controller changeover PI/P hysteresis / PI/P hyst
Speed controller changeover PI/P speed actual value threshold / PI/P n_act thresh
Speed controller pre-control enable / n_ctr prec ena
Speed controller integral component configuration / n_ctr I comp conf
Speed controller adaptation Kp y coordinate 2 / Adapt Kp y2
Speed controller adaptation Tn y coordinate 2 / Adapt Tn y2
Speed controller speed setpoint smoothing time constant / n_ctr n_set T
Mast/Sl drive ctr speed controller tracking I component / M/S drve ctr track
Set speed controller integral component duration / Set I_comp dur
Speed controller proportional component enable / n_ctr P_comp ena
Speed controller reference model natural frequency / n_ctrl ref_m fn
Speed controller reference model damping / n_ctrl ref_m d
Speed controller reference model dead time / n_ctr ref_m t_dead
Speed controller reference model activation / n_ctrl ref_m act
Field converter Alpha G limit / Field Alpha G lim
Field converter Alpha W limit / Field Alpha W lim
Field average number of line periods / Field line per no.
Field pre-control activation / Field prec act
Field current controller integral component activation / I_field_ctr I comp
Field current controller P gain / I_field ctr Kp
Field current controller integral time / I_field ctr Tn
Closed-loop field current control standstill field / If_ctr stst_field
Cl-loop field current control field current reduction delay time / If_ctr I_red t_del
Field current pre-control setpoint smoothing time constant / Field_prec set T
Field current controller setpoint smoothing time constant / I_field_ctr set T
Selection of motor flux input variable / Mot fl input sel
Field current controller proportional component activation / I_field_ctr P comp
EMF controller pre-control activation / EMF ctr prec act
EMF controller integral component activation / EMF ctr I comp act
EMF controller P gain / EMF ctr Kp
EMF controller integral time / EMF ctr Tn
EMF controller droop / EMF ctr droop
EMF controller pre-control setpoint smoothing time constant / EMF prec set T
EMF controller setpoint smoothing time constant / EMF ctr set T
EMF controller actual value smoothing time constant / EMF ctr act T
EMF controller pre-control actual value smoothing time constant / EMF prec act T
EMF controller proportional component activation / EMF ctr P comp act
EMF setpoint reduction line voltage smoothing time / EMF set line t_sm
EMF setpoint reduction line voltage upper limit / EMF set line upper
EMF setpoint reduction line voltage lower limit / EMF set line lower
EMF setpoint reduction evaluation factor / EMF set eval_fact
Transition rounding operating mode / RFG rounding mode
List Manual (LH8), 02/2015, 6RX1800-0ED76
SINAMICS DCM