Faults/Alarms Trigger Selection / F/A Trigger Sel - Siemens SINAMICS DCM List Manual

2 Parameters
2.2 List of parameters
p2128[0...15]

Faults/alarms trigger selection / F/A trigger sel

CU_DC, CU_DC_R, Can be changed: U, T
CU_DC_R_S,
Data type: Unsigned16
CU_DC_S, DC_CTRL,
P-Group: Messages
DC_CTRL_R,
Not for motor type: -
DC_CTRL_R_S,
DC_CTRL_S
Min
0
Description: Sets the faults/alarms for which a trigger signal should be generated in r2129.0...15.
Dependency: If the fault/alarm set in p2128[0...15] occurs, then the particular binector output r2129.0...15 is set.
Refer to: r2129
p2128[0...15] Faults/alarms trigger selection / F/A trigger sel
TM150, TM15DI_DO, Can be changed: U, T
TM31
Data type: Unsigned16
P-Group: Messages
Not for motor type: -
Min
0
Description: Sets the faults/alarms for which a trigger signal should be generated in r2129.0...15.
Dependency: If the fault/alarm set in p2128[0...15] occurs, then the particular binector output r2129.0...15 is set.
Refer to: r2129
r2129.0...15 CO/BO: Faults/alarms trigger signal / F/A trigger signal
All objects Can be changed: -
Data type: Unsigned16
P-Group: Messages
Not for motor type: -
Min
-
Description: Display and BICO output for the trigger signals of the faults/alarms set in p2128[0...15].
Bit field: Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Dependency: If the fault/alarm set in p2128[0...15] occurs, then the particular binector output r2129.0...15 is set.
Refer to: p2128
Note: CO: r2129 = 0 --> None of the selected messages has occurred.
CO: r2129 > 0 --> At least one of the selected messages has occurred.
176
Signal name
Trigger signal p2128[0]
Trigger signal p2128[1]
Trigger signal p2128[2]
Trigger signal p2128[3]
Trigger signal p2128[4]
Trigger signal p2128[5]
Trigger signal p2128[6]
Trigger signal p2128[7]
Trigger signal p2128[8]
Trigger signal p2128[9]
Trigger signal p2128[10]
Trigger signal p2128[11]
Trigger signal p2128[12]
Trigger signal p2128[13]
Trigger signal p2128[14]
Trigger signal p2128[15]
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
65535
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
65535
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
List Manual (LH8), 02/2015, 6RX1800-0ED76
Access level: 3
Func. diagram: 8070
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 8050, 8070
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 8070
Unit selection: -
Expert list: 1
Factory setting
-
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SINAMICS DCM
FP
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-