Toshiba e-STUDIO206L Service Manual page 576

Error code Classification
C911 Circuit related
service call
C940 Circuit related
service call
C970 Process related
service call
CA10 Laser optical unit
related service call
CA20
CB00 Finisher related
service call
CB01
CB10
CB11
CB12
CB13
CB14
CB30
CB31
CB40
CB50
CB51
e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507
ERROR CODE AND TROUBLESHOOTING
Contents
Toner cartridge IC chip abnormality
Engine-CPU abnormality
High-voltage transformer abnormality: Leakage of the
main charger is detected.
Polygonal motor abnormality: The polygonal motor is not
rotating normally.
H-Sync detection error: H-Sync detection PC board
cannot detect laser beams.
Finisher not connected
Finisher communication error
Entrance motor abnormality: The entrance motor is not
rotating normally. [MJ-1101/1107/MJ-1106/1108]
Buffer tray guide motor abnormality: The buffer tray guide
motor is not rotating or the buffer tray guide is not moving
normally. [MJ-1101/1107/MJ-1106/1108]
Buffer roller drive motor abnormality: The buffer roller
drive motor is not rotating or the buffer roller is not moving
normally. [MJ-1101/1107/MJ-1106/1108]
Finisher exit motor abnormality [MJ-1101/1107/MJ-1106/
1108]
Paper holding arm motor abnormality [MJ-1101/1107/MJ-
1106/1108]
Movable tray shift motor abnormality: The movable tray
shift motor is not rotating or the movable tray is not
moving normally. [MJ-1101/1107]
Movable tray shift motor abnormality: The movable tray
shift motor or the movable tray does not work properly.
[MJ-1032]
Movable tray shift motor abnormality: The movable tray
shift motor or the movable tray does not work properly.
[MJ-1033]
Movable tray paper-full detection error: The actuator of
the movable tray paper-full detection sensor does not
move smoothly. [MJ-1101/1107/MJ-1106/1108]
Front alignment motor abnormality: The front alignment
motor is not rotating or the front align/1106/1108ment
plate is not moving normally. [MJ-1101/1107]
Front alignment plate home position detection error: The
detection of the home position ends abnormally because
the front alignment plate has not worked properly.
[MJ-1032/MJ-1033]
Stapler home position error: The stapler home position
sensor does not work. [MJ-1101/1107/MJ-1106/1108]
Stapler unit home position detection error: The detection
of the home position of the stapler unit ends abnormally.
[MJ-1032/MJ-1033]
Stapler shift home position error: The stapler is not at the
home position. [MJ-1101/1107/MJ-1106/1108]
Stapler unit sliding home position detection error: The
detection of the home position of the stapler unit sliding
ends abnormally. [MJ-1032/MJ-1033]
8 - 16
© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved
Troubleshooting
P. 8-140
P. 8-151
P. 8-140
P. 8-154
P. 8-154
P. 8-155
P. 8-155
P. 8-155
P. 8-156
P. 8-156
P. 8-157
P. 8-157
P. 8-158
P. 8-159
P. 8-160
P. 8-160
P. 8-161
P. 8-163
P. 8-163
P. 8-164
P. 8-164
P. 8-165
P. 8-166
P. 8-167