NEC Univerge sv8500 Manual page 1459

COMMAND No. SUB COMMAND
1 CALL_HOLD
2 CONFIG
3 DHCP
4 DNS_SW
5 DRSADDRESS
6 DRSQOS
7 DTMF_IN
8 E_T_TIME
9 E_T_WAITTIME
10 EC_TRAINING
11 FAX_ECM
12 FAXERRORDETECT
13 GND_OPEN_SW
14 IMPEDANCE
15 INTERFACE
16 IPADDRESS
17 ONE_TIME_PASS
OWN_NAME
PAD0
SHOW
18 PAD1
PAD2
PAD3
19 PAD4
20 PRI_COMMON1
21 PRI_LOOPBACK
22 PRI_E1_1
23 PRI_E1_2
24 RTP_STOP_DETECT
SIGNALING_PORT_
25
NO
26 SIGNALING_QOS
27 SIPSV_IPADDRESS
28 SMOOTH_PAD
29 STARTPORT
30 TCP_TIMER
31 VERSION
32 VLAN
33 WARNING_TONE
PING -
DELETE VLAN
SAVE CONFIGDATA
GET CONFIGDATA
PUT CONFIGDATA
REBOOT -
EXIT -
INIT CONFIG
List of Maintenance Command (Continued)
Displays the state of call hold setting
Displays the state of DHCP setting
Displays the state of DHCP setting
Displays the DNS setting
Displays the setting of DRS (IP address and port No.)
Displays the QoS setting of DRS session
Displays the DTMF relay of in-band signaling
Displays the period to be executed echo canceller training
Displays waiting time before starting echo canceller training
Displays echo canceller training setting
Displays the FAX ECM setting
Displays the FAX switching time
Displays the Grand open switch setting.
Displays the impedance setting.
Displays the connection mode.
Displays IP address, netmask, and default Gateway.
Displays the one-time password.
Displays the own host name.
Displays PAD setting.
Displays settings for flexible PAD 1
Displays settings for flexible PAD 2
Displays settings for flexible PAD 3
Displays settings for flexible PAD 4
Displays common setting 1 of PRI (2M)
Displays MB of loopback and Dch
Displays function settings on Dch of PRI (2M)
Displays function settings 1 (Alarm/Signaling) on Dch of PRI (2M)
Display the time-out value for RTP reception
Displays the Signaling Port Number for SIP Mode.
Displays the QoS of Signaling Port Number for SIP Mode.
Displays the network settings of SIP Server.
Displays the setting of Smooth PAD mode
Displays the number of RTP Start Port
Displays the setting of the timer for TCP link connection
Displays the release version of firmware and hardware
Displays the state of VLAN setting
Displays the setting of Warning Tone
Checks the connectivity of network
Deletes the VLAN setting designating by the VLAN ID
Saves the configuration data
Downloads a system data file from specified TFTP server
Uploads a system data file to specified TFTP server
Reboots the MG
Exits the maintenance command
Initialize the config command
VOL.2-1206
MG(PRI) (2M) [SCA-30PRIA/MG-30PRIA]
FUNCTION PAGE
page 1236
page 1236
page 1236
page 1236
page 1236
page 1237
page 1238
page 1238
page 1238
page 1238
page 1238
page 1238
page 1239
page 1239
page 1239
page 1239
page 1239
page 1239
page 1240
page 1240
page 1241
page 1241
page 1242
page 1242
page 1242
page 1242
page 1243
page 1244
page 1244
page 1244
page 1245
page 1246
page 1246
page 1246
page 1247
page 1247
page 1247
page 1247
page 1248
page 1248
page 1249