Chevrolet 10 Series 1970 Service Manual page 86

BODY 1B-8
F ig . 2 0 —Side C ow l V e n tila to r
7. Inspect cow l hood ledge sea l fo r fatigue or cuts and
rep lace if n ecessary.
8. Secure fron t edge o f g r ille ov er lip of hood s ea l with
six retaining screw s.
9. R ein stall windshield
10. R e v e rs e rem oval p roced u re to install.
COW L AIR VENTILATOR VALVE ASSEMBLY
Replacem ent
E n tire outlet valve assem bly may be rem oved fro m
the v eh icle by rem ovin g two screw s
pins. R e fe r to Figu re 20. A ls o r e fe r to F igu re 20 fo r
DASH &
roE
F ig . 2 1 —C o w l V e n ti la to r —F /F C ow ls
TO INSTALL OR REMOVE
DEPRESS PIN
INSTALL CLIP
BETWEEN TABS
O N VA LV E A S M
INSTALL K N O B UNTIL
THREADS BOTTOM
O UT A N D TIGHTEN
TO CORRECT
POSITION
w ip er arm s on p ivot shafts.
and dep ress the
INSTRUMENT
PNL. REINF.
disassem bly of the fla t fa ce cow l a ir ven tila to r assem bly.
WINDSHIELD WIPERS
W indshield w iper units on a ll m odels a re of the two-
speed e le c tr ic type. A sin gle w iper m otor unit, mounted
to cen ter of cowl inside cab, pow er both w iper blades.
The w ip er blade operating link rods and pivot mountings
on these m odels are located in the outside a ir inlet
plenum cham ber.
Arm Adjustm ent
T o adjust sweep of blades to p rovid e maximum v is i­
b ility , turn on w ipers, then note sweep of arm s. If
n ecessary, rem ove one o r both arm s as fo llow s:
outer end of arm away fro m glass which w ill trip lock
sprin g at base of arm and re le a s e sprin g fro m undercut
of p ivot shaft. W hile holding arm in this position, pull
outward on cap section at base of arm to rem o ve arm.
A rm can be rein sta lled in any one of s e v e r a l positions
due to serra tion s on p ivot shaft and in arm cap (fig . 22).
W ip er Arm Pivot Shafts and Link Rod (Fig. 19)
Removal
1. R em ove windshield w ip er arm s fro m p ivot shafts.
P roced u re fo r rem ovin g arm s is explained p r e v i­
ously under " A r m Adjustm ents."
2. R em ove screw s which attach outside a ir cow l ven ti­
lato r g r ille to cowl. C a refu lly rem ove g r ille fo rw a rd
fro m cowl.
3. A t cen ter of cowl, rem ove reta in er (fig . 19) which
attaches each link rod to m otor d riv e linkage and
arm assem bly. D isengage
4. R em ove two screw s which attach arm tran sm ission
pivot shaft assem bly to cow l.
assem bly with link rod fro m plenum cham ber.
Installation
1. P la c e pivot shaft assem bly with link rod into p o s i­
tion at cowl bracket.
with two screw s (fig . 22).
2. Attach end of link rod to linkage of m otor d rive
and arm assem bly at center of cowl. Secure rod
with reta in er. If opposite p ivot shaft and link rod
was rem oved, in stall it at the sam e tim e.
3. Install outside a ir cow l ven tila tor g r ille to top of
cowl using screw s (fig . 19).
Pu ll
link rods fro m pins.
R em ove pivot shaft
Secure assem bly to bracket
CHEVROLET TRUCK SERVICE MANUAL