Chevrolet 10 Series 1970 Service Manual page 519

5. R em ove the d irection a l signal cancelling cam.
m ove the d irection al signal switch le v e r .
6. R em ove the column w irin g harness co ver.
7. R em ove the d irection a l signal switch screw s.
8. Rotate the d irection a l signal switch housing counter­
clock w ise and rem ove the housing fro m the column.
NOTE: The housing and switch cannot be fu lly
rem o ved fro m the column until the shift le v e r
housing is rem oved.
9. R em ove the p la stic thrust washer assem bly and then
re m o v e the shift le v e r housing (or extension housing)
fro m the column.
10. Separate the d irection a l signal switch, switch control
support assem bly, d irection a l
shift le v e r housing (or housing extension) assem blies.
11. P r e s s the steerin g shaft upper bearing out of the
switch contact support.
12. R em ove the shift le v e r housing (or extension housing)
seat and bushing fro m the upper end of the column.
13. R em ove the bolt and screw s fro m the adjusting ring
clamp and rem ove the clam p, adjusting ring and
lo w e r b earin g. P r e s s the lo w e r bearin g out of the
adjusting ring.
14. 3-Speed Columns - R em ove
and le v e r spacer.
Autom atic Columns
clam ping ring screw s (3).
15. P la c e the column upright on the flo o r , supporting it
with two p ieces of wood.
the upper end of the shift tube.
shift le v e r with foot while tapping on the wood block
to withdraw the tube fro m the column jacket.
NOTE: In some tolera n ce stack-up cases it
m ay be n ecessary to use a p ress.
not to damage the tube o r jacket.
16. R em ove the fe lt seal fro m the shift tube.
17. R em ove fir e w a ll clam p, toe pan seal and dash panel
seals fro m the jacket.
Assem bly— 1 0 -3 0 Series
NOTE: F o r flo o r shift m odels, om it Steps 2,
3, 4, 5 and 13.
1. In stall the dash panel seal, toe panel and fir e w a ll
clam ps o v e r the end of the jacket.
2. Lu b ricate a ll b earing su rfaces on the shift tube.
3. P la c e the fe lt seal onto the shift tube (next to spring)
and then place the shift tube in the jacket.
4. 3-Speed Columns - T e m p o ra rily in stall spacer, ls t -
r e v e r s e shift le v e r and lo w e r adjusting ring.
a block of wood on top of the adjusting ring and tap
until the shift tube bottom s.
shift le v e r and spacer.
NOTE: The shift tube spring reta in er must be
bottom ed against the jacket stops.
Autom atic Columns - A lign the three holes in the se ­
le c to r plate with the th ree holes in the jacket, p o si­
tion the clamping ring and in stall the three screw s.
5. 3-Speed Columns - Lubricate and in stall the spacer
and ls t - r e v e r s e shift le v e r (tang of le v e r towards
top of column).
6. In stall lo w e r bearing in the adjusting ring and then
in stall the adjusting ring, clamp and screw s.
signal housing and
ls t - r e v e r s e shift le v e r
- R em ove the s e le c to r plate
P la c e a block of wood on
P r e s s down on the
Be carefu l
P la ce
R em ove adjusting ring,
R e ­
7. In stall the shift le v e r housing (or extension housing)
seat and bushing to upper end of housing.
8. Thread direction al
through the switch and shift le v e r
housings, lubricate the inner diam eter o f the shift
housing, and then place the shift le v e r (or extension)
housing onto the upper end of the column.
9. In stall the switch housing pla stic washer assem bly.
P r e s s the upper bearing into the switch contact sup­
port.
10. In stall the d irection a l signal switch housing, contact
support, bearing and switch and torque the switch
screw s to 25 in. lbs.
11. In stall the column w irin g harness co v er and back-up
lam p switch.
12. In sta ll the direction a l signal and gea rsh ift le v e r s .
13. Adjust the shift tube as outlined under "S h ifter Tube
A dju stm ent."
14. P M odels - L oo sely in stall the lo w er bearing preload
spring and clamp.
C and K M odels - L o o se ly in stall the lo w er bearing
preload spring and washer.
ing shaft and coupling to the upper steerin g shaft and
torque the coupling clamp bolt to 120 in. lbs.
15. Slide the steerin g shaft assem bly up through the
column assem bly.
cancelling cam, steerin g shaft nut and lock washer.
Disassembly—4 0 -5 0 -6 0 Series (Fig.
1. R em ove the d irection a l signal cancelling cam.
2. R em ove the upper bearin g snap ring and p ry out
bearing.
3. Slide the steerin g shaft out of the m ast jacket from
the lo w er end, along with the low er bearin g clamp,
seal, spring, bearing seat and fe lt washer.
4. R em ove the lo w e r b earin g fro m the m ast jacket.
5. Rem ove the turn signal switch le v e r.
th ree turn signal switch screw s and rem ove the turn
signal switch and support.
6. Rotate the turn signal housing cou n ter-clockw ise and
rem ove housing fro m the m ast jacket.
Assem bly— 4 0 -5 0 -6 0 Series
1. Install the turn signal switch housing onto the upper
end of the m ast jacket.
2. In stall the turn signal switch support, switch and
le v e r.
3. P o sitio n the clam p, seal spring, bearing seat, fe lt
washer and bearing on the low er end of the shaft.
NOTE: Lu bricate the seal with silicon e grease.
4. C a refu lly in se rt the steerin g shaft into the m ast
jacket fro m the lo w e r end, install the upper bearin g
and retaining ring.
5. Adjust the lo w e r bearin g clamp to allow .005 to .030
axial m ovem ent of the shaft and tighten the lo w er
clamp bolt to 120 in. lbs.
6. Install the turn signal cancelling cam, spring, shaft
washer and nut.
Installation
M an d ato ry Sequence—C -P -K l0 -2 0 -3 0 Models (Fig. 16)
1. Adjust the m ast jacket lo w er bearing p reload by po­
sitioning spring and interm ediate coupling housing
(C -K M odels)
STEERING 9-11
signal switch w irin g
(o r extension)
Install the lo w er s te e r ­
Install the direction al
1 8 )
Rem ove the
o r clam p (P M odels) to maintain
CHEVROLET TRUCK SERVICE MANUAL
harness
signal