Chevrolet 10 Series 1970 Service Manual page 584

ELECTRICAL—BODY AND CHASSIS 12-22
three o r four term in als.
four term in al assem bly
three term in al and the four term in al m odels.
Two switches, connected in p a ra lle l, control the s ta r t­
WIPER M O TO R
REMOVAL A N D INSTALLATION
1 0 -6 0 .C onventional Cab M odels (Fig. 18)
1. Disconnect battery ground cable.
2. Rem ove w ip er arm s and blades fro m transm ission
shaft.
3. R em ove plenum cham ber g r ille .
4. Disconnect w ip er d riv e
m ove crank arm nut and arm
5. W orking under instrum ent console, disconnect w ip er
m otor and w asher w irin g connectors.
NOTE: If veh icle is equipped with a parking
brake assem b ly located on the v e r tic a l surface
o f the cow l front panel (d ire c tly below the w iper
m otor, rem ove the parking brake assem bly at­
taching bolts (4) to allow shifting o f the assem bly
rea rw a rd s in o rd e r to p rovid e access fo r r e ­
m oval and in stallation
assem bly.
Disconnect and rem ove left-hand d e fro s te r hose.
6. Disconnect w asher hoses fro m w asher pump.
7. Rem ove m otor attaching s c rew s and m otor fro m cowl
mounting position.
8. To in stall, r e v e r s e rem ova l p rocedu re.
NOTE: Make certain w iper
are in the " P a r k " position.
F ig . 18—W ip e r M o to r In s ta lla tio n —C o n v e n tio n a l Cab
F o r s e r v ic e replacem ent a
is used, s e rv ic in g both, the
SERVICE OPERATIONS
rods fro m crank arm ; r e ­
fro m m otor shaft.
o f the w ip er m otor
m otor and blades
ing, stopping and parking o f the Type " E " w iper m otor.
The manually operated start, stop switch is located on the
instrum ent panel, while the cam operated park switch is
located in the w iper gear box.
Tilt Cab M odels (Fig. 19)
NOTE: Two separate m otors a re used to pow er
the w ip ers, one switch con trollin g both. F igu re
19 is an exploded view o f the le ft hand w iper a s ­
sem bly installation.
identical, how ever, it w ill be n ecessa ry to r e ­
m ove heater co v e r assem bly b e fo re w ip er m otor
may be s erviced .
1. Disconnect battery ground cable.
2. Rem ove nut retaining w iper on to shaft.
3. Pu ll arm , knurled d r iv e r and rain shield fro m shaft.
4. Rem ove nut retaining shaft fe rru le
panel; rem ove washers.
5. F rom inside veh icle, rem ove four screw s retaining
m otor assem bly to dash and rem ove assem bly from
veh icle.
6. To in stall, re v e r s e rem oval procedu re.
F ig . 19—W in d s h ie ld W ip e r Assem bly - T ilt Cab
1. C row n N u t
2. Lock W asher
3. W ip e r Arm Assem bly
4 . K n u rle d D riv e r
5. Rain S hield
6. S haft Ferru le R etaining
N u t
Right hand assem bly is
to body outer
7. O u te r W asher
8. Inner W asher
9. S haft F e rru le (P art of.
M o to r A ssem bly)
10. R eta in ing Bolts
11. M o to r A ssem bly (In cludes
B racket)
CHEVROLET TRUCK SERVICE MANUAL