Table of Contents
Advertisement
CLUTCHES AND TRANSMISSIONS 7-22
1 Boot Retainer
2 Boot
3 Selector Finger Pin
4 Control C over
5 Pivot Screw
6 Shift Rod
7 Selector Rod
8 Adjustable C levis
F ig . 2 D —C o n tro l Island S h ift M echanism
Assembly
NOTE:
K ey numbers in follow ing text r e fe r to
F igu re 2D.
1. P la c e gearsh ift le v e r on shift le v e r fin ger (10) and
position in control co v e r. Install pivot pin (13) and
r o ll pin (12).
2. Install s e le c to r fin g er strap and pin assem bly (11),
w ashers and two p ivot screw s (5). Torqu e screw s to
60-65
ft. lbs. and install new lo c k w ire s to pivot
screw s.
3. Install s e le c to r fin g er pin (3), s e le c to r fin ger (9),
washer and new cotter pin.
Installation
NOTE:
Key numbers in text r e fe r to F igu re 2D.
1. Install boot (2), boot reta in er (1) and gea rsh ift knob
to shift mechanism assem b ly.
2. P la c e
shift assem bly in p rop er position on control
island and install attaching parts.
3. Connect shift control linkage to s ele cto r fin ger (9)
and shift fin ger (10), then adjust control linkage as
covered
p reviou sly
procedures.
REMOTE CONTROL ASSEMBLY
(AT TRANSM ISSIO N)
T ilt cab veh icles have transm ission rem ote control a s
sem b lie s as shown in F ig u res
p a rts becom e worn or d e fective, make re p a irs as de
scrib ed in the follow ing text:
9 Selector Finger
10 Shift Finger
11 Selector Finger Strap
and Pin Assem bly
12 R oll Pin
13 Pivot Pin
14 Gearshift L ev e r
under
"L in k a g e
Adjustm ent7'
3D, 4D and 5D. Should
Removal
1. P osition
transm ission
T R A L " and disconnect control rods fro m shift le v e r s
at transm ission.
NOTE:
On
m odels with New P ro c e s s tran s
m ission,
rem ove s e le c to r le v e r bellcran k snap
ring.
2. R em ove
rem ote
control assem b ly-to-tra n sm issio n
c o ve r attaching parts, then rem ove assem bly from
veh icle.
NOTE:
On veh icles with Spicer transm issions
(see fig. 3D), in addition to rem ovin g the above
attaching parts, it is n ecessary to rem ove the
reta in er, plunger pin spring, and plunger pin.
C A R E F U L L Y rem ove rem ote control assem bly,
keeping the assem bly sligh tly tilted to the left,
as shown, so that the plunger w ill not fa ll into
the transm ission.
3. P la ce
a
clean
shop
opening to prevent entry o f d irt o r other foreign
m ateria l.
Installation
1. P osition a new gasket on tran sm ission cover.
2. With a ll parts in " N E U T R A L "
place
rem ote
control
cover.
NOTE:
On ve h ic le s with Spicer transm issions
(see fig . 4D), position plunger in 1st and r e v e r s e
shift fin ger; then ca refu lly install rem ote control
assem bly,
as
shown,
sligh tly tilted to the left to preven t the plunger
f r o m
fallin g
i n t o
plunger pin, plunger pin spring, and retain er.
Shift Rod
Poppet Springs
Plunger
Retainer ^ K p j n Spring
F ig . 3 D —S picer Remote C o n tro l Assem bly
gea rsh ift
le v e r
in
" N E U
cloth o v e r the transm ission
position, ca refu lly
assem bly
on
transm ission
keeping
t h e
assem bly
the
transm ission.
Install
Remote Control
Assembly
Plunger
Gasket
i st a n a
Shift
Transmission
Shifter Housing
Assembly
Plunger Pin
CHEVROLET TRUCK SERVICE MANUAI
Hide quick links:
Advertisement
Chapters
Table of Contents
