Download Print this page

Juniper JUNOSE SOFTWARE 11.2.X - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010 Command Reference Manual

Software for e series broadband services routers command reference a to m

Hide thumbs Also See for JUNOSE SOFTWARE 11.2.X - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010:

Manual (282 pages)

Table Of Contents

page of 1502

/ 1502
Contents
Table of Contents
Bookmarks

Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual

JunosE™ Software

for E Series™ Broadband

Services Routers

Command Reference A to M

Release

11.2.x

Published: 2010-07-19

Copyright © 2010, Juniper Networks, Inc.

Table of Contents

Advertisement

Table of Contents

Need help?

Need help?

Do you have a question about the JUNOSE SOFTWARE 11.2.X - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010 and is the answer not in the manual?

Questions and answers

Summary of Contents for Juniper JUNOSE SOFTWARE 11.2.X - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Page 1 JunosE™ Software for E Series™ Broadband Services Routers Command Reference A to M Release 11.2.x Published: 2010-07-19 Copyright © 2010, Juniper Networks, Inc.
Page 2 Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
Page 3 REGARDING LICENSE TERMS. 1. The Parties. The parties to this Agreement are (i) Juniper Networks, Inc. (if the Customer’s principal office is located in the Americas) or Juniper Networks (Cayman) Limited (if the Customer’s principal office is located outside the Americas) (such applicable entity being referred to herein as “Juniper”), and (ii) the person or organization that originally purchased from Juniper or an authorized Juniper reseller the applicable...
Page 4 Customer shall be liable for any such violations. The version of the Software supplied to Customer may contain encryption or other capabilities restricting Customer’s ability to export the Software without an export license. Copyright © 2010, Juniper Networks, Inc.
Page 5 (including Juniper modifications, as appropriate) available upon request for a period of up to three years from the date of distribution. Such request can be made in writing to Juniper Networks, Inc., 1194 N. Mathilda Ave., Sunnyvale, CA http://www.gnu.org/licenses/gpl.html...
Page 6 Copyright © 2010, Juniper Networks, Inc.
Page 7 Index ............1435 Copyright © 2010, Juniper Networks, Inc.
Page 8 JunosE 11.2.x Command Reference Guide A to M viii Copyright © 2010, Juniper Networks, Inc.
Page 9: Table Of Contents
......... 41 Copyright © 2010, Juniper Networks, Inc.
Page 10 ..........93 Copyright © 2010, Juniper Networks, Inc.
Page 11 ............144 Copyright © 2010, Juniper Networks, Inc.
Page 12 ........195 Copyright © 2010, Juniper Networks, Inc.
Page 13 ........... . . 243 Copyright © 2010, Juniper Networks, Inc.
Page 14 ......... . 292 Copyright © 2010, Juniper Networks, Inc.
Page 15 ....... . 344 Copyright © 2010, Juniper Networks, Inc.
Page 16 ..........397 Copyright © 2010, Juniper Networks, Inc.
Page 17 ........... 446 Copyright © 2010, Juniper Networks, Inc.
Page 18 ..........506 xviii Copyright © 2010, Juniper Networks, Inc.
Page 19 ......... . . 557 Copyright © 2010, Juniper Networks, Inc.
Page 20 ........... . 609 Copyright © 2010, Juniper Networks, Inc.
Page 21 ........... 656 Copyright © 2010, Juniper Networks, Inc.
Page 22 ..........704 xxii Copyright © 2010, Juniper Networks, Inc.
Page 23 ........... 756 Copyright © 2010, Juniper Networks, Inc.
Page 24 ........805 xxiv Copyright © 2010, Juniper Networks, Inc.
Page 25 ......855 Copyright © 2010, Juniper Networks, Inc.
Page 26 ............904 xxvi Copyright © 2010, Juniper Networks, Inc.
Page 27 ..........955 Copyright © 2010, Juniper Networks, Inc.
Page 28 ..........1004 xxviii Copyright © 2010, Juniper Networks, Inc.
Page 29 ..........1054 Copyright © 2010, Juniper Networks, Inc.
Page 30 ........... 1104 Copyright © 2010, Juniper Networks, Inc.
Page 31 ..........1154 Copyright © 2010, Juniper Networks, Inc.
Page 32 ............1203 xxxii Copyright © 2010, Juniper Networks, Inc.
Page 33 ............1256 Copyright © 2010, Juniper Networks, Inc.
Page 34 ..........1306 xxxiv Copyright © 2010, Juniper Networks, Inc.
Page 35 ..........1359 Copyright © 2010, Juniper Networks, Inc.
Page 36 ..........1410 xxxvi Copyright © 2010, Juniper Networks, Inc.
Page 37 Index ............1435 Copyright © 2010, Juniper Networks, Inc.
Page 38 JunosE 11.2.x Command Reference Guide A to M xxxviii Copyright © 2010, Juniper Networks, Inc.
Page 39: List Of Tables
ERX310 Router ..........5 Table 4: Interface Types and Specifiers for E120 Router and E320 Router ..13 Copyright © 2010, Juniper Networks, Inc. xxxix...
Page 40 JunosE 11.2.x Command Reference Guide A to M Copyright © 2010, Juniper Networks, Inc.
Page 41: About The Documentation
Audience This guide is intended for experienced system and network specialists working with Juniper Networks E Series Broadband Services Routers in an Internet access environment. E Series and JunosE Text and Syntax Conventions Table 1 on page xlii defines notice icons used in this documentation.
Page 42: Table 1: Notice Icons
Indicates that you must press two or more Press Ctrl + b. keys simultaneously. Syntax Conventions in the Command Reference Guide Plain text like this Represents keywords. terminal length Italic text like this Represents variables. mask, accessListName xlii Copyright © 2010, Juniper Networks, Inc.
Page 43: Obtaining Documentation
CD-ROMs or DVD-ROMs, see the Portable Libraries page at http://www.juniper.net/techpubs/resources/index.html Copies of the Management Information Bases (MIBs) for a particular software release are available for download in the software image bundle from the Juniper Networks Web site at http://www.juniper.net/...
Page 44: Self-Help Online Tools And Resources
7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features: Find CSC offerings: http://www.juniper.net/customers/support/...
Page 45: Commands, A To M
F Commands on page 619 G Commands on page 657 H Commands on page 673 I Commands on page 689 K Commands on page 1137 L Commands on page 1141 M Commands on page 1251 Copyright © 2010, Juniper Networks, Inc.
Page 46 JunosE 11.2.x Command Reference Guide A to M Copyright © 2010, Juniper Networks, Inc.
Page 47: Command Reference Topics
If using the option changes the behavior of the no version, the individual command entry in this guide describes the difference in behavior. Copyright © 2010, Juniper Networks, Inc.
Page 48: Deprecated Commands
2 1 ip rip send version 1 ip rip authentication mode md5 17 ip rip authentication key ip route 10.6.0.0 255.255.0.0 192.168.1.1 ip route 10.10.0.0 255.255.0.0 192.168.1.1 ip route 10.10.0.166 255.255.255.255 192.168.1.1 Copyright © 2010, Juniper Networks, Inc.
Page 49: Interface Types And Specifiers
Table 3 on page 5 lists the interface specifiers for each type of interface on ERX7xx models, ERX14xx models, and the Juniper Networks ERX310 Broadband Services Router. NOTE: On ERX7xx models, ERX14xx models, and the ERX310 router, you can use the atm slot/port/vpi/vci interface specifier format as an alternative to the atm slot/port.subinterface format with the specific show interface and show subinterface...
Page 50 ATM 1483 subinterface; allowable numeric range depends on the module capabilities and current configuration vci—Virtual circuit identifier of the PVC on this ATM 1483 subinterface; allowable numeric range depends on the module capabilities and current configuration Copyright © 2010, Juniper Networks, Inc.
Page 51 PPPoE subinterfaces per Fast Ethernet line module No VLANs: subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1–2147483647; no more than 8000 PPPoE subinterfaces per Fast Ethernet line module subinterface2—Not used Copyright © 2010, Juniper Networks, Inc.
Page 52 1–4294967293 mlframe-relay Multilink bundle-name[.subinterface ] mlframe-relay frame relay boston.1 bundle-name—Name of the bundle interface subinterface—Number of the MLFR subinterface in the range 1–4294967293 mlppp Multilink PPP bundle-name mlppp chicago interface bundle-name—Name of the bundle Copyright © 2010, Juniper Networks, Inc.
Page 53 0–2 (ERX310 router) port—Port number on the I/O module subinterface—Number of the subinterface in the range 1–2147483647 serial CT3, E3 Refer to the individual formats listed below. Frame, T3 Frame, or cOCx/STMx interface Copyright © 2010, Juniper Networks, Inc.
Page 54 (the router assigns the number one to an unframed E1 channel) subinterface—Number of the subinterface in the range 1–2147483647 Copyright © 2010, Juniper Networks, Inc.
Page 55 0–2 (ERX310 router) port—Port number on the I/O module path-channel—Number of the STS-1or STM-0 line in the range 1–2147483648 ds3-channel-number—Number of a T3 channel subinterface—Number of the subinterface in the range 1–2147483647 Copyright © 2010, Juniper Networks, Inc.
Page 56 I/O module tunnel Tunnel tunnel-type:tunnel-name[.subinterface ] tunnel gre:boston interface tunnel-type—Type of the tunnel: dvmrp, gre, ipsec, l2tp, or mpls tunnel-name—Name of the tunnel subinterface—For GRE tunnels, number of the subinterface in the range 1–2147483647 Copyright © 2010, Juniper Networks, Inc.
Page 57: Table 4: Interface Types And Specifiers For E120 Router And E320 Router
ATM 1483 subinterface; numeric range for the E120 and E320 routers is 0–255 vci—Virtual circuit identifier of the PVC on this ATM 1483 subinterface; numeric range for the E120 and E320 routers is 1–65535 Copyright © 2010, Juniper Networks, Inc.
Page 58 1–2147483647; no more than 16,000 PPPoE subinterfaces per Gigabit Ethernet line module subinterface2—Not used IEEE 802.3ad bundle-name[.subinterface ] lag paris.2 link bundle-name—Name of the bundle aggregation group (LAG) subinterface—Number of the LAG interface subinterface in the range 1–2147483647 Copyright © 2010, Juniper Networks, Inc.
Page 59 IOA bay (E120 router) or the lower IOA bay (E320 router). port—Port number on the IOA subinterface—Number of the subinterface in the range 1–2147483647 mplsMinor MPLS minor [ vr:]tunnel-name mplsMinor interface lsp-02020202-1-4 vr—Name of a virtual router tunnel-name—Name of the tunnel Copyright © 2010, Juniper Networks, Inc.
Page 60 IOA bay (E120 router) or the upper IOA bay (E320 router). 1 indicates that the IOA is installed in the left IOA bay (E120 router) or the lower IOA bay (E320 router). port—Port number on the IOA Copyright © 2010, Juniper Networks, Inc.
Page 61 PPPoE subinterfaces per 10-Gigabit Ethernet line module No VLANs: subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1–2147483647; no more than 16,000 PPPoE subinterfaces per 10-Gigabit Ethernet line module subinterface2—Not used Copyright © 2010, Juniper Networks, Inc.
Page 62 Description Interface Specifier Example tunnel Tunnel tunnel-type:tunnel-name[.subinterface] tunnel gre:boston interface tunnel-type—Type of the tunnel: dvmrp, gre, l2tp, or mpls tunnel-name—Name of the tunnel subinterface—For GRE tunnels, number of the subinterface in the range 1–2147483647 Copyright © 2010, Juniper Networks, Inc.
Page 63: A Commands
CHAPTER 2 A Commands Copyright © 2010, Juniper Networks, Inc.
Page 64: Aaa Accounting Acct-Stop On-Aaa-Failure
Configures AAA to send an Acct-Stop message if a user fails AAA, but RADIUS grants access. The no version returns the parameter to the default of enable. Options enable—Specifies the feature; this is the default setting disable—Disables the feature Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 65: Aaa Accounting Acct-Stop On-Access-Deny
Issues an Acct-Stop message if RADIUS denies access. The no version returns the parameter to the default of disable. Options enable—Specifies the feature disable—Disables the feature; this is the default setting Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 66: Aaa Accounting Broadcast
Broadcasts accounting records for a virtual router to accounting servers of the virtual routers in the specified virtual router group. The no version disables the feature. Options vrGroupName—Name of the virtual router group; a string of up to 32 characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 67: Aaa Accounting Commands
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 68: Aaa Accounting Default
RADIUS relay server subscribers tunnel—Specifies tunnel subscribers accountor—Accounting method: none—Disables accounting radius—Enables RADIUS accounting *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 69: Aaa Accounting Duplication
Release Information Command introduced before JunosE Release 7.1.0. Description Sends duplicate accounting records to the accounting server of a different virtual router. The no version disables the feature. Options routerName—Virtual router name Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 70: Aaa Accounting Exec
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 71: Aaa Accounting Immediate-Update
(ACK or timeout) for the Acct-Start message. The no version restores the default condition, disabling immediate updates. Options enable—Specifies the feature disable—Disables the feature; this is the default setting Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 72: Aaa Accounting Interval
Use the aaa service accounting interval and aaa user accounting interval commands to configure default accounting intervals for services and users. Options period—Accounting interval in minutes in the range 10–1440, which sets the time period between accounting updates Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 73: Aaa Accounting Statistics
The no version restores the default setting in which the router collects full statistics. Options volume-time—Collects a full complement of statistics from each connection; the default setting time—Collects only uptime status for each connection Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 74: Aaa Accounting Suppress Null-Username
The no version enables accounting records to be generated for all users, including those who do not have usernames. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 75: Aaa Accounting Vr-Group
A group must contain at least one virtual router. The no version deletes the accounting virtual router group. Options vrGroupName—Name of the virtual router group; a string of up to 32 characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 76: Aaa Authentication Default
PPP subscribers only radius—Enables RADIUS for authentication *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 77: Aaa Authentication Enable Default
RADIUS authentication tacacs+—Use TACACS+ authentication *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 78: Aaa Authentication Login
RADIUS authentication tacacs+—Use TACACS+ authentication *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 79: Aaa Authorization
TACACS+ security daemon *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 80: Aaa Authorization Config-Commands
The no version disables AAA configuration command authorization. NOTE: Using the no version can potentially reduce the amount of administrative control on configuration commands. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 81: Aaa Delimiter
You can specify up to eight characters. The default domain name delimiter is @. The default realm name delimiter is NULL (no character). In this case, realm parsing is disabled (having no delimiter disables realm parsing). Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 82: Aaa Dhcpv6-Delegated-Prefix Delegated-Ipv6-Prefix
Delegated-IPv6-Prefix attribute for DHCPv6 Prefix Delegation. Otherwise, the Framed-IPv6-Prefix attribute will be used for both IPv6 Neighbor Discovery router advertisements and DHCPv6 Prefix Delegation. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 83: Aaa Dns
Specifies the IP address of the primary DNS name server. The no version sets the corresponding address to 0. Options primary—Specifies the primary DNS name server secondary—Specifies the secondary DNS name server ipAddress—IP address of the name server Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 84: Aaa Domain-Map
0–32000 ipAddress—IP address of the local interface ipMask—IPv4 address mask of the local interface Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 85: Aaa Duplicate-Address-Check
NOTE: To use this command, you must have a B-RAS license. Run the license b-ras command and enter your password. Options enable—Specifies the feature; this is the default disable—Disables the feature Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 86: Aaa Duplicate-Prefix-Check
IPv6 prefix checking by AAA is disabled by default . The default version restores the default condition. The no version disables the duplicate IPv6 prefix-check capability. Options enable—Specifies the feature disable—Disables the feature; this is the default Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 87: Aaa Intf-Desc-Format Include
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 88: Aaa Ipv6-Dns
Specifies the IPv6 address of the primary DNS name server. The no version sets the corresponding address to 0 (or ::). Options primary—Specifies the primary DNS name server secondary—Specifies the secondary DNS name server ipv6Address—IPv6 address of the name server Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 89: Aaa Ipv6-Nd-Ra-Prefix Framed-Ipv6-Prefix
Delegated-IPv6-Prefix attribute for Prefix Delegation. This warning message is displayed only if you configured the logging severity level as warning for the aaaServerGeneral logging event category. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 90: Aaa Local Database
Options databaseName—Name of the user database; up to 32 characters; the name default is recognized as the default user database Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 91: Aaa Local Select Database
Assigns the local user database that the virtual router uses for local authentication. The no version restores the default setting, which uses the default local user database for local authentication. Options databaseName—Name of the local user database Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 92: Aaa Local Username
Configuration mode. The no version deletes the user entry from the specified local user database. Options userName—User name of the subscriber databaseName—Name of the local user database; database name default configures the username in the default local user database Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 93: Aaa New-Model
Syntax [ no ] aaa new-model Release Information Command introduced before JunosE Release 7.1.0. Description Specifies AAA authentication for Telnet sessions. The no version restores simple authentication (login and password). Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 94: Aaa Parse-Direction
When the router reaches a domain delimiter, it uses anything to the right of the delimiter as the domain. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 95: Aaa Parse-Order
When the router reaches a realm delimiter, it uses anything to the left of the delimiter as the domain name. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 96: Aaa Profile
Command introduced before JunosE Release 7.1.0. Description Creates a new AAA profile to allow mapping to AAA services. The no version removes the profile. Options profileName—Profile name of up to 32 characters Mode AAA Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 97: Aaa Qos Downstream-Rate
Enables the QoS downstream rate application to shape VLANs or ATM VCs based on downstream rates obtained from the Actual-Data-Rate-Downstream [26-130] DSL Forum VSA. The no version returns the parameter to the default of disabled. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 98: Aaa Route-Download
1–4294967295; default is name—Name of router used for route-download requests; default is the router hostname password—Password used for route-download requests time—Time the download operation is restarted each day, in 24-hour format (hh:mm:ss) Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 99: Aaa Route-Download Now
There is no no version. Options force—Interrupts any in-progress route-download operation and immediately starts a new download. adjust-scheduler—Resets the download scheduler to use this download as the start time for synchronizing download counts Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 100: Aaa Route-Download Suspend
[ no ] aaa route-download suspend Release Information Command introduced in JunosE Release 8.1.0. Description Temporarily suspends the RADIUS route-download server operation. The no version stops the suspend specification and restores the route download operation. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 101: Aaa Service Accounting Interval
Options period—Accounting interval in minutes in the range 10–1440, which sets the time period between accounting updates for services associated with users on this virtual router; 0 is the default Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 102: Aaa Subscriber Limit Per-Port
Interface Types and Specifiers on page 5 limitValue—Maximum number of subscribers; default value is 0 (zero), which means there is no limit on the number of subscribers Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 103: Aaa Subscriber Limit Per-Vr
Sets the maximum number of active subscribers permitted on the virtual router. The no version returns the limit to the default, 0 (zero). Options limitValue—Maximum number of subscribers; default value is 0 (zero), which means there is no limit on the number of subscribers Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 104: Aaa Timeout
PPP session; if you do not specify the ingress-only keyword, PPP monitors both ingress traffic and egress traffic for the idle timeout period to determine inactivity and subsequent disconnection of an inactive PPP session Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 105: Aaa Tunnel Assignment-Id-Format
Sets the format for the tunnel assignment ID. The no version sets the tunnel assignment ID to the default, assignmentID. Options assignmentId—Configures the format to be assignmentId only client-server-id—Configures the format to be a combination of clientAuthId + serverAuthId + assignmentId Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 106: Aaa Tunnel Calling-Number-Format
(up to 4 bytes) slot (2 bytes) port (1 byte) VPI (3 bytes) VCI (5 bytes) Format for Ethernet interfaces: systemName (up to 4 bytes) slot (2 bytes) port (1 byte) VLAN (8 bytes) Format for serial interfaces: Copyright © 2010, Juniper Networks, Inc.
Page 107 IOAs, adapter is always shown as 0. Slot numbers 0 through 16 are shown as integers in the 2-byte slot field. include-agent-circuit-id—Formats calling number AVP to include only the agent-circuit-id suboption Copyright © 2010, Juniper Networks, Inc.
Page 108 VLAN (4 bytes) Format for Ethernet interfaces that use fixed-adapter-new-field: systemName (up to 4 bytes) slot (2 bytes) adapter (1 byte) port (2 bytes) S-VLAN (4 bytes) VLAN (4 bytes) Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 109: Aaa Tunnel Calling-Number-Format-Fallback
(up to 4 bytes) slot (1 byte) adapter (1 byte) port (1 byte) VPI (3 bytes) VCI (5 bytes) Fallback format for Ethernet interfaces: systemName (up to 4 bytes) slot (1 byte) adapter (1 byte) port (1 byte) VLAN (8 bytes) Copyright © 2010, Juniper Networks, Inc.
Page 110 VLAN (4 bytes) Fallback format for Ethernet interfaces that use fixed-adapter-new-field: systemName (up to 4 bytes) slot (2 bytes) adapter (1 byte) port (2 bytes) S-VLAN (4 bytes) VLAN (4 bytes) Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 111: Aaa Tunnel Client-Name
The no version deletes the client name. Options name—Default tunnel client name; a string of up to 32 characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 112: Aaa Tunnel-Group
In Tunnel Group Configuration mode, you can add up to 31 tunnel definitions. The no version deletes the AAA group tunnel configuration from the router. Options groupName—String of up to 64 characters (no spaces) Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 113: Aaa Tunnel Ignore
The no version negates the command or restores the default of enable. Options nas-port—Configures the tunnel peer's supplied nas-port value nas-port-type—Configures the tunnel peer's supplied nas-port-type value enable—Implements the feature; this is the default setting disable—Disables the feature Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 114: Aaa Tunnel Nas-Port-Method
LAC to LNS NAS port identification transfer mechanism. The no version disables the command. NOTE: Use of this feature is not recommended and continued compatibility cannot be guaranteed. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 115: Aaa Tunnel Password
The no version deletes the password. Options name—Default tunnel password; a string of up to 32 characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 116: Aaa Tunnel Switch-Profile
The no version removes the default tunnel switch profile assignment from the virtual router. Options profileName—Name of the default tunnel switch profile; a string of up to 64 alphanumeric characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 117: Aaa Tunnel Tx-Connect-Speed-Method
QoS actual—Calculates the transmit connect speed of the subscriber's access interface as the lesser of the dynamic-layer2 value or the qos value Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 118: Aaa User Accounting Interval
Options period—Accounting interval in minutes in the range 10–1440, which sets the time period between accounting updates for users on this virtual router; 0 is the default Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 119: Aaa Virtual-Router
AAA broadcast accounting packets. Mode VR Group Configuration Copyright © 2010, Juniper Networks, Inc.
Page 120: Aaa Wins
Specifies the IP address of the WINS name server. The no version sets the corresponding address to 0. Options primary—Specifies the primary WINS name server secondary—Specifies the secondary WINS name server ipAddress—IP address of the name server Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 121: Access-Class In
Command introduced before JunosE Release 7.1.0. Description Restricts incoming connections between a particular virtual terminal line and the addresses in an access list. The no version removes access restrictions. Options listName—Name of the access list Mode Line Configuration Copyright © 2010, Juniper Networks, Inc.
Page 122: Access-List
IP address for destination dstIPHost—Destination host IP address to which the packet is being sent log—Logs an Info event into the ipAccessList log whenever the access-list rule is matched Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 123: Accounting
User Exec terminal sessions on the line level—Privilege level of User Exec mode commands for which accounting information is captured; in the range 0–15 listName—Named method list used to specify how accounting is performed Mode Line Configuration Copyright © 2010, Juniper Networks, Inc.
Page 124: Adapter Accept
0 indicates that the IOA is installed in the right IOA bay (E120 router) or the upper IOA bay (E320 router). 1 indicates that the IOA is installed in the left IOA bay (E120 router) or the lower IOA bay (E320 router). Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 125: Adapter Disable
0 indicates that the IOA is installed in the right IOA bay (E120 router) or the upper IOA bay (E320 router). 1 indicates that the IOA is installed in the left IOA bay (E120 router) or the lower IOA bay (E320 router). Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 126: Adapter Enable
0 indicates that the IOA is installed in the right IOA bay (E120 router) or the upper IOA bay (E320 router). 1 indicates that the IOA is installed in the left IOA bay (E120 router) or the lower IOA bay (E320 router). Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 127: Adapter Erase
0 indicates that the IOA is installed in the right IOA bay (E120 router) or the upper IOA bay (E320 router). 1 indicates that the IOA is installed in the left IOA bay (E120 router) or the lower IOA bay (E320 router). Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 128: Address
IP address (inclusive) of the NAT pool range you are creating endIpAddress—Ending IP address (inclusive) of the NAT pool range you are creating Mode Address Family Configuration (RIP), Domain Map Tunnel Configuration, IP NAT Pool Configuration, Router Configuration (RIP), Tunnel Group Tunnel Configuration Copyright © 2010, Juniper Networks, Inc.
Page 129: Address Area
Interface Types and Specifiers on page 5 areaId—OSPF area ID in IP address format areaIdInt—OSPF area ID as a decimal value in the range 1–4294967295 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 130: Address Authentication Key
8—Indicates the authKey is entered in encrypted form (ciphertext) authkey—Password sent with RIP messages or the key used to encrypt/decrypt RIP messages, depending on the authentication mode set for this interface Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 131: Address Authentication-Key
Interface Types and Specifiers on page 5 0—Indicates the authKey is entered in unencrypted form (plaintext); this is the default option 8—Indicates the authKey is entered in encrypted form (ciphertext) authKey—Password, string of up to 8 characters Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 132: Address Authentication Message-Digest
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 133: Address Authentication Mode
RIP message. keyID—Number identifying the MD5 key. Neighbors must share the MD5 key to decrypt the message and encrypt the response. Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 134: Address Authentication-None
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 135: Address Bfd-Liveness-Detection
BFD packets that can be missed before the BFD session is declared down; number in the range 1–255; default value is 3 Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 136: Address Cost
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 intfCost—Link-state metric cost; a number in the range 0–65535; default value is 10 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 137: Address Dead-Interval
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 deadInterval—Number in the range 0–2147483647 seconds; default value is 40 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 138: Address-Family
For RIP, configures RIP in a specific VRF to exchange IPv4 addresses. For all routing protocols, the no version removes the address family. Options ipv4—Specifies sessions that carry standard IPv4 address prefixes (default) ipv6—Specifies sessions that carry IPv6 address prefixes Copyright © 2010, Juniper Networks, Inc.
Page 139 L2VPN address family; must be issued for each separate L2VPN instance Mode Router Configuration Related Topics Configuring BGP Signaling for L2VPNS and Configuring BGP Signaling for VPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 140: Address Hello-Interval
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 helloInterval—Number in the range 1–65535 seconds; default value is 10 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 141: Address Message-Digest-Key Md5
0—Indicates the msgDigestKey is entered in unencrypted form (plaintext); this is the default option 8—Indicates the msgDigestKey is entered in encrypted form (ciphertext) msgDigestKey—OSPF password; string of up to 16 alphanumeric characters Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 142: Address Network
Interface Types and Specifiers on page 5 broadcast—Sets network type to broadcast non-broadcast—Sets network type to NBMA point-to-point—Sets network type to point-to-point Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 143: Address Passive-Interface
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 144: Address-Pool-Name
Specifies an address pool name to associate with the domain name being configured. The no version removes the pool name. Options poolName—Name of the pool to associate with the domain name Mode Domain Map Configuration Copyright © 2010, Juniper Networks, Inc.
Page 145: Address Priority
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 intfPriority—Priority value, an 8-bit number in the range 1–255; default value is 1 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 146: Address Receive Version
1—Specifies RIP version 1 only 2—Specifies RIP version 2 only 1 2—Specifies RIP version 1 and version 2; the default value 2 1—Specifies RIP version 2 and version 1 off—Turns reception off Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 147: Address Retransmit-Interval
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 retransInterval—Number in the range 0–3600 seconds; default value is 5 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 148: Address Send Version
1—Specifies RIP version 1 only 2—Specifies RIP version 2 only 1 2—Specifies RIP version 1 and version 2 2 1—Specifies RIP version 2 and version 1 off—Turns reception off Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 149: Address Transmit-Delay
Interface Types and Specifiers on page 5 transmDelay—Link-state transmit delay, a number in the range 0–3600 seconds; default value is 1 second Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 150: Adjustment-Factor
QoS adjustment factor: adsl1, adsl2, adsl2+, vdsl, vdsl2, or sds value—QoS adjustment factor applied to upstream or down stream data rates for the DSL type; a percentage in the range 1–100 Mode L2C Configuration Copyright © 2010, Juniper Networks, Inc.
Page 151: Agent Context-Name
(for example, router1, router2, and so on). Use the show snmp agent command to obtain the context name for the virtual router. wildcard—Specifies that the context name is a wildcard value contextNameLimit—Maximum number of agents to be polled Mode SNMP Trigger Configuration Copyright © 2010, Juniper Networks, Inc.
Page 152: Aggregate-Address
32 characters that identifies a route map that filters routes to be suppressed *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 153: Aggregation-Node
Aggregation node number in the range 1–65535 vpValue—ATM VPI number in the range 0–255 svlanValue—S-VLAN ID number in the range 0–4095 Mode Policy Parameter Configuration Related Topics Creating a Classifier Group for a Policy List Copyright © 2010, Juniper Networks, Inc.
Page 154: Aggressive-Mode
Enables aggressive mode negotiation for the tunnel. The no version restores the default, no aggressive mode. Options accepted—Accepts aggressive mode when proposed by peers requested—Requests aggressive mode when negotiating with peers required—Only requests and accepts aggressive mode when negotiating with peers Mode IKE Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 155: Allow
Command introduced before JunosE Release 7.1.0. Description Specifies the domain names that are to be allowed access to AAA authentication. The no version negates the command. Options domainName—Name of the domain; maximum of 64 characters Mode AAA Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 156: Append-After
(adjacent) to the previous node in the path. If loose is not configured, the configuration defaults to strict. Strict indicates that the node is directly connected to the previous node. Mode Explicit Path Configuration Copyright © 2010, Juniper Networks, Inc.
Page 157: Application
DVMRP traffic. gre—Secures GRE traffic. l2tp—Secures L2TP traffic; this is the default application l2tp-nat-passthrough—Secures L2TP traffic and also allows clients to connect from behind NAT devices that support IPSec passthrough Mode IPSec Transport Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 158: Aps Events
APS protection signal byte failures switchover—Configures notification of APS switchovers *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 159: Aps Force
The no version allows the specified interface to resume operation. Options channelNumber—One of the following channel numbers: 0—Switches from the protect interface back to the working interface 1—Switches from the working interface to the protect interface Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 160: Aps Group
Assigns an interface to an APS/MSP group. The no version removes a group of APS/MSP interfaces. Options groupName—Name of the APS/MSP group to which the active and standby interfaces belong; string of up to 32 characters Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 161: Aps Lockout
Options 0—Specifies the channel number that identifies the protect interface; because the protect interface is always assigned channel number 0, this is the only valid option Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 162: Aps Manual
The no version allows the specified working interface to resume the active role. Options channelNumber—One of the following channel numbers: 0—Switches from the protect interface back to the working interface 1—Switches from the working interface to the protect interface Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 163: Aps Protect
Options 0—Specifies the channel number that identifies the protect interface; because the protect interface is always assigned channel number 0, this is the only valid option Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 164: Aps Revert
Configures the APS/MSP group to operate in revertive mode. The no version restores the default setting, nonrevertive mode. Options minutes—Number of minutes in the range 5–12 at which the interface resumes the active role after that interface becomes available Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 165: Aps Unidirectional
Command introduced before JunosE Release 7.1.0. Description Configures the APS/MSP group to operate in unidirectional mode, the default setting. The no version configures the APS/MSP group to operate in bidirectional mode. Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 166: Aps Working
Configures an interface as a working interface. The no version removes the configuration. Options 1—Channel number that identifies the working interface; because the working interface is always assigned channel number 1, this is the only valid option Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 167: Area
{ areaId | areaIdInt } Release Information Command introduced before JUNOSe Release 7.1.0. Description This command has only a no version. See the no area command for a complete description. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 168: Area-Authentication
IS-IS level 1 CSNPs and PSNPs is disabled. Options csnp—Enables authentication of IS-IS level 1 complete sequence number PDUs (CSNPs) psnp—Enables authentication of IS-IS level 1 partial sequence number PDUs (PSNPs) Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 169: Area-Authentication-Key
Options 0—Indicates the authKey is entered in unencrypted form (plaintext); this is the default option 8—Indicates the authKey is entered in encrypted form (ciphertext) authKey—Password, string of up to 8 characters Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 170: Area Default-Cost
Options areaId—OSPF area ID in IP address format areaIdInt—OSPF area ID as a decimal value 0–4294967295 defaultCost—Stub area's advertised external route cost (cost metric); an integer in the range 0–16777215 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 171: Area-Message-Digest-Key
HH : MM[: SS ]. startGenTime, startGenMonth, startGenDay, startGenYear—Time, month, day, year that the router will start inserting this password into packets. Use military time format HH : MM[: SS ]. Copyright © 2010, Juniper Networks, Inc.
Page 172 HH : MM[: SS ]. stopGenTime, stopGenMonth, stopGenDay, stopGenYear—Time, month, day, year that the router will stop inserting this password into packets. Use military time format HH : MM[: SS ]. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 173: Area Nssa
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line no-summary—Restricts T3 summary LSAs from flowing into the NSSA area (T7 external LSAs and T3 default route LSAs are still injected into the area) Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 174: Area Range
(IPv6 only) costValue—Cost value for the specified range of networks in the range 0–65535 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 175: Area Stub
Options areaId—OSPF area ID in IP address format areaIdInt—OSPF area ID as a decimal value in the range 0–4294967295 no-summary—Specifies that the summary LSA not be sent into the stub area Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 176: Area Virtual-Link
Defines an OSPF virtual link. The no version removes the virtual link. Options areaId—OSPF area ID in IP address format areaIdInt—OSPF area ID as a decimal value in the range 0–4294967295 ipAddress—IP address associated with the virtual link neighbor Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 177: Area Virtual-Link Authentication-Key
8—Indicates the key is entered in encrypted form (ciphertext) key—Password to be used by neighbors; string of up to 16 alphanumeric characters. All neighboring routers on the same network must have the same password. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 178: Area Virtual-Link Authentication Message-Digest
MD5 key intact. Options areaId—OSPF area ID in IP address format areaIdInt—OSPF area ID as a decimal value in the range 0–4294967295 ipAddress—IP address of the virtual link neighbor Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 179: Area Virtual-Link Authentication-None
Specifies that no authentication is to be used for the virtual link. The no version has no effect. Options areaId—OSPF area ID in IP address format areaIdInt—OSPF area ID as a decimal value in the range 0–4294967295 ipAddress—IP address of the virtual link neighbor Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 180: Area Virtual-Link Dead-Interval
ID in IP address format areaIdInt—OSPF area ID as a decimal value in the range 0–4294967295 ipAddress—IP address of the virtual link neighbor deadInterval—Integer in the range 0–2147483647 seconds; default value is 40 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 181: Area Virtual-Link Hello-Interval
ID in IP address format. areaIdInt—OSPF area ID as a decimal value in the range 0–4294967295 ipAddress—IP address associated with the virtual link neighbor helloInterval—Integer in the range 1–65535 seconds; default value is 10 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 182: Area Virtual-Link Message-Digest-Key Md5
8—Indicates the msgDigestKey is entered in encrypted form (ciphertext) msgDigestKey—Password to be used by neighbors; string of up to 16 alphanumeric characters. All neighboring routers on the same network must have the same password. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 183: Area Virtual-Link Retransmit-Interval
ID as a decimal value in the range 0–4294967295 ipAddress—IP address of the virtual link neighbor retransmInterval—LSA retransmit interval; an integer in the range 0–3600 seconds; default value is 5 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 184: Area Virtual-Link Transmit-Delay
ID as a decimal value in the range 0–4294967295 ipAddress—IP address associated with the virtual link neighbor transmDelay—LSA transmit delay; an integer in the range 0–3600 seconds; default value is 1 second Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 185: Arp
VPLS instance forwards ARP packets deny—Specifies that the subscriber interface associated with the bridge group or VPLS instance filters ARP packets Mode Global Configuration, Subscriber Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 186: Arp Spoof-Check
ARP packets received on a major IP interface or a subinterface to identify and discard spoofed ARP packets. The no version disables checking for spoofed ARP packets received on the interface. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 187: Arp Timeout
ATM 1483. The default value is 21600 seconds (6 hours). Use the show configuration command to display the current value. The no version restores the default value. Options timeoutVal—Time in seconds that an entry remains in the ARP cache Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 188: Assured-Rate
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Scheduler Profile Configuration Related Topics Configuring an Assured Rate for a Scheduler Node or Queue Configuring a Basic Parameter Definition for QoS Administrators Copyright © 2010, Juniper Networks, Inc.
Page 189: Atm
0–4294967295 Kbps scr—Sustained cell rate in the range 0–4294967295 Kbps mbs—Maximum burst size in the range 0–4294967295 Kbps Mode Domain Map Configuration Copyright © 2010, Juniper Networks, Inc.
Page 190: Atm Aal5 Description
Assigns a text description or alias to an ATM AAL5 interface. The no version removes the text description or alias. Use the show atm aal5 interface command to display the text description. Options name—Alias for the AAL5 interface; up to 32 characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 191: Atm Aal5 Shutdown
[ no ] atm aal5 shutdown Release Information Command introduced before JunosE Release 7.1.0. Description Sets the administrative state of an ATM AAL5 interface to disabled. The no version enables a disabled interface. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 192: Atm Aal5 Snmp Trap Link-Status
[ no ] atm aal5 snmp trap link-status Release Information Command introduced before JunosE Release 7.1.0. Description Enables SNMP link status traps on the AAL5 layer on a per-interface basis. The no version disables the traps. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 193: Atm Atm1483 Advisory-Rx-Speed
[38] to the LNS. The no version restores the default behavior, in which the RX speed is not sent to the LNS. Options speed—Speed in the range 0–2147483647 kbps Mode Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 194: Atm Atm1483 Auto-Configure
1–86400 seconds (24 hours); default value is 1 second maxValue—Maximum lockout time in the range 1–86400 seconds (24 hours); default value is 300 seconds (5 minutes) none—Disables lockout for the specified dynamic encapsulation type Mode Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 195: Atm Atm1483 Description
Assigns a text description or alias to an ATM 1483 interface. The no version removes the text description or alias. Use theshow atm subinterface command to display the text description. Options name—Text string or alias for the ATM 1483 interface; up to 255 characters Mode Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 196: Atm Atm1483 Export-Subinterface-Description
Command introduced before JunosE Release 7.1.0. Description Exports ATM 1483 subinterface descriptions to the line module. The no version restores the default behavior, where ATM 1483 subinterface descriptions are not sent to the line module. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 197: Atm Atm1483 Mtu
Sets the MTU size for an ATM 1483 subinterface. The no version restores the default MTU size of 9180. Options size—Maximum number of packet transmissions permitted on an ATM 1483 subinterface; in the range 256–9180; default value is 9180 Mode Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 198: Atm Atm1483 Profile
ATM 1483 subinterface. The no version removes the profile assignment for the upper interface type. Options upperInterfaceType—One of the following dynamic encapsulation types: bridgedEthernet pppoe profileName—Profile name of up to 80 characters Mode Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 199: Atm Atm1483 Shutdown
[ no ] atm atm1483 shutdown Release Information Command introduced before JunosE Release 7.1.0. Description Sets the administrative state of an ATM 1483 subinterface to disabled. The no version enables a disabled subinterface. Mode Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 200: Atm Atm1483 Snmp Trap Link-Status
[ no ] atm atm1483 snmp trap link-status Release Information Command introduced before JunosE Release 7.1.0. Description Enables SNMP link status traps on the ATM1483 layer. The no version disables the traps. Mode Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 201: Atm Atm1483 Subscriber
Mode Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 202: Atm Auto-Configuration
The no version disables auto configuration and sets the ILMI parameters to the UNI version configured using the atm uni-version command, which has a default value of UNI 4.0. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 203: Atm Bulk-Config
(inclusive) of the VC subrange you are configuring *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 204: Atm Bulk-Config Modify
(inclusive) of the VC subrange you are configuring vciStart—Starting virtual circuit identifier (inclusive) of the VC subrange you are configuring vciEnd—Ending virtual circuit identifier (inclusive) of the VC subrange you are configuring Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 205: Atm Bulk-Config Shutdown
(inclusive) of the VC subrange you are configuring vciStart—Starting virtual circuit identifier (inclusive) of the VC subrange you are configuring vciEnd—Ending virtual circuit identifier (inclusive) of the VC subrange you are configuring Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 206: Atm Cac
0–2147482647 Kbps; default value is 0 ubrWeight—Bandwidth associated with UBR and UBR-PCR connections in the range 0–2147482647 Kbps; default value is 0 Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 207: Atm Cell-Packing
ATM cells in the packet is fewer than the specified maximum number of cells per packet. Mode Subinterface Configuration Related Topics Configuring an MPLS Pseudowire with VCC Cell Relay Encapsulation in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 208: Atm-Cell-Mode
Accounts for the ATM cell tax in rate calculationsfor interface types that support rate-limiting and are stackable over ATM. The no version restores the default, which uses the frame size with the layer 2 header included. Mode Policy List Configuration Related Topics Enabling ATM Cell Mode Copyright © 2010, Juniper Networks, Inc.
Page 209: Atm Classifier-List
0–15 clpValue—Value of the CLP, 0 or 1 classifierNumber—Index of the classifier control list entry to be deleted Mode Global Configuration Related Topics Creating or Modifying Classifier Control Lists for ATM Policy Lists Copyright © 2010, Juniper Networks, Inc.
Page 210: Atm Class-Vc
VC ranges that are dynamically created from this profile. The no version removes the VC class association with the base profile. Options vcClassName—Name of the VC class configured with the vc-class atm command Mode Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 211: Atm Clock Internal
Options internalSource—One of the following: module—Specifies that the internal clock is from the line module chassis—Specifies that the internal clock is from the configured router clock Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 212: Atm Description
The no version removes the text description or alias. Options name—Text string or alias of up to 255 characters; can include the # (pound sign) character Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 213: Atm Dos-Protection-Group
Attaches an ATM denial of service (DoS) protection group to an interface. The no version removes the DoS protection group. Options groupName—Name of the DoS protection group; string of up to 31 alphanumeric characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 214: Atm Framing
ATM direct mapping for an E3 interface g751plcp—G.751 PLCP mapping for an E3 interface (default for E3) m23adm—M23 ATM direct mapping for a DS3 (T3) interface m23plcp—M23 with PLCP framing for a DS3 (T3) Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 215: Atm Ilmi-Enable
Chapter 2: A Commands atm ilmi-enable Syntax [ no ] atm ilmi-enable Release Information Command introduced before JunosE Release 7.1.0. Description Enables ILMI on the interface. The no version removes the ILMI PVC. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 216: Atm Ilmi-Keepalive
Enables generation of ILMI keepalive messages on the router, affecting the operational state of the ATM interface. The no version disables the generation of keepalive messages. Options seconds—Number in the range 0–4294967295; the interval in seconds between two consecutive ILMI keepalive requests Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 217: Atm Lbo
Specifies the cable length (line build-out) for the ATM T3 or E3 interface. The length of cable determines power requirements. The no version restores the default value. Options long—Specifies cable length in the range 226–450 feet short—Specifies cable length in the range 0–225 feet (the default) Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 218: Atm Mcpt-Timers
100–4095; default value is 500 timer3—Number of microseconds in the range 100–4095; default value is 1000 Mode Global Configuration Related Topics Configuring an MPLS Pseudowire with VCC Cell Relay Encapsulation in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 219: Atm Oam
VC as a sink point (cell receiver) source—Enables this VC as the source point (cell generator) both—Enables this VC as both a sink point and a source point Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 220: Atm Oam Flush
ATM interface. The no version disables OAM flush on the interface. Options alarm-cells—Causes the router to ignore only AIS and RDI cells and to accept all other OAM cells Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 221: Atm Oam Loopback-Location
Sets the location ID of the ATM interface. The no version returns the loopback location to the default setting of all 1s (ones). Options locationID—Value of the four-octet long location ID of the ATM interface Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 222: Atm Policy
Mode Interface Configuration Related Topics Setting a Statistics Baseline for Policies Copyright © 2010, Juniper Networks, Inc.
Page 223: Atm Policy-List
Attaching this policy list to an interface filters all packets on that interface. The no version removes a policy list. Options policyName—Name of the policy list; a maximum of 40 characters Mode Global Configuration Related Topics Creating Policy Lists for ATM Copyright © 2010, Juniper Networks, Inc.
Page 224: Atm Pvc
PVC. The allowable numeric range depends on the line module capabilities and current configuration. The VPI and VCI cannot both be set to 0; if one is 0, the other cannot be 0. Copyright © 2010, Juniper Networks, Inc.
Page 225 ARP refresh rate in minutes; 15 minutes is the default cc—Enables CC cells on the PVC; you can enable CC cells only on data circuits, not on control circuits, such as ILMI or signaling circuits Copyright © 2010, Juniper Networks, Inc.
Page 226 Interface Configuration, Profile Configuration, Subinterface Configuration Related Topics Configuring an MPLS Pseudowire with VCC Cell Relay Encapsulation, Configuring Local ATM Cross-Connects with AAL5 Encapsulation, and Configuring MPLS LSPs for L2VPNs in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 227: Atm Shutdown
Chapter 2: A Commands atm shutdown Syntax [ no ] atm shutdown Release Information Command introduced before JunosE Release 7.1.0. Description Administratively disables an ATM interface. The no version enables a disabled interface. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 228: Atm Snmp Trap Link-Status
[ no ] atm snmp trap link-status Release Information Command introduced before JunosE Release 7.1.0. Description Enables SNMP link status traps on the ATM layer on a per-interface basis. The no version disables the traps. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 229: Atm Sonet Stm-1
Release Information Command introduced before JunosE Release 7.1.0. Description Sets the mode of operation on the physical interface to SDH STM-1. The no version restores the default value, SONET STS-3c operation. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 230: Atm Uni-Version
Release Information Command introduced before JunosE Release 7.1.0. Description Specifies the UNI version the interface should use. There is no no version. Options versionNumber—UNI version number: 3.0, 3.1, or 4.0 Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 231: Atm Vc-Per-Vp
VCs and VP tunnels must not exist when you issue this command. If they do, you must delete the VC and VP tunnel configuration before you issue this command. Options vcCount—Number of virtual circuits per virtual path Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 232: Atm Vp-Description
The no version restores the default value, a null string. Options vpi—Virtual path identifier number in the range 0–255 description—Text string or alias for the specified VPI; up to 32 characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 233: Atm-Vp Qos-Parameter
VP qosParameterInstanceValue—Number of the scheduler rate for the parameter instance; the default value is the minimum value defined in the parameter definition Mode Interface Configuration Related Topics Creating Parameter Instances Copyright © 2010, Juniper Networks, Inc.
Page 234: Atm-Vp Qos-Profile
PVC; number in the range 0–255 qosProfileName—Name of the QoS profile that you want to attach to the VP Mode Interface Configuration Related Topics Attaching a QoS Profile to an Interface Copyright © 2010, Juniper Networks, Inc.
Page 235: Atm Vp-Tunnel
Certain line modules may have minimum rates for VP tunnels. Using a rate of 0 configures a shapeless tunnel (a tunnel with no rate) that is used for VP shaping in the SAR. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 236: Authentication
Specifies the authentication method to use in the IKE policy. The no version restores the default, preshared keys. Options rsa-sig—Specifies RSA signature as the authentication method pre-share—Specifies preshared keys as the authentication method Mode IKE Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 237: Authentication Key
8—Indicates the authKey is entered in encrypted form (ciphertext) authkey—Password sent with RIP messages or the key used to encrypt/decrypt RIP messages, depending on the authentication mode set for this remote-neighbor interface. Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 238: Authentication-Key
0—Indicates the authKey is entered in unencrypted form (plaintext); this is the default option 8—Indicates the authKey is entered in encrypted form (ciphertext) authKey—Password; string of up to 8 characters Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 239: Authentication Message-Digest
Syntax authentication message-digest Release Information Command introduced before JunosE Release 7.1.0. Description Specifies that MD5 authentication is used for the OSPF remote-neighbor interface. There is no no version. Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 240: Authentication Mode
RIP message with MD5 message-digest algorithms keyID—Number identifying the MD5 key in the range 1–255; remote neighbors must share the MD5 key to decrypt the message and encrypt the response Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 241: Authentication-None
Syntax authentication-none Release Information Command introduced before JunosE Release 7.1.0. Description Specifies that no authentication is to be used for the OSPF remote-neighbor interface. There is no no version. Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 242: Authorization
0–15 authorListName—Name of an authorization method list of up to 32 characters; if no methods list is specified, the default is used Mode Line Configuration Copyright © 2010, Juniper Networks, Inc.
Page 243: Authorization Change
Service Manager attributes, from the RADIUS server. The no version restores the default, in which support for RADIUS-initiated change-of-authorization messages is disabled on the router. Mode RADIUS Configuration Related Topics Configuring RADIUS-Based Mirroring Copyright © 2010, Juniper Networks, Inc.
Page 244: Auth-Router-Name
Assigns an access virtual router. The no version restores the default router. NOTE: This command replaces the deprecated router-name command, which may be removed completely in a future release. Options routerName—Name of the virtual router; string of 1–32 alphanumeric characters Mode Domain Map Configuration Copyright © 2010, Juniper Networks, Inc.
Page 245: Auto-Configure
1 second maxValue—Maximum lockout time in the range 1–86400 seconds (24 hours); default value is 300 seconds (5 minutes) none—Disables lockout for the specified dynamic encapsulation type Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 246: Auto-Configure Atm1483
Command introduced before JunosE Release 7.1.0. Description Configures the static ATM AAL5 interface to support autodetection of an ATM 1483 dynamic encapsulation type. The no version terminates autodetection of the ATM 1483 encapsulation type. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 247: Auto-Configure Vlan
Release Information Command introduced in JunosE Release 7.1.0. Description Configures the static VLAN major interface to support autodetection of a dynamic VLAN subinterface. The no version terminates autodetection of the VLAN subinterface. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 248: Auto-Cost Reference-Bandwidth
Controls how OSPFv3 calculates default metrics for the interface. The no version assigns cost based only on the interface type. Options refBw—Bandwidth in megabits per second in the range 1–4294967; default value is Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 249: Automatic-Virtual-Link
Chapter 2: A Commands automatic-virtual-link Syntax [ no ] automatic-virtual-link Release Information Command introduced before JunosE Release 7.1.0. Description Enables or disables automatic virtual link configuration. The no version disables an automatic virtual link. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 250: Auto-Summary
Command introduced before JunosE Release 7.1.0. Description Reenables the automatic summarization of routes redistributed into BGP to their natural network masks. Automatic summarization is enabled by default. The no version disables automatic summarization. Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 251: Average-Length-Exponent
Specifies the exponent used to weight the average queue length over time, controlling WRED responsiveness. The no version negates the average-length-exponent. Options exponent—Total average queue length (TAQL) coefficient Mode Drop Profile Configuration Related Topics Configuring RED Configuring WRED Copyright © 2010, Juniper Networks, Inc.
Page 252: Avp
AVP of the specified type when packets are switched between an inbound LNS session and an outbound LAC session Mode L2TP Tunnel Switch Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 253: Chapter 3 B Commands
CHAPTER 3 B Commands Copyright © 2010, Juniper Networks, Inc.
Page 254: Backup-Address-Pool-Name
16 alphanumeric characters Mode Domain Map Configuration Related Topics Configuring Local Address Servers in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 255: Bandwidth
The no version removes the admission control configuration from the interface. Options bandwidth—Available bandwidth in kilobits per second, a value from 1–10,000,000 Mode Interface Configuration, Subinterface Configuration Related Topics ospf bandwidth Copyright © 2010, Juniper Networks, Inc.
Page 256: Bandwidth Oversubscription
Release Information Command introduced before JunosE Release 7.1.0. Description Allows the line modules to operate below line rate performance. The no version forces the line modules to operate at line rate performance. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 257: Banner
1024 characters; delimited by the first character of the string, which must be repeated at the end of the string and must not occur anywhere else in the string Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 258: Baseline Aaa
There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 259: Baseline Aaa Route-Download
Sets a statistics baseline for route downloads. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 260: Baseline Atm Vp Interface
Options interfaceSpecifier—ATM interface specifier; see Interface Types and Specifiers on page 5 vpi—Virtual path identifier of the PVC. The numeric range depends on the line module capabilities and current configuration. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 261: Baseline Bridge
VPLS instance created with the bridge vpls transport-virtual-router command Mode Privileged Exec Related Topics Setting a Baseline for VPLS Statistics in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 262: Baseline Bridge Interface
Interface Types and Specifiers on page 5 Mode Privileged Exec Related Topics Setting a Baseline for VPLS Statistics in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 263: Baseline Bridge Interface Vpls
To set a statistics baseline for a VPLS network interface, use the baseline bridge interface command. Options vplsName—Name of a VPLS instance created with the bridge vpls transport-virtual-router command Mode Privileged Exec Related Topics Setting a Baseline for VPLS Statistics in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 264: Baseline Clns
There is no no version. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 265: Baseline Cops
There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 266: Baseline Dhcp
There is no no version. Options server—Sets baseline for DHCP proxy server statistics relay—Sets baseline for DHCP relay statistics Mode Privileged Exec Related Topics Setting Baselines for DHCP Statistics Copyright © 2010, Juniper Networks, Inc.
Page 267: Baseline Frame-Relay Interface
Interface Types and Specifiers on page 5 dlci—DLCI number to be used on the specified subinterface to identify a virtual circuit in the range 16–1007 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 268: Baseline Frame-Relay Multilinkinterface
Interface Types and Specifiers on page 5 serial interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 269: Baseline Hdlc Interface
Interface Types and Specifiers on page 5 serial interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 270: Baseline Interface
Interface Types and Specifiers on page 5 vcd—Virtual circuit descriptor; number in the range 1–4294967295; an identifier for the VC in other commands (ATM interfaces only) Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 271: Baseline Ip
Command introduced before JunosE Release 7.1.0. Description Sets the baseline on general IP traffic statistics as the current value. There is no no version. Options vrfName—Name of the VRF; string of 1–32 alphanumeric characters Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 272: Baseline Ip Bgp
Syntax baseline ip bgp Release Information Command introduced before JunosE Release 7.1.0. Description Sets the baseline on all BGP statistics as the current value. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 273: Baseline Ip Dhcp-External
There is no no version. Mode Privileged Exec Related Topics Setting Baselines for DHCP Statistics Copyright © 2010, Juniper Networks, Inc.
Page 274: Baseline Ip Dhcp-Local
Interface Types and Specifiers on page 5 fastEthernet gigabitEthernet tenGigabitEthernet interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 275: Baseline Ip Dvmrp
Sets a baseline for DVMRP statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 276: Baseline Ip Http
Sets a baseline for HTTP local server statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 277: Baseline Ip Igmp
Sets a baseline for IGMP statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 278: Baseline Ip Igmp-Proxy Interface
Sets the baseline on all IGMP statistics by setting the counters for the numbers of queries received and reports sent on the upstream interface to zero. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 279: Baseline Ip Interface
VRF; string of 1–32 alphanumeric characters interfaceType—Interface type; see “Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 280: Baseline Ip Mobile Home-Agent
There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 281: Baseline Ip Nat
Chapter 3: B Commands baseline ip nat Syntax baseline ip nat Release Information Command introduced before JunosE Release 7.1.0. Description Sets a baseline for NAT statistics and counters. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 282: Baseline Ip Ospf
JunosE 11.2.x Command Reference Guide A to M baseline ip ospf Syntax baseline ip ospf Release Information Command introduced before JunosE Release 7.1.0. Description Sets a baseline for OSPF statistics and counters. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 283: Baseline Ip Rip
Sets a statistics baseline for RIP interfaces. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 284: Baseline Ip Tunnel-Reassembly
The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever you retrieve baseline-relative statistics. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 285: Baseline Ip Udp
There is no no version. Options vrfName—Name of the VRF; string of 1–32 alphanumeric characters Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 286: Baseline Ip Vrrp
Sets a statistics baseline for VRRP statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 287: Baseline Ipv6
Sets the baseline on general IPv6 traffic statistics as the current value. Use the udp keyword to set a baseline for UDP statistics. There is no no version. Options udp—Sets a baseline for UDP statistics Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 288: Baseline Ipv6 Dhcpv6-Local
There is no no version. Mode Privileged Exec Related Topics Setting Baselines for DHCP Statistics Copyright © 2010, Juniper Networks, Inc.
Page 289: Baseline Ipv6 Interface
Sets a baseline for IPv6 interface statistics. There is no no version. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 290: Baseline Ipv6 Local Pool
There is no no version. Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 291: Baseline Ipv6 Mld
Sets a baseline for MLD statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 292: Baseline Ipv6 Mld-Proxy Interface
Sets the baseline on all MLD statistics by setting the counters for the numbers of queries received and reports sent on the upstream interface to zero. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 293: Baseline Ipv6 Ospf
[ processId ] Release Information Command introduced before JunosE Release 7.1.0. Description Sets a baseline for OSPFv3 statistics and counters. There is no no version. Options processId—Integer in the range 1–65535 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 294: Baseline Ipv6 Tcp
VRF; string of 1–32 alphanumeric characters localAddress—Local IPv6 address on the router localPort—Local TCP port number on the router remoteAddress—IPv6 address of remote router remotePort—TCP port number on remote router Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 295: Baseline Line Interface Sonet
There is no no version. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 296: Baseline Local Pool
Sets a statistics baseline for the router local address pool statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 297: Baseline Log
UTC (GMT) time; if you do not include this keyword, the router considers the time entered to be local time month—Name of the month in English day—Number of the day in the range 1–31 year—Four-digit number of the year Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 298: Baseline Mpls Interface
By default, the interface counters are baselined at zero. There is no no version. Options interfaceName—Name of interface; up to 15 alphanumeric characters Mode Privileged Exec Related Topics Setting Baselines for Layer 2 Services over MPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 299: Baseline Mpls Label
0–255 vci—Virtual circuit identifier for a label, a value in the range 33–65535 labelValue—Integer identifying a label in the platform label space, a value in the range 16–1048575 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 300: Baseline Mpls Next-Hop
By default, the next-hop counters are baselined at zero. There is no no version. Options nextHopIndex—Number identifying a next hop; displayed by the show mpls forwarding command Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 301: Baseline Mpls Tunnel
By default, the next-hop counters are baselined at zero. There is no no version. Options tunnelName—Name identifying a tunnel; displayed by the show mpls tunnels command Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 302: Baseline Path Interface Sonet
There is no no version. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 303: Baseline Ppp Interface
Gigabit Ethernet interface mlppp—Specifies an MLPPP interface pos—Specifies a POS interface serial—Specifies a serial interface interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 304: Baseline Pppoe Interface
Specifiers on page 5 fastEthernet gigabitEthernet serial—PPPoE is not currently supported on serial interfaces tenGigabitEthernet interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 305: Baseline Radius
Sets a statistics baseline for RADIUS statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 306: Baseline Radius Dynamic-Request
There is no no version. Mode Privileged Exec Related Topics Monitoring Packet Mirroring Overview Copyright © 2010, Juniper Networks, Inc.
Page 307: Baseline Radius Relay
Sets a baseline for RADIUS relay statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 308: Baseline Section Interface Sonet
There is no no version. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 309: Baseline Show-Delta-Counts
[ no ] baseline show-delta-counts Release Information Command introduced before JunosE Release 7.1.0. Description Configures the router to always display the statistics relative to the most recent appropriate baseline. The no version removes the configuration. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 310: Baseline Snmp
Sets a baseline for SNMP statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 311: Baseline Sscc
Sets a baseline for the SRC statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 312: Baseline Suspicious-Control-Flow-Detection Counts
Syntax baseline suspicious-control-flow-detection counts Release Information Command introduced in JunosE Release 7.3.0. Description Sets a baseline for statistics for suspicious control flow detection. There is no no version. Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 313: Baseline Tacacs
Sets a baseline for TACACS+ statistics. The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 314: Baseline Tcp
VRF; string of 1–32 alphanumeric characters localAddress—Local IP or IPv6 address on the router localPort—Local TCP port number on the router remoteAddress—IP or IPv6 address of remote router remotePort—TCP port number on remote router Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 315: Bert
E1 and T1 interfaces only) if specified, the test bit pattern occupies all bits on the link, overwriting the framing bits; if not specified, the test bit pattern occupies only the payload bits Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 316: Bfd Adapt
Enables all BFD sessions to adapt timer intervals on all virtual routers on the router. The no version disables subsequent BFD sessions from adapting timer intervals without resetting any already adapted intervals. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 317: Bgp Advertise-Best-External-To-Internal
BGP selects only one best route for each destination from the complete set of routes; if the best route was received from an internal peer, BGP does not advertise any route to that destination to the internal peers. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 318: Bgp Advertise-Inactive
The no version restores the default state of normal route advertisement, whereby BGP advertises received routes only if they are in the IP forwarding table and are being used to forward traffic, or if synchronization is enabled. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 319: Bgp Always-Compare-Med
[ no ] bgp always-compare-med Release Information Command introduced before JunosE Release 7.1.0. Description Enables the comparison of the MED for paths from neighbors in different ASs. The no version disables the feature. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 320: Bgp Bestpath Med Confed
Specifies that BGP considers the MED when comparing routes originated from different sub-ASs within the confederation to which this BGP speaker belongs. The no version restores the default state, where the MED attribute is not considered. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 321: Bgp Bestpath Missing-As-Worst
MED by causing the missing MED attribute to have a value of infinity. The no version restores the default state, where the missing MED attribute is considered to have a value of zero. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 322: Bgp Client-To-Client Reflection
Restores route reflection from a BGP route reflector to clients. The no version disables client-to-client reflection. By default, BGP reflects routes received from any route reflector client to all other route reflector clients. This command can be used to disable or restore this behavior. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 323: Bgp Cluster-Id
0–4294967295; the cluster ID of this router acting as a route reflector ipAddress—Cluster ID of this router acting as a route reflector specified as an IP address Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 324: Bgp Confederation Identifier
Release Information Command introduced before JunosE Release 7.1.0. Description Configures a BGP confederation identifier. The no version removes a BGP confederation identifier. Options autonomousSystem—Number in the range 1–4294967295; the confederation identifier Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 325: Bgp Confederation Peers
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line filterListName—Name of an AS-path access list; a string of up to 32 characters Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 326: Bgp Dampening
The route map can contain a no dampening clause that determines dampening characteristics. mapTag—Name of the route map; a string of up to 32 alphanumeric characters. Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 327: Bgp Default Ipv4-Unicast
Causes all neighbors subsequently created with the neighbor remote-as or neighbor peer-group commands to be automatically activated in the IPv4 unicast address family. The no version disables the IPv4 unicast address family on all neighbors. Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 328: Bgp Default Local-Preference
The preference is sent to all routers in the local AS. The preferred path is the one with the highest preference value. The no version restores the default setting. Options value—Local preference number in the range 0–4294967295 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 329: Bgp Default Route-Target Filter
Command introduced before JunosE Release 7.1.0. Description Controls whether incoming BGP routes are filtered according to membership in route-target communities. Automatic filtering is enabled by default. The no version disables automatic filtering. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 330: Bgp Enforce-First-As
AS in the AS path of routes received from the peer. If the AS numbers do not match, BGP sends the peer an error message. The no version restores the default condition, which does not perform the AS comparison. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 331: Bgp Fast-External-Fallover
Automatically brings down a BGP session to any adjacent external peer immediately after the link fails (as opposed to waiting for the TCP connection to fail or the hold timer to expire). The no version disables automatic session termination. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 332: Bgp Graceful-Restart
BGP graceful restart capability is stopped. The no version disables the graceful restart capability. NOTE: The E Series router supports graceful restart, both as a receiving peer and a restarting peer. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 333: Bgp Graceful-Restart Path-Selection-Defer-Time-Limit
The period is measured from when the session is detected in a down state. The no version restores the default value, 360 seconds. Options seconds—Integer in the range 1–3600; default value is 600 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 334: Bgp Graceful-Restart Restart-Time
The no version restores the default value, 120 seconds. Options seconds—Integer in the range 1–3600; default value is 120 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 335: Bgp Graceful-Restart Stalepaths-Time
The no version restores the default value, 360 seconds. Options seconds—Integer in the range 1–3600; default value is 360 seconds Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 336: Bgp Log-Neighbor-Changes
Causes BGP to log a message of severity notice to the bgpNeighborChanges log whenever a peer enters or leaves the Established state for any reason. No other messages are logged to the bgpNeighborChanges log. The no version disables this log. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 337: Bgp Maxas-Limit
AS paths are greater than the specified length. The no version halts checking of the AS path length. Options limit—Maximum acceptable length of a received AS path; number in the range 1–1000 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 338: Bgp Redistribute-Internal
BGP route redistribution enabled. This command is not required for IBGP routes within a VRF, for which redistribution is always enabled. The no version restores the default, redistributing only external BGP routes. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 339: Bgp Router-Id
Sets the BGP identifier. The no version restores the router ID as the identifier. Options ipAddress—IP address to be used as the BGP identifier; ignored if present in the no version Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 340: Bgp Shutdown
JunosE 11.2.x Command Reference Guide A to M bgp shutdown Syntax [ no ] bgp shutdown Release Information Command introduced before JunosE Release 7.1.0. Description Administratively disables BGP. The no version reenables BGP. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 341: Bgp Wait-On-End-Of-Rib
Applies to all peers in the route-target address family. The no version restores the default value. Options seconds—Number of seconds BGP wait for End-of-RIB marker, in the range 1–3600; default is 60 seconds Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 342: Boolean-Test
32 alphanumeric characters startup—Specifies not to perform the Boolean comparison when this trigger first becomes active booleanValue—Value in the range -2147483648–2147483647 to use for the Boolean test Mode SNMP Trigger Configuration Copyright © 2010, Juniper Networks, Inc.
Page 343: Boot Backup
The no version removes the setting. Options relFilename—System software file cnfFilename—Name of an existing configuration file (.cnf) scrFilename—Name of an existing script file (.scr) factory-defaults—Specifies that the router reverts to factory default configuration when rebooted Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 344: Boot Config
Manual Commit mode factory-defaults—Specifies that the factory default configuration is to be used for the next reboot. Subsequent reboots revert to the running-configuration settings. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 345: Boot Force-Backup
NOTE: After the router has used the backup settings, the no boot force-backup command is the only way to get the router to use the default settings again. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 346: Boot Hotfix
NOTE: See also the no boot hotfix all-releases command. Options hfixFileName—Name of a hotfix software file (.hfx) on the local file system all-releases—Disarms all hotfixes currently armed for the armed release Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 347: Boot Revert-Tolerance
SRP software crashes; in the range 0–4294967295; default value is 3 time—Time in the range 0–4294967295 seconds in which the set number (count) of crashes occurs; the default setting is 1800 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 348: Boot Revert-Tolerance Never
Syntax boot revert-tolerance never Release Information Command introduced before JunosE Release 7.1.0. Description Sets the boot logic to never revert to the backup release or configuration. There is no no version. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 349: Boot Subsystem
Options backup—Configures a backup setting subsysName—Name of the subsystem to be configured relFileName—Name of system software file to use Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 350: Boot System
Options relFileName—Name of the software release file (.rel) that contains the software release Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 351: Bridge1483 Dos-Protection-Group
Attaches a bridge 1483 denial of service (DoS) protection group to an interface. The no version removes the attachment of the DoS protection group from the interface. Options groupName—Name of the DoS protection group; string of up to 31 alphanumeric characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 352: Bridge1483 Mtu
Ethernet interfaces. The no version restores the default MTU size for bridged Ethernet interfaces, 1518 bytes. Options mtuSize—Maximum allowable size of the MTU, in the range 64–9180 bytes; default value is 1518 Mode Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 353: Bridge1483 Service-Profile
Ethernet interface is created. The IP service profile must be defined in the default virtual router. The no version removes the IP service profile assignment from the interface profile. Options profileName—Name of the IP service profile; maximum of 32 alphanumeric characters Mode Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 354: Bridge
NOTE: Do not assign the bridge group the same name as an existing virtual router configured on the router. Options bridgeGroupName—Name of the bridge group; string of up to 32 alphanumeric characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 355: Bridge Acquire
VPLS instance created with the bridge vpls transport-virtual-router command Mode Global Configuration Related Topics Configuring Optional Attributes for VPLS Instances in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 356: Bridge Address
Interface Types and Specifiers on page 5 discard—Discards (drops) frames sent from or destined for the specified MAC address without further processing Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 357 Chapter 3: B Commands Related Topics Configuring Optional Attributes for VPLS Instances in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 358: Bridge Aging-Time
VPLS instance created with the bridge vpls transport-virtual-router command seconds—Aging time in the range 10–1000000 seconds Mode Global Configuration Related Topics Configuring Optional Attributes for VPLS Instances in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 359: Bridge Crb
The command takes effect for all bridge groups on the router not configured as VPLS instances; you cannot enable CRB for some bridge groups but not for others. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 360: Bridge-Group
VPLS instance can learn, up to the maximum number that the router supports, in the range 0–64000 Mode Interface Configuration, Subinterface Configuration Related Topics Configuring VPLS Network Interfaces in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 361: Bridge Learn
MAC addresses that the bridge group can learn, in the range 0–64000 Mode Global Configuration Related Topics Configuring Optional Attributes for VPLS Instances in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 362: Bridge Route
IP packets mpls—Specifies that the bridge group routes MPLS packets pppoe—Specifies that the bridge group routes PPPoE packets Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 363: Bridge Snmp-Trap Link-Status
VPLS instance created with the bridge vpls transport-virtual-router command Mode Global Configuration Related Topics Configuring Optional Attributes for VPLS Instances in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 364: Bridge Subscriber-Policy
VPLS instance created with the bridge vpls transport-virtual-router command subscriberPolicyName—Name of the subscriber policy specified with the subscriber-policy command Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 365: Bridge Vpls Rd
32 bits if number1 is an AS number; 16 bits if number1 is an IP address Mode Global Configuration Related Topics Configuring VPLS Instances with BGP Signaling in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 366: Bridge Vpls Route-Target
VPNs, where: number1—Autonomous system (AS) number or an IP address number2—Unique integer; 32 bits if number1 is an AS number; 16 bits if number1 is an IP address Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 367 Chapter 3: B Commands Related Topics Configuring VPLS Instances with BGP Signaling in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 368: Bridge Vpls Site-Name Site-Id
VPLS instance becomes the designated VE router for this multihomed site Mode Global Configuration Related Topics Configuring VPLS Instances with BGP Signaling in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 369: Bridge Vpls Site-Range
VPLS domain, in the range 1–65534; default value is 1 Mode Global Configuration Related Topics Configuring VPLS Instances with BGP Signaling in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 370: Bridge Vpls Transport-Virtual-Router
VPLS instance is configured Mode Global Configuration Related Topics Configuring VPLS Instances with BGP Signaling and Configuring VPLS Instances with LDP Signaling in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 371: Broadcast
VPLS instance forwards broadcast packets deny—Specifies that the subscriber interface associated with the bridge group or VPLS instance filters broadcast packets Mode Subscriber Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 372: Buffer-Weight
Sets the buffer weight of the queue. The no version returns the queue to its default buffer weight. Options bufferWeight—Range 1–63; default value is 8 Mode Queue Profile Configuration Related Topics Configuring Queue Profiles to Manage Buffers and Thresholds Copyright © 2010, Juniper Networks, Inc.
Page 373: Bulkstats
Chapter 3: B Commands bulkstats Syntax no bulkstats Description This command has only a no version. See the no bulkstats command for a complete description. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 374: Bulkstats Collector
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 375: Bulkstats File-Format Endofline-Lf
Removes the carriage return (CR) and leaves only a line feed (LF) at the end of each line in the bulkstats file. The no version returns the end of line format to the default, CR and Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 376: Bulkstats Interfaces Description-Format Common
Command introduced before JunosE Release 7.1.0. Description Enables the conventional industry method of encoding the SNMP ifDescr object that the bulkstats application reports. The no version returns the encoding method to a proprietary encoding scheme. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 377: Bulkstats Interfaces Rfc1213
[ no ] bulkstats interfaces rfc1213 Release Information Command introduced before JunosE Release 7.1.0. Description Enables RFC 1213 interface numbering mode on bulkstats. The no version disables RFC 1213 interface numbering mode on bulkstats. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 378: Bulkstats Interface-Type
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line collectorIndex—Number in the range 1–65535 that identifies the particular data collector. Always specify this option if you defined more than one collector. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 379: Bulkstats Receiver Remote-Name
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 380: Bulkstats Schema
Description Configures the schema for collecting bulk statistics. The no version removes the schema. Options schemaIndex—Identifier for the schema in the range 1–65535 collectorIndex—Identifier for the collector in the range 1–65535 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 381: Bulkstats Schema Subtree
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 382: Bulkstats Schema Subtree Policy
—Retrieves statistics based on color-coded tags applied by a policy *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 383: Bulkstats Schema Subtree Qos
QoS schema to export the number of packets of green traffic that was dropped on this queue parent-shaping-rate—Configures QoS schema to export the shaping rate enabled on the parent interface in the scheduling hierarchy Copyright © 2010, Juniper Networks, Inc.
Page 384 *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Related Topics Configuring SNMP in JunosE System Basics Configuration Guide QoS Statistics Overview Copyright © 2010, Juniper Networks, Inc.
Page 385: Bulkstats Traps
Configures the bulkstats traps. The no version disables the trap. Options nearly-full—Specifies a percentage less than 100 percent threshold—Percentage less than 100 percent; if not specified, defaults to 99 percent full—100 percent Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 386: Bulkstats Virtual-Router-Group
1 to the maximum number of routers supported in the system collectorIndex—Number that identifies the particular data collector, in the range 1–65535 VRnames—List of virtual router names Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 387: Bundled-Group-Id
NOTE: We recommend that you assign a bundled group identifier for bundled sessions only when you are certain that endpoint discriminators are unavailable to identify bundle membership. Options bundledGroupID—Identifier for a bundled group in the range 0–4294967295 Mode L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 388: Bundled-Group-Id-Overrides-Mlppp-Ed
The no version removes the override. NOTE: We strongly recommend that you use this command only with the support of JTAC. Mode L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 389: Chapter 4 C Commands
CHAPTER 4 C Commands Copyright © 2010, Juniper Networks, Inc.
Page 390: Cache Entries
Sets the number of entries in the aggregation cache. The no version sets the number of entries to the default value. Options entryNumber—Number of entries in the aggregation cache in the range 1024—524288; default value is 4096 Mode Flow Cache Configuration Copyright © 2010, Juniper Networks, Inc.
Page 391: Cache Timeout
Description Sets the active and inactive aging timers. The no version resets the default values. Options activeTimer—Active aging timer in the range 1—60 inactiveTimer—Inactive aging timer in the range 10—600 Mode Flow Cache Configuration Copyright © 2010, Juniper Networks, Inc.
Page 392: Cablelength
Command introduced before JunosE Release 7.1.0. Description Specifies the length of the cable, which determines power requirements. The no version uses the default value, 0 feet. Options length —Cable length in the range 0–450 feet Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 393: Cbr
UBR without a PCR, in the VC class. Options pcr—Peak cell rate, in Kbps, in the range 1–149760 (for OC3 ATM modules) or 1–599040 (for OC12 ATM modules) Mode ATM VC Configuration, ATM VC Class Configuration Copyright © 2010, Juniper Networks, Inc.
Page 394: Channelized
Command introduced before JunosE Release 7.1.0. Description Configures a port on the CT3/T3-F0 line module and associated I/O module to support channelized T3 operation. The no version configures the port for unchannelized operation. Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 395: Check-Disk
Boot mode, because disk0 cannot be in an unmounted state in a router outside of Boot mode disk1—Specifies flash card in slot 1 of the SRP module; supported only on the E120 router and the E320 router Mode Boot, Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 396: Check-Vpn-Next-Hops
Enables a BGP speaker to take the reachability of the next hop on received VPNv4 or VPNv6 routes into account when it determines the best route to a prefix. Checking the reachability is disabled by default. The no version explicitly disables reachability checking. Mode Address Family Configuration Copyright © 2010, Juniper Networks, Inc.
Page 397: Classifier-Group
You must use classifier-group *. Also, secure policy lists do not support the precedence keyword. externalParentGroupName—External parent group name parameterName—Parameter name Mode Policy List Configuration Related Topics Creating a Classifier Group for a Policy List Configuring CLI-Based Mirroring Copyright © 2010, Juniper Networks, Inc.
Page 398: Class-Int
PVC attributes to their systemwide default values, or to the values set in the associated VC class with the next highest order of precedence. Options vcClassName—Name of the VC class configured with the vc-class atm command Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 399: Class-Vc
Issuing this command applies the set of attributes in the specified VC class to the ATM data PVC. The no version removes the VC class association with the ATM PVC. Options vcClassName—Name of the VC class configured with the vc-class atm command Mode ATM VC Configuration Copyright © 2010, Juniper Networks, Inc.
Page 400: Cleanup-Timeout-Factor
Specifies the number of refresh messages that can be lost before the PATH or RESV state is ended. The no version restores the default value, 3. Options lostRefreshes—Number of lost refresh messages Mode RSVP Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 401: Clear Access-List
Command introduced before JunosE Release 7.1.0. Description Clears counters for entries in IP access lists. There is no no version. Options accessListName—Name of the access list; string of 1–32 alphanumeric characters Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 402: Clear Arp
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 *—Clears all dynamic ARP entries Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 403: Clear Bfd Adapted-Intervals
Syntax clear bfd adapted-intervals Release Information Command introduced in JunosE Release 7.3.0. Description Resets adapted timer intervals for all BFD sessions on the router. There is no no version. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 404: Clear Bfd Session
Restarts all BFD sessions or a specified BFD session. There is no no version. Options ipAddress—IP address of the destination to which the session has been established discriminatorID—Unique system-wide identifier for the BFD session; integer in the range 1–4294967295 Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 405: Clear Bgp Ipv6
BGP peer group to clear *—Clears all connections vrfName—Name of a virtual routing and forwarding instance to clear soft—Specifies soft reconfiguration in—Triggers inbound soft reconfiguration out—Triggers outbound soft reconfiguration Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 406: Clear Bgp Ipv6 Dampening
NLRI (RT-MEM-NLRI), in the format asNumber: extendedCommunity (for example, 320:320:524 or 320:50.2.3.4:524) vrfName—Name of a virtual routing and forwarding instance to clear unicast—Clears the unicast routing table; the default option multicast—Clears the multicast routing table Copyright © 2010, Juniper Networks, Inc.
Page 407 Chapter 4: C Commands vpnv6—Clears the VPNv6 unicast routing and forwarding table ipv6Prefix—IPv6 network for which to clear dampening information Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 408: Clear Bgp Ipv6 Dynamic-Peers
BGP neighbor to clear ipv6Address—IPv6 address of identified BGP neighbor to clear peerGroupName—Name of a BGP peer group to clear *—Clears all connections vrfName—Name of a virtual routing and forwarding instance to clear Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 409: Clear Bgp Ipv6 Redistribution
Command introduced before JunosE Release 7.1.0. Description Clears all IPv6 routes that have been redistributed into BGP. There is no no version. Options unicast—Clears the unicast routing table; the default option multicast—Clears the multicast routing table Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 410: Clear Bgp Ipv6 Wait-End-Of-Rib
BGP neighbor to clear ipv6Address—IPv6 address of identified BGP neighbor to clear peerGroupName—Name of a BGP peer group to clear *—Clears all connections Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 411: Clear Bridge
VPLS instance created with the bridge vpls transport-virtual-router command Mode Privileged Exec Related Topics Clearing Dynamic MAC Addresses from the VPLS Forwarding Table in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 412: Clear Bridge Address
The MAC address format is a dotted triple of four-digit hexadecimal numbers; for example, 0090.1a40.4c7c Mode Privileged Exec Related Topics Clearing Dynamic MAC Addresses from the VPLS Forwarding Table in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 413: Clear Bridge Interface
Interface Types and Specifiers on page 5 Mode Privileged Exec Related Topics Clearing Dynamic MAC Addresses from the VPLS Forwarding Table in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 414: Clear Bridge Interface Vpls
VPLS instance created with the bridge vpls transport-virtual-router command Mode Privileged Exec Related Topics Clearing Dynamic MAC Addresses from the VPLS Forwarding Table in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 415: Clear Egress-Queue
Interface Types and Specifiers on page 5 explicit—Clears queues only on the specified interface and not queues stacked above the interface trafficClassName—Name of a traffic class for which egress queue statistics are cleared Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 416: Clear Fabric-Queue
Clears statistics for all fabric queues or for the specified traffic-class, egress-slot, or both. There is no no version. Options trafficClassName—Name of a traffic class for which fabric-queue statistics will be cleared egressSlot—Number of an egress slot for which fabric-queue statistics will be cleared Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 417: Clear Ip Bgp
Cisco-proprietary prefix list outbound route filters and triggers inbound soft reconfiguration Copyright © 2010, Juniper Networks, Inc.
Page 418 JunosE 11.2.x Command Reference Guide A to M out—Triggers outbound soft reconfiguration Mode Privileged Exec Related Topics Clearing BGP Attributes for L2VPNs Clearing BGP Attributes for VPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 419: Clear Ip Bgp Dampening
32–96 rtfAddress—rtfPrefix with a prefix length of 96; representing the route-target membership NLRI (RT-MEM-NLRI), in the format asNumber: extendedCommunity (for example, 320:320:524 or 320:50.2.3.4:524) vrfName—Name of a virtual routing and forwarding instance to clear Copyright © 2010, Juniper Networks, Inc.
Page 420 IP address Mode Privileged Exec Related Topics Clearing BGP Attributes for L2VPNs and Clearing BGP Attributes for VPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 421: Clear Ip Bgp Dynamic-Peers
BGP neighbor to clear ipv6Address—IPv6 address of identified BGP neighbor to clear peerGroupName—Name of a BGP peer group to clear *—Clears all connections vrfName—Name of a virtual routing and forwarding instance to clear Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 422: Clear Ip Bgp Redistribution
Reapplies policy to routes that have been redistributed into BGP. There is no no version. Options ipv4 unicast—Reapplies policy to redistributed IPv4 unicast routes ipv4 multicast—Reapplies policy to redistributed IPv4 multicast routes Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 423: Clear Ip Bgp Wait-End-Of-Rib
Mode Privileged Exec Related Topics Clearing BGP Attributes for L2VPNs and Clearing BGP Attributes for VPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 424: Clear Ip Demux
Release Information Command introduced before JunosE Release 7.1.0. Description Clears all dynamically created demultiplexer table entries associated with route-map processing of the set ip source-prefix command. There is no no version. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 425: Clear Ip Dhcp-Local Binding
NOTE: This command is deprecated and might be removed completely in a future release. The function provided by this command has been replaced by the dhcp delete-binding command. Options ipAddress—DHCP IP address binding to clear Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 426: Clear Ip Dvmrp Routes
Description Clears DVMRP routes from the routing table. There is no no version. Options ipAddress—IP address for which longest match is cleared addressMask—Address mask to be applied to the IP address Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 427: Clear Ip Flow Stats
Command introduced before JunosE Release 7.1.0. Description Clears all entries from all flow caches on the router. There is no no version. CAUTION: Using this command may temporarily disrupt flow data collection. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 428: Clear Ip Interface
VRF; string of 1–32 alphanumeric characters interfaceType—Interface type; see “Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 429: Clear Ip Isis Redistribution
Command introduced before JunosE Release 7.1.0. Description Clears all the routes that have previously been redistributed into IS-IS and redistributes them using the current policy configuration. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 430: Clear Ip Mobile Binding
@—Name of the user for the mobile node specification when the nai keyword is specified, in the format @ ipAddress—IP address of the home agent all—Clears all the bindings in the binding table Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 431: Clear Ip Mroute
*—Clears all IP multicast forwarding entries grpAddress—Address of the multicast group for which forwarding entries should be cleared sourceAddress—Address of the multicast source for which forwarding entries should be cleared Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 432: Clear Ip Nat Translation
IP address outsideGlobalIpAddress—Outside global IP address tcp—Specifies a TCP port translation udp—Specifies a UDP port translation icmp—Specifies an ICMP port translation gre—Specifies a GRE translation insideGlobalPort—Inside global port number insideLocalPort—Inside local port number Copyright © 2010, Juniper Networks, Inc.
Page 433 Chapter 4: C Commands outsideGlobalPort—Outside global port number outsideLocalPort—Outside local port number Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 434: Clear Ip Ospf Database
Syntax clear ip ospf database Release Information Command introduced in JunosE Release 7.1.0. Description Deletes all entries from the OSPF link-state database and resets all adjacencies. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 435: Clear Ip Ospf Neighbor
Issue the clear ip ospf database command to clear and reset the OSPF adjacencies. Issue the shutdown command followed by the no shutdown command on the interface. Options neighborAddress—IP address of identified neighbor to clear or reset Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 436: Clear Ip Ospf Redistribution
Clears and readvertises all of the routes that have been previously redistributed into OSPF. Exercise caution when using this command as it purges all external LSAs and reoriginates. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 437: Clear Ip Pim Auto-Rp
Command introduced before JunosE Release 7.1.0. Description Clears the group-to-RP router mappings the router learned via autoRP. There is no no version. Options ipAddress—IP address of the router designated as an RP router Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 438: Clear Ip Pim Interface Count
There is no no version. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 439: Clear Ip Pim Remote-Neighbor Count
NOTE: This command is typically used when you configure PIM remote neighbors to run multicast services over BGP/MPLS VPNs. That functionality is no longer supported. Options ipAddress—IP address of the interface Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 440: Clear Ip Prefix-List
192.168.32.0 or 10.10.0.0 length—Length of the network prefix; number of bits masking base address to produce address to be matched Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 441: Clear Ip Prefix-Tree
192.168.32.0 or 10.10.0.0 length—Length of the network prefix; number of bits masking base address to produce address to be matched Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 442: Clear Ip Rip Dynamic-Interfaces
Release Information Command introduced before JunosE Release 7.1.0. Description Clears all existing dynamic, unnumbered interfaces that were created since issuing the ip rip copy-to-dynamic command. There is no no version. Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 443: Clear Ip Rip Redistribution
Release Information Command introduced before JunosE Release 7.1.0. Description Clears all the routes that have previously been redistributed into RIP. There is no no version. Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 444: Clear Ip Routes
*—Clears all dynamic routes ipAddress—IP address prefix for routes that are cleared; in 32-bit dotted-decimal format ipMask—Mask of the IP address prefix for routes that are cleared; in 32-bit dotted-decimal format Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 445: Clear Ip Routes Download
VRFs. reload—Performs a route download operation, then clears all downloaded routes from the routing tables in all virtual routers and VRFs. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 446: Clear Ip Tunnel-Routes
*—Clears all dynamic routes ipAddress—IP address prefix for routes that are cleared; in 32-bit dotted-decimal format ipMask—Mask of the IP address prefix for routes that are cleared; in 32-bit dotted-decimal or /N format Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 447: Clear Ipv6 Access-List
Command introduced before JunosE Release 7.1.0. Description Clears counters for entries in IP access lists. There is no no version. Options accessListName—Name of the access list; a string of up to 32 characters Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 448: Clear Ipv6 Bfd Session
Description Restarts all IPv6 BFD sessions or a specified BFD session. There is no no version. Options ipAddress—IP address of the destination to which the session has been established Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 449: Clear Ipv6 Interface
There is no no version. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 450: Clear Ipv6 Mroute
*—Clears all IPv6 multicast forwarding entries grpAddress—Address of the multicast group for which forwarding entries should be cleared sourceAddress—Address of the multicast source for which forwarding entries should be cleared Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 451: Clear Ipv6 Neighbors
Clears all IPv6 dynamic neighbors. The include-statics keyword clears both dynamic neighbors and static neighbors. The statics-only keyword clears only IPv6 static neighbors. There is no no version. Options include-statics—Clears both dynamic and static neighbors statics-only—Clears only static neighbors Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 452: Clear Ipv6 Ospf Counters
Command introduced before JunosE Release 7.1.0. Description Clears all OSPF IPv6 statistical counters for the virtual router. There is no no version. Options processId—Number in the range 1–65535 that identifies the OSPF process Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 453: Clear Ipv6 Ospf Process
Command introduced before JunosE Release 7.1.0. Description Clears the OSPF IPv6 process on the virtual router. There is no no version. Options processId—Number in the range 1–65535 that identifies the OSPF process Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 454: Clear Ipv6 Ospf Redistribution
Clears and readvertise all of the routes that have been previously redistributed into OSPF. Exercise caution when using this command as it purges all external LSAs and reoriginates. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 455: Clear Ipv6 Pim Interface
IPv6 interface. There is no no version. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 456: Clear Ipv6 Pim Remote-Neighbor
Command introduced before JunosE Release 7.1.0. Description Clears the counters for remote neighbor statistics on all IPv6 interfaces or the specified IPv6 interface. There is no no version. Options ipv6Address—IPv6 address of the interface Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 457: Clear Ipv6 Prefix-List
::ffff:a:b:c:d length—Length of the network prefix; number of bits masking base address to produce address to be matched Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 458: Clear Ipv6 Routes
Clears IPv6 routes. To clear the routes for a specific IPv6 network, specify the IPv6 prefix. To clear all dynamic IPv6 routes, use the * (asterisk) option. There is no no version. Options ipv6Prefix—IPv6 network for which to clear route information *—Clears all dynamic IPv6 routes Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 459: Clear Ipv6 Tunnel-Routes
IPv6 network, specify the IPv6 prefix. To clear all dynamic IPv6 routes, use the * (asterisk) option. There is no no version. Options ipv6Prefix—IPv6 network for which to clear route information *—Clears all dynamic IPv6 routes Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 460: Clear Isis Adjacency
Clears all entries from the adjacency database, or clears only adjacencies with a specified neighbor. There is no no version. Options systemID—System ID of an IS-IS neighbor hostname—Hostname of an IS-IS neighbor Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 461: Clear Isis Database
Clears all entries from the IS-IS link-state database, or clears only entries associated with a specified neighbor. There is no no version. Options systemId—System ID of an IS-IS neighbor hostname—Hostname of an IS-IS neighbor Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 462: Clear Isis Ipv6 Redistribution
Command introduced in JunosE Release 8.2.0. Description Clears all the IPv6 routes that have previously been redistributed into IS-IS and redistributes them using the current policy configuration. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 463: Clear L2C Discovery-Table
Clears all entries or a specified entry from the topology discovery table. There is no no version. Options neighborName—Name of the neighbor you want to reset userId—User ID you want to reset Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 464: Clear L2C Neighbor
Release Information Command introduced before JunosE Release 7.1.0. Description Resets the specified GSMP neighbor session. There is no no version. Options neighborName—Name of the neighbor you want to reset Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 465: Clear Line
Mode User Exec Copyright © 2010, Juniper Networks, Inc.
Page 466: Clear Mirror Log
13 or above to use this command; an administrator can modify the user access level requirement. There is no no version. Mode Privileged Exec, User Exec Related Topics Monitoring Packet Mirroring Overview Logging Packet Mirroring Information Copyright © 2010, Juniper Networks, Inc.
Page 467: Clear Mpls Dynamic-Interfaces On-Major-Interfaces
IPv6 dynamic interfaces are removed and re-created interfaceType—Interface type; see “Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 468: Clear Mpls Ldp
0–32 mask—Mask for the prefix to be cleared neighborAddress—IP address of a neighbor 32-bit dotted-decimal format of the entry to be cleared Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 469: Clear Redundancy History
Chapter 4: C Commands clear redundancy history Syntax clear redundancy history Release Information Command introduced before JunosE Release 7.1.0. Description Clears the high availability switchover history for the router. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 470: Clear Rsvp Authentication
Clears the security association and resets the sequence number on the receiving peer for the specified sending peer. There is no no version. Options ip—Specifies keyword for compatibility with non–E Series implementations mpls—Indicates JunosE MPLS implementation ipAddress—IP address of sending peer Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 471: Clear Suspicious-Control-Flow-Detection
Interface Types and Specifiers on page 5 protocolValue—Name of the protocol to be cleared ethernetAddress—Ethernet address to be cleared slotNumber—Number of the slot to be cleared Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 472: Client-Name
The hostname command may be removed completely from Domain Map Tunnel Configuration mode in a future release. Options clientname—String of up to 64 characters (no spaces) Mode Domain Map Tunnel Configuration, Tunnel Group Tunnel Configuration Copyright © 2010, Juniper Networks, Inc.
Page 473: Clns Configuration-Time
Specifies the rate at which ES hellos and IS hellos are sent. The no version restores the default value, 10 seconds. Options configTime—Number in the range 1–65535; rate in seconds at which ES and IS hello packets are sent; default value is 10 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 474: Clns Holding-Time
The no version restores the default value, 30 seconds. Options holdTime—Number in the range 1–65535; length of time in seconds during which the information in the hello packets is considered valid Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 475: Clns Host
NSAP; first character can be either a letter or a number. If a number is used, the operations you can perform are limited. nsap—NSAP to which that name maps Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 476: Clock Set
Allows you to manually set the system clock. There is no no version. Options time—Current time (in 24-hour format – HH:MM:SS) month—Name of the month (January, February, …) day—Day of the month (1–31) year—Year (2000, 2001, …) Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 477: Clock Source
You must specify one of the following for internal clocking: module—Internal clock is from the line module itself chassis—Internal clock is from the configured system clock Mode Controller Configuration, Interface Configuration (POS only) Copyright © 2010, Juniper Networks, Inc.
Page 478: Clock Summer-Time Date
(24-hour format) in hours and minutes (hh:mm) stopDay—DST stop day stopMonth—DST stop month stopYear—DST stop year stopTime—DST stop time (24-hour format) dstOffset—Number of minutes to add during summer time in the range 1–1440; default = 60 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 479: Clock Summer-Time Recurring
(hh:mm) dstOffset—Number of minutes to add during summer time in the range 1–1440; default = 60 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 480: Clock Timezone
Standard time is in effect, such as EST or PST. hours—Hours offset from UTC (-23, -22 … 23) minutes—Minutes offset from UTC (0–59) Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 481: Color
Mode Classifier Group Configuration Related Topics Hierarchical Rate Limits Overview Policy Rule Precedence Copyright © 2010, Juniper Networks, Inc.
Page 482: Color-Aware
The no version restores the default value, which is not color-aware. Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 483: Color-Mark-Profile
Options profileName—Name of the rate-limit profile to be used in a policy (up to 40 alphanumeric characters) Mode Color Mark Profile Configuration, Global Configuration Related Topics Hierarchical Rate Limits Overview Policy Rule Precedence Copyright © 2010, Juniper Networks, Inc.
Page 484: Committed-Action
0–255 expValue—EXP bit value in the range 0–7 Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 485: Committed-Burst
100 ms; if 100ms is less than 8K, then 8K (8192). Options size—Size in bytes in the range 1–4294967295 milliseconds—Milliseconds in the range 1–10000 Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 486: Committed-Drop-Threshold
Command introduced before JunosE Release 7.1.0. Description Configures the threshold above which committed-drop-events are logged. The no version removes the threshold. Options committedDropThreshold—Bits per second in the range 0–1073741824 Mode Statistics Profile Configuration Related Topics Configuring Event Statistics Copyright © 2010, Juniper Networks, Inc.
Page 487: Committed-Length
Sets minimum and maximum constraints for the queue's committed lengths. The no version removes constraints on the queue's committed length. Options minimumCommittedLength—Range 0–1073741824 maximumCommittedLength—Range 0–1073741824 Mode Queue Profile Configuration Related Topics Configuring Queue Profiles to Manage Buffers and Thresholds Copyright © 2010, Juniper Networks, Inc.
Page 488: Committed-Rate
0–4294967295 parameterName—Name of policy parameter up to 40 characters percentValue—Percentage in the range 0–100 Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Setting the Committed Rate for a Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 489: Committed-Threshold
MinThresholdPercent—Minimum queue threshold as a percentage of queue length MaxThresholdPercent—Maximum queue threshold as a percentage of queue length MinThresholdBytes—Minimum queue threshold in bytes MaxThresholdBytes—Maximum queue threshold in bytes MaxDropProbability—Maximum drop probability Mode Drop Profile Configuration Related Topics Configuring RED Configuring WRED Copyright © 2010, Juniper Networks, Inc.
Page 490: Common-Name
Command introduced before JunosE Release 7.1.0. Description Specifies a common name used to generate certificate requests. The no version removes the common name. Options commonName—Name of up to 60 characters Mode IPSec Identity Configuration Copyright © 2010, Juniper Networks, Inc.
Page 491: Configure
‘.’ during script execution dotPeriod—Number of commands executed before a ‘.’ is displayed; default value is Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 492: Confirmations Explicit
Requires the user to enter y, ye, or yes to confirm a prompt, and to enter n or no to deny a prompt. The no version restores the default state, which permits pressing <Enter> or <y> to confirm a prompt and entering any other characters to deny a prompt. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 493: Conformed-Action
0–255 expValue—EXP bit value in the range 0–7 Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 494: Conformed-Drop-Threshold
JunosE Release 7.2.0. Description Configures the threshold above which conformed-drop-events are logged. The no version removes the threshold. Options conformedDropThreshold—Bits per second in the range 0–1073741824 Mode Statistics Profile Configuration Related Topics Configuring Event Statistics Copyright © 2010, Juniper Networks, Inc.
Page 495: Conformed-Fraction
The no version returns the conformed fraction to its default setting. Options conformedFraction—Percentage in the range 0–100; default value is 50 Mode Queue Profile Configuration Related Topics Configuring Queue Profiles to Manage Buffers and Thresholds Copyright © 2010, Juniper Networks, Inc.
Page 496: Conformed-Length
Sets minimum and maximum constraints for the queue's conformed lengths. The no version removes constraints on the queue's conformed length. Options minimumConformedLength—Number in the range 0–1073741824 maximumConformedLength—Number in the range 0–1073741824 Mode Queue Profile Configuration Related Topics Configuring Queue Profiles to Manage Buffers and Thresholds Copyright © 2010, Juniper Networks, Inc.
Page 497: Conformed-Threshold
MinThresholdPercent—Minimum queue threshold as a percentage of queue length MaxThresholdPercent—Maximum queue threshold as a percentage of queue length MinThresholdBytes—Minimum queue threshold in bytes MaxThresholdBytes—Maximum queue threshold in bytes MaxDropProbability—Maximum drop probability Mode Drop Profile Configuration Related Topics Configuring RED Configuring WRED Copyright © 2010, Juniper Networks, Inc.
Page 498: Control-Plane
JunosE 11.2.x Command Reference Guide A to M control-plane Syntax control-plane Release Information Command introduced in JunosE Release 8.0.0. Description Enters Control Plane Configuration mode. There is no no version. Mode Global Configuration Related Topics Rate-Limiting Traffic Flows Copyright © 2010, Juniper Networks, Inc.
Page 499: Controlled-Interface-Type
Mode QoS Parameter Definition Related Topics Configuring a Basic Parameter Definition for QoS Administrators Creating a QoS Parameter on an Interface Superset or Interface Set Copyright © 2010, Juniper Networks, Inc.
Page 500: Controller E3
Accesses Controller Configuration mode so that you can configure an E3 controller. There is no no version. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 501: Controller Sonet
Selects an interface on which you want to configure SONET or SDH. There is no no version. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 502: Controller T3
Accesses Controller Configuration mode so that you can configure a T3 controller. There is no no version. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 503: Convergence-Factor
The no version removes the specified convergence factor from all simple shared shapers on the router. Options convergenceFactor—Percentage value in the range 0–99; default value is 50 Mode QoS Shared Shaper Control Configuration Related Topics Configuring Simple Shared Shaper Algorithm Variables Copyright © 2010, Juniper Networks, Inc.
Page 504: Copy
FTP directory sourceFilename—Name of the the source file destinationPath—Path to the destination in the format: networkPath | /incoming/subdirectory | /outgoing/subdirectory networkPath—Path to the network host incoming—Specifies the incoming router's FTP directory Copyright © 2010, Juniper Networks, Inc.
Page 505 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 506: Copy Running-Configuration
NOTE: A Perl script is provided in the Tools folder of the compressed software image bundle, which you downloaded from the Juniper Networks website, that enables you to view the text configuration in a configuration file that contains both binary and text configuration.
Page 507: Copy Running-Configuration Startup-Configuration
This command is prevented during the high availability initialization state. If the command is issued during this state, the CLI notifies you of the state and requests that you try again later. There is no no version. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 508: Copy Startup-Configuration
There is no no version. Options destination—Destination filename (* .cnf) force—Creates a copy even if the destination file already exists Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 509: Cost
OSPF auto-cost reference bandwidth Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 510: Country
[ no ] country countryCode Release Information Command introduced before JunosE Release 7.1.0. Description Specifies a country name used to generate certificate requests. The no version removes the country name. Options countryCode—Two-character country name Mode IPSec Identity Configuration Copyright © 2010, Juniper Networks, Inc.
Page 511: Crc
16—Specifies CRC-16, which transmits streams of 8-bit characters and generates 16-bit check bits per frame 32—Specifies CRC-32, which transmits longer streams at faster rates and therefore provides better ongoing error detection none—Disables CRC checking Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 512: Crl
CRL. If no CRL is found, the peer can still authenticate; this is the default. required—Specifies that the router must find a valid CRL; the CRL must be current, and the peer certificate must not appear in the CRL Mode IPSec CA Identity Configuration Copyright © 2010, Juniper Networks, Inc.
Page 513: Crypto Key Dss
SSH server host key and stops the SSH daemon if it is running. Issuing this command terminates any active client sessions. The next time the router boots after this command is issued, the SSH server daemon is not started. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 514 JunosE 11.2.x Command Reference Guide A to M Copyright © 2010, Juniper Networks, Inc.
Page 515: Chapter 5 D Commands
CHAPTER 5 D Commands Copyright © 2010, Juniper Networks, Inc.
Page 516: Data-Character-Bits
7—Specifies 7 data bits per character; this setting supports only characters in the standard ASCII set 8—Specifies 8 data bits per character; default setting, supports the full set of 8-bit international characters Mode Line Configuration Copyright © 2010, Juniper Networks, Inc.
Page 517: Dead-Interval
Sets the time period that the OSPF router waits without seeing hello packets from a remote neighbor before declaring the neighbor to be down. The no version restores the default value. Options deadInterval—Number in the range 1–65535 seconds; default value is 40 seconds Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 518: Deadtime
The no version restores the default value, 0, turning off the deadtime mechanism. Options recovery—Number of minutes that a server is marked as unavailable, in the range 0–1440; default value is 0 Mode RADIUS Configuration Copyright © 2010, Juniper Networks, Inc.
Page 519: Debounce
Number in the range 1–5 seconds; default value is 1 second. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 520: Debounce-Interval
Number in the range 1–5 seconds; default value is 1 second. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 521: Debounce-Time
Sets the interval to wait before bringing up a RIP interface that was brought down. The no version restores the default value, 10. Options interval—Seconds in the range 0–60 Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 522: Debug Ip Bgp
0–7; the lower the number, the higher the priority: emergency or 0—System unusable alert or 1—Immediate action needed critical or 2—Critical condition exists Copyright © 2010, Juniper Networks, Inc.
Page 523 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 524: Debug Ip Mbgp
0–7; the lower the number, the higher the priority: emergency or 0—System unusable alert or 1—Immediate action needed critical or 2—Critical condition exists Copyright © 2010, Juniper Networks, Inc.
Page 525 Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 526: Debug Ip Ospf
0–7; the lower the number, the higher the priority: emergency or 0—System unusable alert or 1—Immediate action needed critical or 2—Critical condition exists error or 3—Error condition warning or 4—Warning condition notice or 5—Normal but significant condition Copyright © 2010, Juniper Networks, Inc.
Page 527 Chapter 5: D Commands info or 6—Informational message debug or 7—Debug message verbosityLevel—Verbosity of the log category's messages; can be any of the following: low—Terse medium—Moderate detail high—Verbose Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 528: Debug Ip Pim
0–7; the lower the number, the higher the priority: emergency or 0—System unusable alert or 1—Immediate action needed critical or 2—Critical condition exists error or 3—Error condition Copyright © 2010, Juniper Networks, Inc.
Page 529 (with the source and group keywords) number of source-group pairs for PIM sparse mode (with the rp keyword) number of source-group pairs associated with the RP router for PIM sparse mode Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 530: Debug Ip Rip
4—Warning condition notice or 5—Normal but significant condition info or 6—Informational message debug or 7—Debug message verbosityLevel—Verbosity of the log category's messages; can be any of the following: low—Terse medium—Moderate detail high—Verbose Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 531: Debug Ipv6 Ospf
0–7; the lower the number, the higher the priority: emergency or 0—System unusable alert or 1—Immediate action needed critical or 2—Critical condition exists error or 3—Error condition warning or 4—Warning condition notice or 5—Normal but significant condition Copyright © 2010, Juniper Networks, Inc.
Page 532 JunosE 11.2.x Command Reference Guide A to M info or 6—Informational message debug or 7—Debug message verbosityLevel—Verbosity of the log category's messages; can be any of the following: low—Terse medium—Moderate detail high—Verbose Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 533: Debug Ipv6 Pim
0—System unusable alert or 1—Immediate action needed critical or 2—Critical condition exists error or 3—Error condition warning or 4—Warning condition notice or 5—Normal but significant condition info or 6—Informational message debug or 7—Debug message Copyright © 2010, Juniper Networks, Inc.
Page 534 (with the source and group keywords) number of source-group pairs for PIM sparse mode (with the rp keyword) number of source-group pairs associated with the RP router for PIM sparse mode Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 535: Debug Isis
3—Error condition warning or 4—Warning condition notice or 5—Normal but significant condition info or 6—Informational message debug or 7—Debug message verbosityLevel—Verbosity of the log category's messages; can be any of the following: Copyright © 2010, Juniper Networks, Inc.
Page 536 JunosE 11.2.x Command Reference Guide A to M low—Terse medium—Moderate detail high—Verbose Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 537: Default-Fields Peer
BGP session times-up—Number of times the session has been established up-down-time—How long the session has been up or down updates-received—Number of update messages received from the peer Copyright © 2010, Juniper Networks, Inc.
Page 538 JunosE 11.2.x Command Reference Guide A to M updates-sent—Number of update messages sent to the peer *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 539: Default-Fields Route
IGP cost to the indirect next hop Copyright © 2010, Juniper Networks, Inc.
Page 540 *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 541: Default-Information Originate
1—Sets the default route's metric type to OSPF external type 1 metric-type 2—Sets the default route's metric type to OSPF external type 2 *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Copyright © 2010, Juniper Networks, Inc.
Page 542 JunosE 11.2.x Command Reference Guide A to M Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 543: Default-Metric
1–16 interfaceType—Interface type; see “Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 544: Default-Router
The no version removes the association between the address pool and the router. Options ipAddressPrimary—IP address of preferred router ipAddressSecondary—IP address of secondary router Mode DHCP Local Pool Configuration Copyright © 2010, Juniper Networks, Inc.
Page 545: Default-Upper-Type Mlppp
Description Specifies that L2TP creates an MLPPP interface for the current LNS session when full LCP proxy data is not available. The no version deletes the MLPPP specification. Mode L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 546: Delete
The force keyword is ignored when you attempt to delete any .dmp or .tsa file (unless the deletion is issued from a .mac or .scr file); this means that the CLI always prompts for confirmation for these file types. Mode Boot, Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 547: Delta-Sampling
ID of the discontinuity MIB attribute that you want to use for this trigger discontinuity-id-type—Specifies a discontinuity ID type (either timeStamp or timeTicks). The discontinuity ID type indicates the time value that you expect for a specific sample. Mode SNMP Trigger Configuration Copyright © 2010, Juniper Networks, Inc.
Page 548: Deny
Command introduced before JunosE Release 7.1.0. Description Specifies the domain name(s) that are to be denied access to AAA authentication. The no version negates the command. Options domainName—Name of the domain; maximum of 64 characters Mode AAA Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 549: Description
Options name—Text string or alias of up to 256 characters (in Interface Configuration mode) or up to 80 characters (in Controller Configuration mode and VRF Configuration mode) Mode Controller Configuration, Interface Configuration, VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 550: Dhcp Delete-Binding
Deletes the specified DHCP client bindings. There is no no version. NOTE: This command replaces the deprecated clear ip dhcp-local binding and dhcp-external delete-binding commands, which may be removed completely in a future release. Copyright © 2010, Juniper Networks, Inc.
Page 551 *, plus sign +, or question mark ? [ ] Matches any enclosed character; specifies a range of single characters – (hyphen) Used within brackets to specify a range of AS or community numbers Copyright © 2010, Juniper Networks, Inc.
Page 552 74 is represented by t, byte F3 is represented by \\xf3, 6f is represented by o, 6e is represented by n, and 65 is represented by e. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 553: Dhcp-External Delete-Binding
NOTE: This command is deprecated and might be removed completely in a future release. The function provided by this command has been replaced by the dhcp delete-binding command. Options bindingId—DHCP binding ID associated with the user. all—Specifies all bindings Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 554: Dhcp-External Duplicate-Mac-Address
MAC mode, which uses only the MAC address to uniquely identify DHCP clients. Mode Global Configuration Related Topics DHCP External Server Identification of Clients with Duplicate MAC Addresses Overview Configuring DHCP External Server to Uniquely Identify Clients with Duplicate MAC Addresses Copyright © 2010, Juniper Networks, Inc.
Page 555: Dhcpv6 Delete-Binding
(address and subnetwork mask) of the DHCPv6 clients; for example, 2002:2:4:1::/64 string—Local address pool name in the range 1–16 characters; for example, server4pool Mode Privileged Exec Related Topics Deleting DHCPv6 Client Bindings Monitoring DHCPv6 Local Server Binding Information Copyright © 2010, Juniper Networks, Inc.
Page 556: Diag
SRP modules; specify this keyword to restart only an individual fabric slice force—Specifies that the system manually confirm conflicting conditions when the slot of the active SRP module is specified Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 557: Diag-Level
The default diagnostics level is normal. There is no no version. Options normal—executes full diagnostics on the boot of the line card bypass—skips diagnostic tests on the boot of the line card Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 558: Dir
(*) in any position in a filename substitutes for zero or more characters; you cannot use a wildcard in a path short—Limits display to file name and creation date Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 559: Disable
5—Allows the user to execute Privileged Exec show commands plus the commands at levels 1 and 0 10—Allows the user to execute all commands except support commands, which may be provided by Juniper Networks Customer Service 15—Allows the user to execute support commands Mode...
Page 560: Disable-Autosync
SRP module. The no version restores the default situation, in which automatic synchronization runs as a background process every 5 minutes. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 561: Disable-Dynamic-Redistribute
Halts the dynamic redistribution of routes that are initiated by changes to a route map. Supported by DVMRP, BGP, IS-IS, OSPF, and RIP. The no version reenables dynamic redistribution of routes. Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 562: Disable-Incremental-External-Spf
Command introduced before JunosE Release 7.1.0. Description Disables incremental external SPF on the router; results in a full SPF when an event occurs to trigger an external SPF. The no version reenables incremental external SPF. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 563: Disable Proxy Lcp
Command introduced before JunosE Release 7.1.0. Description Disables the proxy LCP parameter for the remote host. The no version enables the proxy LCP parameter for the remote host. Mode L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 564: Disable-Switch-On-Error
Issue the sync command immediately before you issue this command. The no version restores the default situation, in which the redundant SRP module takes over if the primary SRP module experiences a failure. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 565: Disconnect-Cause
LAC to obtain information about the cause of a session disconnection. The no version disables generation of the PPP Disconnect Cause Code AVP, which is the default setting. Mode L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 566: Disconnect Ssh
VTY where the SSH session resides; use the show users command to determine the identifier sessionId—Integer in the range 0–4294967295 that identifies the session to be terminated Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 567: Discovery-Mode
If discovery mode is disabled, it does not accept topology discovery messages and stops advertising topology discovery capability. It does not affect any other neighbors. The no version disables ANCP discovery mode. Mode L2C Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 568: Distance
*—Indicates that one or more parameters can be repeated multiple times in a list in the command line ripWeight—Administrative distance assigned to RIP routes added to the IP routing table in the range 0–255; default value is 120 Mode Address Family Configuration (RIP), Router Configuration (OSPF or RIP) Copyright © 2010, Juniper Networks, Inc.
Page 569: Distance Bgp
AS in the range 1–255; default value is 200 localDistance—Administrative distance for local (redistributed) routes in the range 1–255; default value is 200 Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 570: Distance Ip
A distance of 255 prevents the route from being installed in the routing table. The no version restores the default value, 115. Options weight—Administrative distance assigned to IS-IS routes added to the IP routing table in the range 1–255 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 571: Distribute-Domain-Wide
Increases the granularity of routing information within an IS-IS domain by allowing routes to be distributed from level 2 to level 1. This results in more accurate routing between level 1 areas. The no version disables the command. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 572: Distribute-List
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Address Family Configuration, Remote Neighbor Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 573: Dns-Domain-Search
DHCPv6 client uses when it resolves hostnames with the DNS server. You can specify a maximum of four DNS domains for the search list of an IPv6 local pool; maximum of 32 characters Mode IPv6 Local Pool Configuration Copyright © 2010, Juniper Networks, Inc.
Page 574: Dns-Server
Assigns a DNS server to an address pool. The no version removes the association between the address pool and the DNS server. Options ipAddressPrimary—IP address of preferred DNS server ipAddressSecondary—IP address of secondary DNS server Mode DHCP Local Pool Configuration Copyright © 2010, Juniper Networks, Inc.
Page 575: Dns-Server (For Ipv6)
DNS Recursive Name Server option. The no version removes the configured DNS server addresses. Options ipv6AddressPrimary—IPv6 address of the primary DNS server. ipv6AddressSecondary—IPv6 address of the secondary DNS server. Mode IPv6 Local Pool Configuration Copyright © 2010, Juniper Networks, Inc.
Page 576 Allows you to issue an Exec mode command from any configuration command mode. This command functions the same as the run command. There is no no version. Options execCommand—CLI command that you can issue from User Exec or Privileged Exec mode Mode All configuration command modes Copyright © 2010, Juniper Networks, Inc.
Page 577: Domain
Specifies the domain to an automatically generated username in an IP service profile. The no version removes the domain. Options domainName —Name of the domain; maximum of 32 characters Mode IP Service Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 578: Domain-Authentication
IS-IS level 2 CSNPs and PSNPs is disabled. Options csnp—Enables authentication of IS-IS level 2 complete sequence number PDUs (CSNPs) psnp—Enables authentication of IS-IS level 2 partial sequence number PDUs (PSNPs) Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 579: Domain-Authentication-Key
Options 0—indicates the authKey is entered in unencrypted form (plaintext); this is the default option 8—indicates the authKey is entered in encrypted form (ciphertext) authKey—password; string of up to 8 characters Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 580: Domain-Id
ID in IP address format; default value is the IP address of the OSPF router configured in the VRF domainId—OSPF domain ID as an integer value in the range 0–4294967295; default value is 0 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 581: Domain-Message-Digest-Key
HH : MM[ : SS ]. startGenTime, startGenMonth, startGenDay, startGenYear—Time, month, day, year that the router will start inserting this password into packets. Use military time format HH : MM[ : SS ]. Copyright © 2010, Juniper Networks, Inc.
Page 582 HH : MM[ : SS ]. stopGenTime, stopGenMonth, stopGenDay, stopGenYear—Time, month, day, year that the router will stop inserting this password into packets. Use military time format HH : MM[ : SS ]. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 583: Domain-Name
The no version removes the domain name. Options domainName—Name of the domain domainName—Name used in certificate requests and in IKE authentication messages; up to 60 characters Mode DHCP Local Pool Configuration, IPSec Identity Configuration Copyright © 2010, Juniper Networks, Inc.
Page 584: Domain-Suffix
Appends a domain suffix to user-provided usernames on this profile. The no version restores the default value, no domain suffix, and usernames are passed transparently to AAA. Options domainSuffix—Domain suffix that you want to append to user-provided usernames. Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 585: Domain-Tag
Sets the VPN route tag for an OSPF VRF on a PE to prevent routing loops back into the VPN. The no version restores the default value. Options routeTag—Number identifying the VPN route tag in the range 0–4294967295 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 586: Dont-Install-Routes
IP routing table of the VR or VRF in which OSPF is running. The no version restores the default behavior, which installs the routes in the IP routing table. Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 587: Dos-Protection-Group
Creates a denial of service (DoS) protection group and enters DoS Protection Group Configuration mode. The no version removes the DoS protection group. Options groupName—Name of the DoS protection group; string of up to 31 alphanumeric characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 588: Drop-Profile
Release Information Command introduced before JunosE Release 7.1.0. Description Creates a drop profile. The no version removes the drop profile. Options dropProfileName—Name for the drop profile Mode Global Configuration Related Topics Configuring RED Configuring WRED Copyright © 2010, Juniper Networks, Inc.
Page 589: Ds3-Scramble
Command introduced before JunosE Release 7.1.0. Description Enables scrambling of the ATM cell payload on a T3 interface. DS3 scrambling assists clock recovery on the receiving end of the interface. The no version disables cell scrambling. Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 590: Dsr-Detect
If a session is in progress and the DSR signal is lost, the user is logged out automatically. The no version restores the default of no DSR required. Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 591: Dsu Bandwidth
DSU mode you specify. The actual speed of the fractional T3 lines will be the value closest to the fractional bandwidth you specify. Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 592: Dsu Mode
Options 0—Sets digital Link mode 2—Sets Larscom mode Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 593: Duplex
Fast Ethernet or Gigabit Ethernet interface half—Specifies that the router uses half duplex on a Fast Ethernet interface; this value is not valid for Gigabit Ethernet interfaces Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 594: Dvmrp Destination Profile
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 595: Chapter 6 E Commands
CHAPTER 6 E Commands Copyright © 2010, Juniper Networks, Inc.
Page 596: E3-Scramble
Command introduced before JunosE Release 7.1.0. Description Enables scrambling of the ATM cell payload on an E3 interface. E3 scrambling assists clock recovery on the receiving end of the interface. The no version disables scrambling. Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 597: Enable
1 and 0 10—Allows the user to execute all commands except support commands, which may be provided by Juniper Networks Customer Service, or the ability to assign privileges to commands 15—Allows the user to execute support commands and assign privileges to commands...
Page 598: Enabled
Command introduced in JunosE Release 8.1.0. Description Enables the aggregation cache to start accumulating information from the flow cache. The no version stops the information flow from the flow cache. Mode Flow Cache Configuration Copyright © 2010, Juniper Networks, Inc.
Page 599: Enable Ipsec-Transport
In L2TP Destination Profile Host Configuration mode, specifies that the router accepts only L2TP tunnels protected by an IPSec transport connection. The no version disables IPSec transport mode. Mode IP Tunnel Destination Profile Configuration, L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 600: Enable Password
1 and 0; this is the default level 10—Allows the user to execute all commands except support commands, which may be provided by Juniper Networks Customer Service 15—Allows the user to execute privilege setting and support commands passwordType: 0—Specifies that an unencrypted password follows;...
Page 601: Enable Proxy Authenticate
[ no ] enable proxy authenticate Release Information Command introduced before JunosE Release 7.1.0. Description Configures proxy authenticate for a remote host. The no version removes proxy authenticate configuration from the remote host. Mode L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 602: Enable Secret
1 and 0; this is the default level 10—Allows the user to execute all commands except support commands, which may be provided by Juniper Networks Customer Service 15—Allows the user to execute support commands secretType—One of the following: 0—Indicates that the secret is unencrypted;...
Page 603: Encapsulation
1483 encapsulation (LLC/SNAP or VC multiplexed) aal5mux ip—Configures a VC-based multiplexed circuit used for IP only aal5snap—Configures an LLC encapsulated circuit; an LLC/SNAP header precedes the protocol datagram Mode ATM VC Configuration, ATM VC Class Configuration Copyright © 2010, Juniper Networks, Inc.
Page 604: Encapsulation Bridge1483
MAC address for the interface. The MAC address format is a dotted triple of four-digit hexadecimal numbers; for example, 0090.1a40.4c7c. Multicast MAC address cannot be configured on bridged Ethernet interfaces. Mode Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 605: Encapsulation Frame-Relay Ietf
Description Enables Frame Relay encapsulation. The no version removes Frame Relay configuration from an interface. Mode Interface Configuration Related Topics Configuring Frame Relay Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 606: Encapsulation Hdlc
Syntax [ no ] encapsulation hdlc Release Information Command introduced before JunosE Release 7.1.0. Description Enables Cisco HDLC encapsulation. The no version disables Cisco HDLC on an interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 607: Encapsulation Mlframe-Relay Ietf
Release Information Command introduced before JunosE Release 7.1.0. Description Enables Multilink Frame Relay encapsulation. The no version removes Multilink Frame Relay configuration from an interface. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 608: Encapsulation Mlppp
Configures MLPPP as the encapsulation method on an individual interface. Creates an MLPPP link interface, which can be configured as a member of an MLPPP bundle. The no version disables MLPPP on an interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 609: Encapsulation Ppp
[ no ] encapsulation ppp Release Information Command introduced before JunosE Release 7.1.0. Description Configures PPP as the encapsulation method for the interface. The no version disables PPP on an interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 610: Encapsulation Pppoe
[ no ] encapsulation pppoe Release Information Command introduced before JunosE Release 7.1.0. Description Configures PPPoE as the encapsulation method for the interface. The no version removes PPPoE encapsulation from the interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 611: Encapsulation Vlan
Mode Interface Configuration, Subinterface Configuration Related Topics Configuring Ethernet/VLAN Layer 2 Services, Configuring Local Cross-Connects Between Ethernet/VLAN Interfaces, and Configuring S-VLAN Tunnels for Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 612: Encryption
Sets the encryption algorithm to use in the IKE policy. The no version restores the default, 3DES. Options des—Specifies 56-bit DES-CBC as the encryption algorithm 3des—Specifies 168-bit 3DES-CBC as the encryption algorithm Mode IKE Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 613: End
Release Information Command introduced before JunosE Release 7.1.0. Description Exits Global Configuration mode or any of the Configuration submodes and returns to the User Exec mode. There is no no version. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 614: Enrollment Retry-Limit
Specifies the number of minutes during which the router continues to send a certificate request to the CA. The no version restores the default. Options minutes—Number of minutes, from 0 (infinite time period) to 480; default value is 60 Mode IPSec CA Identity Configuration Copyright © 2010, Juniper Networks, Inc.
Page 615: Enrollment Retry-Period
Specifies the number of minutes that the router waits after receiving no response before resending a certificate request to the CA. The no version restores the default. Options minutes—Number of minutes in the range 0–60 minutes; default value is 1 Mode IPSec CA Identity Configuration Copyright © 2010, Juniper Networks, Inc.
Page 616: Enrollment Url
(using the ipsec ca enroll command). The no version deletes the URL specification. Options url—URL of SCEP server; in the format http://server_ipaddress; a maximum of 200 characters Mode IPSec CA Identity Configuration Copyright © 2010, Juniper Networks, Inc.
Page 617: Equipment Loopback
Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 618: Erase Secrets
The erase secrets command will not take any parameters and will not be available through a vty session until you enter no service unattended password-recovery. Options seconds—Number of seconds in the range 1–60 to allow for the operation Mode User Exec Copyright © 2010, Juniper Networks, Inc.
Page 619: Ethernet Description
Command introduced before JunosE Release 7.1.0. Description Adds a text description to a non-SRP Fast Ethernet or Gigabit Ethernet interface. The no version removes the description from the interface. Options name—String of up to 64 characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 620: Ethernet Dos-Protection-Group
Attaches an Ethernet denial of service (DoS) protection group to an interface. The no version removes the attachment of the DoS protection group from the interface. Options groupName—Name of the DoS protection group; string of up to 31 alphanumeric characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 621: Ethernet Oam Lfm
Mode Interface Configuration Related Topics ethernet oam lfm mode on page 585 Guidelines for Configuring 802.3ah OAM Link-Fault Management Configuring 802.3ah OAM Link-Fault Management Copyright © 2010, Juniper Networks, Inc.
Page 622: Ethernet Oam Lfm High-Threshold
Mode Interface Configuration Related Topics OAM Link Monitoring Feature Configuring 802.3ah OAM Link-Fault Management Example: Configuring 802.3ah OAM Link-Fault Management and Enabling Remote Failure Monitoring on an Interface Copyright © 2010, Juniper Networks, Inc.
Page 623: Ethernet Oam Lfm Link-Monitor Frame-Seconds
10–600 that represents a number of milliseconds in a multiple of 100; default value is 1000 milliseconds, which is denoted by specifying 10 units for the period variable in the CLI interface Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 624 Configuring 802.3ah OAM Link-Fault Management ethernet oam lfm link-monitor symbol-period on page 583 ethernet oam lfm link-monitor frame-seconds-summary on page 581 Example: Configuring 802.3ah OAM Link-Fault Management and Enabling Remote Failure Monitoring on an Interface Copyright © 2010, Juniper Networks, Inc.
Page 625: Ethernet Oam Lfm Link-Monitor Frame-Seconds-Summary
Integer in the range 10–900 seconds that is the monitoring period for framed symbol errors; default value is 60 seconds Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 626 Configuring 802.3ah OAM Link-Fault Management ethernet oam lfm link-monitor symbol-period on page 583 ethernet oam lfm link-monitor frame-seconds on page 579 Example: Configuring 802.3ah OAM Link-Fault Management and Enabling Remote Failure Monitoring on an Interface Copyright © 2010, Juniper Networks, Inc.
Page 627: Ethernet Oam Lfm Link-Monitor Symbol-Period
Integer in the range 1–60 seconds that is the monitoring period for symbol errors; there is no default value Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 628 Configuring 802.3ah OAM Link-Fault Management ethernet oam lfm link-monitor symbol-period on page 583 ethernet oam lfm link-monitor frame-seconds on page 579 Example: Configuring 802.3ah OAM Link-Fault Management and Enabling Remote Failure Monitoring on an Interface Copyright © 2010, Juniper Networks, Inc.
Page 629: Ethernet Oam Lfm Mode
OAM client can miss before a link-fault event is triggered; a number in the range 3–10; default value is 5 Mode Interface Configuration Related Topics OAM Discovery Feature Guidelines for Configuring 802.3ah OAM Link-Fault Management Configuring 802.3ah OAM Link-Fault Management Copyright © 2010, Juniper Networks, Inc.
Page 630: Ethernet Oam Lfm Pdu-Lost-Threshold
OAM client can miss before a link-fault event is triggered; a number in the range 3–10; default value is 5 Mode Interface Configuration Related Topics OAM Discovery Feature Configuring 802.3ah OAM Link-Fault Management ethernet oam lfm mode on page 585 Copyright © 2010, Juniper Networks, Inc.
Page 631: Ethernet Oam Lfm Pdu-Transmit-Interval
OAM client can miss before a link-fault event is triggered; a number in the range 3–10; default value is 5 Mode Interface Configuration Related Topics OAM Discovery Feature Configuring 802.3ah OAM Link-Fault Management ethernet oam lfm mode on page 585 Copyright © 2010, Juniper Networks, Inc.
Page 632: Ethernet Oam Lfm Remote-Failure
Mode Interface Configuration Related Topics OAM Remote Fault Detection Feature Configuring 802.3ah OAM Link-Fault Management Example: Configuring 802.3ah OAM Link-Fault Management and Enabling Remote Failure Monitoring on an Interface Copyright © 2010, Juniper Networks, Inc.
Page 633: Ethernet Oam Lfm Remote-Loopback
Interface Types and Specifiers on page 5 Mode Privileged Exec Related Topics OAM Remote and Local Loopback Feature ethernet oam lfm remote-loopback supported on page 590 Configuring 802.3ah OAM Link-Fault Management Example: Enabling Remote Loopback Support on the Local Interface Copyright © 2010, Juniper Networks, Inc.
Page 634: Ethernet Oam Lfm Remote-Loopback Supported
Mode Interface Configuration Related Topics OAM Remote and Local Loopback Feature ethernet oam lfm remote-loopback on page 589 Configuring 802.3ah OAM Link-Fault Management Example: Enabling Remote Loopback Support on the Local Interface Copyright © 2010, Juniper Networks, Inc.
Page 635: Event
The no version removes the event. Options eventOwner—Owner associated with this event; string of up to 32 alphanumeric characters eventName—Name associated with this event; string of up to 32 alphanumeric characters Mode SNMP Event Manager Configuration Copyright © 2010, Juniper Networks, Inc.
Page 636: Exceeded-Action
0–255; mark actions ar not supported on hierarchical rate limits expValue—EXP bit value in the range 0–7 Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 637: Exceeded-Drop-Threshold
Command introduced before JunosE Release 7.1.0. Description Configures the threshold above which exceeded-drop-events are logged. The no version removes the threshold. Options exceededDropThreshold—Bits per second in the range 0–1073741824 Mode Statistics Profile Configuration Related Topics Configuring Event Statistics Copyright © 2010, Juniper Networks, Inc.
Page 638: Exceeded-Fraction
The no version returns the exceeded fraction to its default setting. Options exceededFraction—Percentage range 0–100; default value is 25 Mode Queue Profile Configuration Related Topics Configuring Queue Profiles to Manage Buffers and Thresholds Copyright © 2010, Juniper Networks, Inc.
Page 639: Exceeded-Length
Sets minimum and maximum constraints for the queue's exceeded lengths. The no version removes constraints on the queue's exceeded length. Options minimumExceededLength—Range 0–1073741824 maximumExceededLength—Range 0–1073741824 Mode Queue Profile Configuration Related Topics Configuring Queue Profiles to Manage Buffers and Thresholds Copyright © 2010, Juniper Networks, Inc.
Page 640: Exceeded-Threshold
MinThresholdPercent—Minimum queue threshold as a percentage of queue length MaxThresholdPercent—Maximum queue threshold as a percentage of queue length MinThresholdBytes—Minimum queue threshold in bytes MaxThresholdBytes—Maximum queue threshold in bytes MaxDropProbability—Maximum drop probability Mode Drop Profile Configuration Related Topics Configuring RED Configuring WRED Copyright © 2010, Juniper Networks, Inc.
Page 641: Exception Dump
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 642: Exception Gateway
Specifies the gateway through which the router sends the core dump file to the remote FTP server. The no version returns the value to its default (null). Options ipAddress—IP address of the gateway Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 643: Exception Http-Redirect
This command is not supported for the ES2 10G Uplink LM. Mode Classifier Group Configuration Related Topics Assigning Values to the ATM CLP Bit Creating an Exception Rule within a Policy Classifier Group Copyright © 2010, Juniper Networks, Inc.
Page 644: Exception Monitor
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 645: Exception Monitor Interval
Specifies the interval at which you want the router to check NVS for core dump files. The no version disables the core dump monitor. Options interval—Number of minutes between NVS checks; in the range 1–1440 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 646: Exception Protocol Ftp
0—Indicates the password is unencrypted; the default 8—Indicates the password is encrypted userName—Username required to access the FTP server; the default username is anonymous password—Password required to access the FTP server; default value is no password Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 647: Exception Source
FTP server. The no version returns the value to its default (null). Options ipAddress—IP address of the interface ipAddressMask—Optionally add the IP address mask of the interface Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 648: Excess-Burst
The no version restores the default value, 0. Options size—Amount of bandwidth allocated; in the range 0–4294967295 milliseconds—Milliseconds in the range 1–10000 Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 649: Exclude-Prefix
IPv6 prefixes to be excluded from being delegated to the requesting router. If you specify this value, all prefixes from the starting IPv6 prefix up to this prefix are excluded from allocation. Mode IPv6 Local Pool Configuration Copyright © 2010, Juniper Networks, Inc.
Page 650: Exclude-Subsystem
Excludes subsystem files from being copied when you copy a software release to the router. The no version removes the exclusion for a specified subsystem file or all subsystem files. Options subsystemName—Name of the subsystem file to be excluded Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 651: Exec-Banner
(if any) and before the first prompt of a CLI session. The no version disables the exec banner and the motd banner on the line. The default version restores the default setting, in which the banner is enabled on all lines. Mode Line Configuration Copyright © 2010, Juniper Networks, Inc.
Page 652: Exec-Timeout
0 to 35791 seconds—Number of seconds in addition to the minutes for the time limit; in the range from 0 to 2147483 Mode Line Configuration Copyright © 2010, Juniper Networks, Inc.
Page 653: Existence-Test
Mode SNMP Trigger Configuration Copyright © 2010, Juniper Networks, Inc.
Page 654: Exit
Release Information Command introduced before JunosE Release 7.1.0. Description Exits the current command mode. In User Exec and Privileged Exec modes, logs out of the CLI. There is no no version. Mode All modes Copyright © 2010, Juniper Networks, Inc.
Page 655: Exit-Address-Family
Exits from Address Family Configuration mode and returns to Router Configuration mode. There is no no version. Mode Address Family Configuration Related Topics Configuring BGP Signaling for L2VPNs and Configuring BGP Signaling for VPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 656: Exit-Remote-Neighbor
JunosE 11.2.x Command Reference Guide A to M exit-remote-neighbor Syntax exit-remote-neighbor Release Information Command introduced before JunosE Release 7.1.0. Description Exits from Remote Neighbor Configuration mode and returns to Router Configuration mode. There is no no version. Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 657: Exp-Mask
Sets the EXP mask to be applied with the mark values. The no version restores the default mask of 7. Options maskValue—EXP mask value in the range 0–7 Mode Rate Limit Profile Configuration Related Topics Creating a Two-Rate Rate-Limit Profile Copyright © 2010, Juniper Networks, Inc.
Page 658: Export Destination
Configures an export destination for the aggregation cache. The no version removes the destination. Options hostName—Name of the destination host ipAddress—Address of IP interface udp-port—Specifies UDP port as the destination Mode Flow Cache Configuration Copyright © 2010, Juniper Networks, Inc.
Page 659: Export Map
32 alphanumeric characters filter—Prevents routes that do not match the route map from being exported; if absent, such routes are exported but their attributes are not modified by the route map Mode VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 660: Export Source
Command introduced in JunosE Release 8.1.0. Description Sets the source IP address for datagrams containing information from the cache. The no version removes the setting of the IP address. Options interface—Name of the interface Mode Flow Cache Configuration Copyright © 2010, Juniper Networks, Inc.
Page 661: Extended-Authentication
PAP protocol for extended authentication chap—Specifies the use of CHAP protocol for extended authentication re-authenticate—Enables reauthentication when IKE SA rekeying occurs skip-peer-config—Disables configuration of peer IP characteristics Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 662: External-Paths
Configures the maximum number of received external BGP best paths allowed for route-target signaling. The no version restores the default value, 1. Options limit—Number of paths, in the range 1–255 Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 663: F Commands
CHAPTER 7 F Commands Copyright © 2010, Juniper Networks, Inc.
Page 664: Fabric-Strict-Priority
Release Information Command introduced before JunosE Release 7.1.0. Description Specifies strict priority scheduling for queues in the traffic class in the fabric. The no version deletes the strict priority setting. Mode Traffic Class Configuration Copyright © 2010, Juniper Networks, Inc.
Page 665: Fabric-Weight
Specifies the relative weight for queues in the traffic class in the fabric. The no version sets the fabric weight to the default value. Options weight—Range 1–63; default value is 8 Mode Traffic Class Configuration Copyright © 2010, Juniper Networks, Inc.
Page 666: Fabric Weights
The no version returns the switch fabric to its default multicast:unicast ratio (15:2). Options multicastValue—Ratio value of multicast bandwidth in the range 1–15 unicastValue—Ratio value of unicast bandwidth in the range 1–15 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 667: Failover-Resync
L2TP host profiles and AAA domain map tunnels. L2TP uses the global failover method; the default setting Mode Domain Map Tunnel Configuration, L2TP Destination Profile Host Configuration Copyright © 2010, Juniper Networks, Inc.
Page 668: Filter
NOTE: This command replaces the Policy List Configuration version of the filter command, which may be removed completely in a future release. Mode Classifier Group Configuration Related Topics Policy Rule Precedence Copyright © 2010, Juniper Networks, Inc.
Page 669: Flash-Disk Compare
NVS; this option can take several minutes to complete configuration—Compares only configuration files; this option takes less time to complete because it compares only a subset of the files in the NVS file system Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 670: Flash-Disk Duplicate
Syntax flash-disk duplicate Release Information Command introduced before JunosE Release 7.1.0. Description Copies the contents of NVS on the primary SRP module to another NVS card. There is no no version. Mode Boot Copyright © 2010, Juniper Networks, Inc.
Page 671: Flash-Disk Initialize
Boot mode, because disk0 cannot be in an unmounted state in a router outside of Boot mode disk1—Specifies flash card in slot 1 of the SRP module; supported only on the E120 router and the E320 router Mode Boot, Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 672: Flash-Disk Scan
Boot mode, because disk0 cannot be in an unmounted state in a router outside of Boot mode disk1—Specifies flash card in slot 1 of the SRP module; supported only on the E120 router and the E320 router Mode Boot, Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 673: Forward
0–32768; default value is 100 Mode Policy List Configuration Related Topics Assigning Values to the ATM CLP Bit Copyright © 2010, Juniper Networks, Inc.
Page 674: Forward Interface
1–32767; default value is 100 Mode Classifier Group Configuration Related Topics Assigning Values to the ATM CLP Bit Copyright © 2010, Juniper Networks, Inc.
Page 675: Forward Next-Hop
1–32767; default value is 100 Mode Classifier Group Configuration Related Topics Assigning Values to the ATM CLP Bit Copyright © 2010, Juniper Networks, Inc.
Page 676: Forwarding-Rate-Threshold
Command introduced before JunosE Release 7.1.0. Description Configures the threshold above which forwarded-rate-exceeded events are logged. The no version removes the threshold. Options forwardingRateThreshold—Bits per second in the range 0–1073741824 Mode Statistics Profile Configuration Related Topics Configuring Event Statistics Copyright © 2010, Juniper Networks, Inc.
Page 677: Forwarding-Table Route-Holddown
0-30 seconds, where 0 specifies an update following each routing table change Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 678: Frame-Relay Class
Associates a map class with a subinterface. The no version removes the association between the map class and the subinterface. Options mapName—Name of the map class; use up to 64 characters Mode Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 679: Frame-Relay Classifier-List
0–15 deValue—Value of the DE bit to match; 0 or 1 Mode Global Configuration Related Topics Creating or Modifying Classifier Control Lists for Frame-Relay Policy Lists Copyright © 2010, Juniper Networks, Inc.
Page 680: Frame-Relay Description
The no version removes the description or alias. Options name—Text string or alias of up to 80 characters for the Frame Relay interface or subinterface Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 681: Frame-Relay Dos-Protection-Group
Attaches a Frame Relay denial of service (DoS) protection group to an interface. The no version removes the attachment of the DoS protection group from the interface. Options groupName—Name of the DoS protection group; string of up to 31 alphanumeric characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 682: Frame-Relay Fragment
The no version stops fragmentation and/or reassembly on the subinterface. Options fragmentSize—Maximum payload size of a fragment in bytes; a number in the range 16–8188; default value is 52 fragmentation-only—Specifies fragmentation only reassembly-only—Specifies reassembly only Mode Map Class Configuration Copyright © 2010, Juniper Networks, Inc.
Page 683: Frame-Relay Interface-Dlci Ietf
16–1007 Mode Subinterface Configuration Related Topics Configuring Frame Relay Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 684: Frame-Relay Intf-Type
Frame Relay network; the default nni—Router connects two Frame Relay networks Mode Interface Configuration Related Topics Configuring Frame Relay Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 685: Frame-Relay Keepalive
5–30; default value is 10 seconds; defines the keepalive interval; the interval must be set, and the value on the DTE should be less than the value set on the DCE Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 686: Frame-Relay Lmi-N391Dte
1– 255; default value is 6; number of keep exchanges to be done before requesting a full-status message. If you specify a value of 1, you receive full-status messages only. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 687: Frame-Relay Lmi-N392Dce
Options threshold—Positive number in the range 1– 10; number of errors that will place the interface in an operationally down state; default value is 2 errors Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 688: Frame-Relay Lmi-N392Dte
Options threshold—Positive number in the range 1–10; number of errors that will place the interface in an operationally down state; default value is 3 errors Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 689: Frame-Relay Lmi-N393Dce
1–10 events; specifies the diagnostic window used to verify link integrity; default value is 2 events (The detection of N392 errors within the window of N393 samples places the interface in an operationally down state.) Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 690: Frame-Relay Lmi-N393Dte
1–10 events; default value is 4 events; specifies the diagnostic window used to verify link integrity (the detection of N392 errors within the window of N393 samples places the interface in an operationally down state) Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 691: Frame-Relay Lmi-T391Dte
Options seconds—Number in the range 5–30 seconds; specifies the interval in seconds between status inquiries issued by the DTE; default value is 10 seconds Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 692: Frame-Relay Lmi-T392Dce
Options seconds—Number in the range 5–30 seconds; specifies the expected interval in seconds between status inquiries issued by the DTE equipment; default value is 15 seconds Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 693: Frame-Relay Lmi-Type
Group of Four specification developed by DEC, Northern Telecom, Stratacom, and Cisco q933a—ITU-T Q.933 Annex A none—No management interface is used Mode Interface Configuration Related Topics Configuring Frame Relay Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 694: Frame-Relay Policy
Mode Interface Configuration Related Topics Setting a Statistics Baseline for Policies Copyright © 2010, Juniper Networks, Inc.
Page 695: Frame-Relay Policy-List
Attaching this policy list to an interface filters all packets on that interface. The no version removes a policy list. Options policyName—Name of the policy list Mode Global Configuration Related Topics Creating Policy Lists for Frame Relay Copyright © 2010, Juniper Networks, Inc.
Page 696: Framing
The no version restores the default for that interface. Options framingType—One of the following framing types: E3 Frame g751—Default; G.751 compliant frame g832—G.832 compliant frame c-bit—Default; specifies c-bit parity framing m23—Specifies M23 multiplexer framing Mode Controller Configuration Copyright © 2010, Juniper Networks, Inc.
Page 697: Frequency
RTR operations, for both types (echo and pathEcho), the default value is 60 seconds; with MIB sampling, the default value is 600 seconds. Mode RTR Configuration, SNMP Event Manager Configuration Copyright © 2010, Juniper Networks, Inc.
Page 698: Ftp-Server Enable
Description Enables the FTP server and monitors the FTP port for attempts to connect to the FTP server. The no version terminates the current FTP sessions and disables the FTP server. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 699: Ftp-Server Flush
Forcibly terminates existing file transfer sessions to enable unified ISSU to proceed successfully. There is no no version. Mode Privileged Exec Related Topics FTP Server File Transfers Behaviors in the JunosE System Basics Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 700: Full-Spf-Always
[ no ] full-spf-always Release Information Command introduced before JunosE Release 7.1.0. Description Enables full SPF calculations for ISIS network changes. The no version restores partial route calculation (PRC) mode for SPF calculations. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 701: G Commands
CHAPTER 8 G Commands Copyright © 2010, Juniper Networks, Inc.
Page 702: Global Export Map
IPv4 routes are exported to the global BGP non-VPN RIB ipv6—Specifies that only IPv6 routes are exported to the global BGP non-VPN RIB routeMap—Name of a route map; string of up to 32 alphanumeric characters Mode VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 703: Global Import Map
IPv6 routes are imported from the global BGP non-VPN RIB routeMap—Name of a route map; string of up to 32 alphanumeric characters maxNumber—Maximum number of routes that can be imported; integer in the range 1–4294967295 Mode VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 704: Graceful-Restart
Configures hitless restart capability for OSPFv2. If high availability is active, the OSPF instance can perform a hitless restart when switching or failing over to the secondary SRP module. The no version disables OSPF graceful restart capability on the router. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 705: Graceful-Restart Helper
Command introduced before JunosE Release 7.1.0. Description Configures the router to function as an OSPFv2 or OSPFv3 graceful restart helper router. The no version disables OSPF graceful restart helper mode capability on the router. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 706: Graceful-Restart Helper-Abort-Topology-Change
The no version turns off the graceful restart helper capability. Options any—Abandons the helper role when any LSA changes during the restart non-externals—Abandons the helper role only when any nonexternal LSA changes during the restart Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 707: Graceful-Restart Notify-Time
The no version returns the notify duration timer to its default value, 15 seconds. Options notifyTime—Number of seconds during which the router can send purged grace LSAs over all interfaces; in the range 1–1800 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 708: Graceful-Restart Restart-Time
180 seconds. Options restartTime—Number of seconds during which the restarting router can reacquire OSPF neighbors that were fully functional prior to the restart; in the range 1–1800 Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 709: Grace-Period
0–23 minutes—Number of minutes in the grace period; in the range 0–59 seconds—Number of seconds in the grace period; in the range 0–59 Mode DHCP Local Pool Configuration Copyright © 2010, Juniper Networks, Inc.
Page 710: Gre Destination Profile
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 711: Green-Mark
The no version deletes the ToS mark value. Options colorMarkValue—Value of the ToS mark to be applied: in the range 0–255 Mode Color Mark Profile Configuration Related Topics Hierarchical Rate Limits Overview Policy Rule Precedence Copyright © 2010, Juniper Networks, Inc.
Page 712: Gre-Tunnel Classifier-List
ToS byte; in the range 0–255 classifierNumber—Index of the classifier control list entry to be deleted; an integer in the range 1–10000 Mode Global Configuration Related Topics Creating or Modifying Classifier Control Lists for GRE Tunnel Policy Lists Copyright © 2010, Juniper Networks, Inc.
Page 713: Gre-Tunnel Policy
Mode Interface Configuration Related Topics Setting a Statistics Baseline for Policies Copyright © 2010, Juniper Networks, Inc.
Page 714: Gre-Tunnel Policy-List
The no version deletes the policy list. Options policyName—Name of a policy list; string of up to 40 alphanumeric characters Mode Global Configuration Related Topics Creating Policy Lists for GRE Tunnels Copyright © 2010, Juniper Networks, Inc.
Page 715: Group
5—Specifies the 1536-bit group Mode IKE Policy Configuration, QoS Profile Configuration Related Topics Configuring a QoS Profile Configuring Shadow Nodes Configuring QoS for an L2TP Session Configuring QoS for Tunnel-Server Ports for L2TP LNS Sessions Copyright © 2010, Juniper Networks, Inc.
Page 716: Gsmp-Syn-Timeout
The no version reverts the session timeout to its default setting (60 seconds). Options timeOutValue— Session timeout in seconds. The timer value cannot be more than the ANCP session timeout value. The default value for the ANCP session timeout is 75 seconds. Mode L2C Configuration Copyright © 2010, Juniper Networks, Inc.
Page 717: H Commands
CHAPTER 9 H Commands Copyright © 2010, Juniper Networks, Inc.
Page 718: Halt
SRP module only standby-srp—Stops operation on standby SRP module only Mode Boot, Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 719: Hash
Sets the hash algorithm in an IKE policy. The no version restores the default, SHA-1. Options sha—Specifies SHA-1 (HMAC variant) as the hash algorithm md5—Specifies MD5 (HMAC variant) as the hash algorithm Mode IKE Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 720: Hdlc Dos-Protection-Group
Attaches an HDLC denial of service (DoS) protection group to an interface. The no version removes the attachment of the DoS protection group from the interface. Options groupName—Name of the DoS protection group; string of up to 31 alphanumeric characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 721: Hdlc Down-When-Looped
Release Information Command introduced before JunosE Release 7.1.0. Description Enables loopback detection on a Cisco HDLC interface. Loopback detection is disabled by default. The no version disables loopback detection. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 722: Hdlc Keepalive
The no version turns off the keepalive feature. Options seconds—Keepalive timeout period in the range 0–6553 seconds; default value is 10. A value of zero (0) turns off the keepalive feature. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 723: Hdlc Shutdown
[ no ] hdlc shutdown Release Information Command introduced before JunosE Release 7.1.0. Description Stops or restarts a Cisco HDLC session. The no version restarts a Cisco HDLC session. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 724: Hello Hold-Time
If all link hello adjacencies are deleted for an LDP session, then the LSR terminates the LDP session. The no version restores the default value, 15 seconds. Options seconds—Number of seconds, in the range 1–65535 Mode LDP Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 725: Hello Interval
Command introduced in JunosE Release 8.1.0. Description Specifies the interval between link-hello packets sent by LDP. The no version restores the default interval, 5 seconds. Options seconds—Number of seconds, in the range 1–65535 Mode LDP Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 726: Hello-Interval
Specifies the interval between hello packets that the router sends on the OSPF remote-neighbor interface. The no version restores the default value. Options helloInterval—Number in the range 1–65535 seconds; default value is 10 seconds Mode Remote Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 727: Help
Chapter 9: H Commands help Syntax help Release Information Command introduced before JunosE Release 7.1.0. Description Displays basic information about the Help system. There is no no version. Mode All modes Copyright © 2010, Juniper Networks, Inc.
Page 728: Hops-Of-Statistics-Kept
16 for a pathEcho entry and 1 for an echo entry; if you omit this option, all hops found are recorded NOTE: The E Series router supports only the pathEcho and echo types. Mode RTR Configuration Copyright © 2010, Juniper Networks, Inc.
Page 729: Host
8—Indicates that the password is an encrypted password password—Password used to access an FTP server (but not an NFS server); defaults to null tftp—Specifies that the host is a TFTP server Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 730: Hostname
NOTE: In Domain Map Tunnel Configuration mode, this command has been replaced by the clear suspicious-control-flow-detection command and may be removed completely from Domain Map Tunnel Configuration mode in a future release. Options hostname—String of up to 63 characters (no spaces) Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 731: Hotfix Activate
Options hfixFileName—Name of a hotfix software file (.hfx) on the local file system all—Specifies that all currently active hotfixes are deactivated Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 732 JunosE 11.2.x Command Reference Guide A to M Copyright © 2010, Juniper Networks, Inc.
Page 733: I Commands
CHAPTER 10 I Commands Copyright © 2010, Juniper Networks, Inc.
Page 734 Description Specifies the ANCP neighbor ID in the L2C Neighbor (config-l2c-neighbor) Configuration mode. The no version removes the neighbor ID. Options neighborId—ANCP neighbor ID (MAC address) in the form XXXX.XXXX.XXXX Mode L2C Neighbor Configuration Copyright © 2010, Juniper Networks, Inc.
Page 735: Identification
From Domain Map Tunnel Configuration or Tunnel Group Tunnel mode, specifies the assignment ID of an L2TP tunnel. The no version removes the assignment ID from the tunnel. Options serverId—L2TP tunnel assignment ID up to 32 characters Mode Domain Map Tunnel Configuration, Tunnel Group Tunnel Copyright © 2010, Juniper Networks, Inc.
Page 736: Idle-Character
Configures the HDLC idle character that is transmitted between HDLC packets. The no version restores the default value. Options flags—Sets the idle character to 0x7E; the default value marks—Sets the idle character to 0xFF Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 737: Igmp Disable
Syntax [ no ] igmp disable Release Information Command introduced before JunosE Release 7.1.0. Description Disables IGMP on a virtual router. The no version reenables IGMP on a virtual router. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 738: Igmp Promiscuous
Allows all IGMP interfaces on the router to accept IGMP reports from hosts on any subnet. The no version allows IGMP interfaces on the router to accept IGMP reports only from hosts on their associated subnets. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 739: Ignore-Lsp-Errors
Command introduced before JunosE Release 7.1.0. Description Allows the router to ignore IS-IS link-state packets that are received with internal checksum errors rather than purging the link-state packets. The no version disables this function. Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 740: Ike Crl
CRL, it uses it; this is the default required—Requires a valid CRL; either the certificates belonging to the E Series router or the peer must not appear in the CRL; this is the strictest setting Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 741: Ike Local-Identity
32-bit dotted decimal format (for example, 192.56.32.2) userName—Username used as the IKE local identity for IKE SA negotiations domainName—Domain name used as the IKE local identity for IKE SA negotiations (string of 1–32 characters) Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 742: Ike Peer-Identity Distinguished-Name
IKE identity type and the user-provided IKE identity matches each distinguished name field in this profile. The no version removes the peer IKE identity. Options dnString—String of 1–32 characters used as the distinguished name Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 743: Ike Peer-Identity Domain-Name
IKE identity type and the domain name portion of the IKE identity matches the domain name setting for this profile. The no version removes the peer IKE identity. Options domainName—String of 1–32 characters used as the domain name Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 744: Ike Peer-Identity Ip Address
IP address resides within the specified network. The no version removes the peer IKE identity. Options ipAddress—IP address in 32-bit dotted decimal format (for example, 192.56.32.2) ipMask—Mask for associated IP subnet in dotted decimal or prefix length notation Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 745: Ike Peer-Identity Username
IKE identity matches the username setting for this profile. The no version removes the peer IKE identity. Options userName—String of 1–32 characters used as the user name Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 746: Import Map
IPv4 routes are imported from the global BGP VPN RIB ipv6—Specifies that only IPv6 routes are imported from the global BGP VPN RIB routeMap—Name of a route map; string of up to 32 alphanumeric characters Mode VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 747: Inarp
ATM data PVC. The no version restores the default behavior, which disables InARP, in the VC class. Options frequency—InARP refresh rate in minutes, in the range 1–60; default value is 15 Mode ATM VC Configuration, ATM VC Class Configuration Copyright © 2010, Juniper Networks, Inc.
Page 748: Include Circuit-Identifier
IP service profile. The no version disables inclusion of the circuit identifier. Options circuitType—Type of circuit; atm or vlan prepend-circuit-type—Specifies that the circuit type is included in the username Mode IP Service Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 749: Include Dhcp-Option 82
DHCP relay agent information option (option 82) is included when the router automatically generates a username for an IP service profile. The no version disables inclusion of the suboption. Mode IP Service Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 750: Include Hostname
Command introduced in JunosE Release 7.3.0. Description Specifies that the router's hostname is included when the router automatically generates a username for an IP service profile. The no version disables inclusion of the hostname. Mode IP Service Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 751: Include Ip-Address
Description Specifies that the IP address is included when the router automatically generates a username for an IP service profile. The no version disables inclusion of the IP address. Mode IP Service Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 752: Include Mac-Address
Description Specifies that the MAC address is included when the router automatically generates a username for an IP service profile. The no version disables inclusion of the MAC address. Mode IP Service Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 753: Include Virtual-Router-Name
Specifies that the virtual router name is included when the router automatically generates a username for an IP service profile. The no version disables inclusion of the virtual router name. Mode IP Service Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 754: Index
(adjacent) to the previous node in the path. If loose is not configured, the configuration defaults to strict. Strict indicates that the node is directly connected to the previous node. Mode Explicit Path Configuration Copyright © 2010, Juniper Networks, Inc.
Page 755: Instance-Interface-Type
Mode QoS Parameter Definition Related Topics Configuring a Basic Parameter Definition for QoS Administrators Creating a QoS Parameter on an Interface Superset or Interface Set Copyright © 2010, Juniper Networks, Inc.
Page 756: Interface
Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 extension—Option that depends on the type of interface Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 757: Interface Atm
Global Configuration, Interface Configuration Related Topics Configuring an MPLS Pseudowire with VCC Cell Relay Encapsulation, Configuring Local ATM Cross-Connects with AAL5 Encapsulation, and Configuring MPLS LSPs for L2VPNs in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 758: Interface-Event-Disable
Specifies that RIP does not purge the routing table on a RIP interface that has been brought down. The no version restores the default condition, wherein RIP does purge the routing table on an interface after a down event. Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 759: Interface Fastethernet
Configuring Customer-Facing Interfaces in the L2VPN Instance, Configuring Ethernet/VLAN Layer 2 Services, Configuring Local Cross-Connects Between Ethernet/VLAN Interfaces, and Configuring S-VLAN Tunnels for Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 760: Interface Gigabitethernet
Global Configuration Related Topics Configuring the QoS Shaping Mode for Ethernet Interfaces Creating a QoS Interface Hierarchy for Bulk-Configured VLAN Subinterfaces with RADIUS Configuring a Parameter Definition to Shape Ethernet Traffic Using Cell Mode Copyright © 2010, Juniper Networks, Inc.
Page 761: Interface Ip
[ no ] interface ip interfaceName Release Information Command introduced before JunosE Release 7.1.0. Description Defines a shared IP interface. The no version removes the IP interface. Options interfaceName—String of up to 15 characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 762: Interface Ipv6
[ no ] interface ipv6 interfaceName Release Information Command introduced before JunosE Release 7.1.0. Description Defines a shared IPv6 interface. The no version removes the IPv6 interface. Options interfaceName—String of up to 15 characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 763: Interface Lag
Configuring the Scheduler Hierarchy for Hashed Load Balancing in 802.3ad Link Aggregation Groups Configuring the Scheduler Hierarchy for Subscriber Load Balancing in 802.3ad Link Aggregation Groups Configuring Load Rebalancing for 802.3ad Link Aggregation Groups Copyright © 2010, Juniper Networks, Inc.
Page 764: Interface Loopback
ATM Cross-Connects with AAL5 Encapsulation, Configuring Local Cross-Connects Between Ethernet/VLAN Interfaces, Configuring the Loopback Interface and Router ID for BGP for L2VPNs, and Configuring the Loopback Interface and Router ID for VPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 765: Interface Mlframe-Relay
Defines an MLFR bundle or a subinterface in a bundle. The no version removes the bundle or subinterface. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 766: Interface Mlppp
Creates an MLPPP network interface, also known as the MLPPP bundle. The no version deletes the MLPPP bundle. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 767: Interface Null
Selects the null interface, which does not forward traffic. The null interface acts as a data sink. Though you can access the null interface, you cannot configure any values for it or delete it. There is no no version. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 768: Interface Pos
Interface Types and Specifiers on page 5 Mode Global Configuration Related Topics Configuring HDLC Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 769: Interface Serial
Interface Types and Specifiers on page 5 Mode Global Configuration Related Topics Configuring Frame Relay Layer 2 Services and Configuring HDLC Layer 2 Services in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 770: Interface Tengigabitethernet
Specifies or creates a 10-Gigabit Ethernet interface or a subinterface over a 10-Gigabit Ethernet interface. The no version removes the interface or subinterface. Options interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 771: Interface Tunnel
(other than the current VR) in which the tunnel will be established ipsec-transport—Indicates that the tunnel is protected with IPSec in transport mode; used for GRE or DVMRP tunnels only Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 772: Invert Data
Command introduced before JunosE Release 7.1.0. Description Enables data stream inversion. Data stream inversion must be turned on by network personnel at the other end of the line. The no version disables data stream inversion. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 773 VPLS instance forwards IP packets deny—Specifies that the subscriber interface associated with the bridge group or VPLS instance filters IP packets Mode Subscriber Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 774: Ip Access-Routes
Enables the ability to create host access routes on a PPP interface, which is useful for the B-RAS application. It also enables an access route in a profile. The no version disables the feature. Mode Interface Configuration, Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 775: Ip Access-Route Table-Map
Filters access routes before an access list adds them to the routing table. The no version deletes the table map. Options mapName—Name of the table map that you want the router to use Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 776: Ip Address
Cross-Connects Between Ethernet/VLAN Interfaces, Configuring the Loopback Interface and Router ID for BGP for L2VPNs, Configuring the Loopback Interface and Router ID for VPLS, and Configuring MPLS LSPs for L2VPNs in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 777: Ip-Address
Specifies the IP address parameter for a user entry in the local user database. The no version deletes the IP address parameter from the user entry. Options ipAddress—IP address in 32-bit dotted decimal format (for example, 192.56.32.2) Mode Local User Configuration Copyright © 2010, Juniper Networks, Inc.
Page 778: Ip Address-Pool
Options dhcp—Enables the use of a DHCP server for address allocations local—Enables the use of local address pool for address allocations none—Does not enable an IP address pool Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 779: Ip-Address-Pool
IP address to the subscriber. The no version deletes the IP address pool parameter from the user entry in the local user database. Options poolName—Name of IP address pool Mode Local User Configuration Copyright © 2010, Juniper Networks, Inc.
Page 780: Ip Address Virtual-Router
32-bit dotted decimal format (for example, 192.56.32.2) to which you want to limit this policy rule vrName—Name of virtual router to which you want to limit this policy rule Mode IKE Policy Configuration Copyright © 2010, Juniper Networks, Inc.
Page 781: Ip Alwaysup
The no version makes the interface appear in its current state. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 782: Ip Analyzer
The no version removes the analyzer interface configuration from the interface. Options default—Specifies that this interface is the default analyzer interface for the virtual router Mode Interface Configuration Related Topics Configuring CLI-Based Mirroring Configuring RADIUS-Based Mirroring Copyright © 2010, Juniper Networks, Inc.
Page 783: Ip As-Path Access-List
* matches zero or more occurrences of any element + matches one or more occurrences of any element [ ] matches any elements enclosed between brackets ([ ]) - hyphen; used within brackets to specify a range of AS numbers Copyright © 2010, Juniper Networks, Inc.
Page 784 _ underscore; used in implementations on routers from other vendors on either side of a path to specify a literal and disallow substring matching. Allowed but not required in our CLI. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 785: Ip Atm-Vc
1–2147483647; virtual circuit descriptor; an identifier for the VC in other commands broadcast—Specifies that the circuit should participate in broadcast operations Mode Map List Configuration Copyright © 2010, Juniper Networks, Inc.
Page 786: Ip Auto-Configure Ip-Subscriber
Mode Interface Configuration, Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 787: Ip Auto-Detect Ip-Subscriber
When an unmatched packet is detected, an event is generated that determines whether to create a dynamic subscriber interface or to configure an existing interface. The no version disables autodetection. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 788: Ip Bgp-Community New-Format
Specifies that communities must be displayed in AA:NN format, where AA is a number that identifies the autonomous system and NN is a number that identifies the community within the autonomous system. The no version restores the default display. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 789: Ip Bgp-Confed-As-Set New-Format
Specifies that AS-confed-sets must be displayed within square brackets, [ ], with the ASs delimited by commas. The no version restores the default, displaying AS-confed-sets within parentheses, ( ), with the ASs delimited by spaces. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 790: Ip Block-Multicast-Sources
(for example, global). In Profile Configuration mode, blocks multicast sources per user on dynamic IP interfaces. The no version restores the default behavior of creating mroutes upon receiving multicast packets. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 791: Ip Broadcast-Address
Release Information Command introduced before JunosE Release 7.1.0. Description Defines a broadcast address for an interface. The no version restores the default IP broadcast address. Options ipAddress—Broadcast IP address Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 792: Ip Classifier-List
(IGMP, IP, TCP, or UDP) or number (in the range 0–255) to match sourceAddress—Source address to match sourceMask—Wild-card mask to apply to the source address host—Matches source or destination address as a host sourceHostAddress—Source host address to match any—Matches any source or destination address Copyright © 2010, Juniper Networks, Inc.
Page 793 NOT and & means logical AND; use any of the following flag names: ack—0x10 fin—0x01 push—0x08 rst—0x04 syn—0x02 urgent—0x20 ipFlags—Logic equation that specifies flag bit values; ! means logical NOT and & means logical AND; use any of the following flag names: dont-fragment—0x02 more-fragments—0x01 reserved—0x04 Copyright © 2010, Juniper Networks, Inc.
Page 794 ToS byte; in the range 0–255 classifierNumber—Index of the classifier control list entry to be deleted Mode Global Configuration Related Topics Creating or Modifying Classifier Control Lists for IP Policy Lists Copyright © 2010, Juniper Networks, Inc.
Page 795: Ip Community-List
BGP does not advertise this route to external peers; sometimes known as the no-export-subconfed community internet—Specifies the Internet community *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 796: Ip Debounce-Time
Defines the minimum time an IP interface must be in a given state—for example, up or down—before being reported. The no version removes the debounce time. Options vrfName—Name of the VRF; string of 1–32 alphanumeric characters period—Interval in the range 0–60000 milliseconds Mode Global Configuration, Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 797: Ip Demux-Type Da-Prefix
Command introduced before JunosE Release 7.1.0. Description Specifies that a subscriber interface will demultiplex traffic using destination addresses. The no version restores the default situation, in which the subscriber interface demultiplexes traffic using source addresses. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 798: Ip Description
IP interface. The description command may be removed completely from Interface Configuration mode in a future release. Options name—Name for the static IP interface; string of up to 256 characters Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 799: Ip Destination-Prefix
The no version removes the association between the interface and the specified destination address. Options ipAddress—Destination IP address that the router uses to identify packets for this interface ipAddressMask—Network mask for associated IP subnet deny—Filters packets matching this command Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 800: Ip Dhcp-Capture
By default, DHCP packet information is not captured. The no version restores the default behavior. Options all—Captures received and transmitted packets receive—Captures received packets transmit—Captures transmitted packets low—Captured packets arrive with low priority; the default priority high—Captured packets arrive with high priority Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 801: Ip Dhcp-External Auto-Configure
The no version disables the autoconfigure feature. Options agent-circuit-identifier—Creates dynamic subscriber interfaces built over dynamic VLANs that are based on the agent-circuit-id option (suboption 1) of the option 82 field in DHCP messages. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 802: Ip Dhcp-External Disregard-Giaddr-Next-Hop
DHCP server when the next hop for a subscriber's access route is determined. The no version returns to the default, in which DHCP external uses the giaddr to determine the next hop. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 803: Ip Dhcp-External Recreate-Subscriber-Interface
IP interface. Mode Global Configuration Related Topics Preservation of Dynamic Subscriber Interfaces with DHCP External Server Overview Configuring DHCP External Server to Control Preservation of Dynamic Subscriber Interfaces Copyright © 2010, Juniper Networks, Inc.
Page 804: Ip Dhcp-External Server-Address
Configures a DHCP server that is used to determine which DHCP packets are monitored. The no version removes the DHCP server. Options ipAddress—IP address of the external DHCP server; you can specify a maximum of four servers Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 805: Ip Dhcp-External Server-Sync
Command introduced before JunosE Release 7.1.0. Description Creates subscriber state information based on lease renewals when the external DHCP server is unsynchronized with the E Series router. The no version disables this feature. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 806: Ip Dhcp-Local Auth Domain
In standalone mode, the locally configured username is presented to AAA in an authentication request. The no version removes the domain name. Options domainName—String of 1–32 characters used as the domain name Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 807: Ip Dhcp-Local Auth Include
DHCP client's request was received mac-address—Specifies the DHCP client's MAC address option82—Specifies the DHCP client's Option 82 value virtual-router-name—Specifies the DHCP local server's virtual router name Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 808: Ip Dhcp-Local Auth Password
Assigns a password used to authenticate a locally configured DHCP standalone mode client. In DHCP standalone mode, the password is presented to AAA in an authentication request. The no version removes the password. Options password—String of 1–32 characters used as the password Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 809: Ip Dhcp-Local Auth User-Prefix
In DHCP standalone mode, the username is presented to AAA in an authentication request. The no version removes the user prefix. Options userNamePrefix—String of 1–32 characters used as the prefix for a locally configured username Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 810: Ip Dhcp-Local Auto-Configure Agent-Circuit-Identifier
VLANs that are based on the agent-circuit-id option (suboption 1) of the option 82 field in DHCP messages. This command is specific to a virtual router. The no version disables the autoconfigure feature. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 811: Ip Dhcp-Local Cable-Modem
Use the set dhcp vendor-option command to configure the vendor class identifier option to match the string used by cable modems to replace the function of this command. Options ipAddress—IP address of the cable modem DHCP server Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 812: Ip Dhcp-Local Excluded-Address
IP address or start of the range of IP addresses that the DHCP local server should not supply ipAddressStop—End of the range of IP addresses that the DHCP local server should not supply Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 813: Ip Dhcp-Local Limit
“Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 value—Maximum number of leases, in the range 0–96000; default is 48000 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 814: Ip Dhcp-Local Pool
Accesses DHCP Local Pool Configuration mode. The no version prevents the DHCP local server from supplying IP addresses from the specified pool. Options poolName—Name of the address pool default—Specifies the default address pool Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 815: Ip Dhcp-Local Snmptraps
Syntax [ no ] ip dhcp-local snmpTraps Release Information Command introduced before JunosE Release 7.1.0. Description Enables DHCP local server SNMP traps. The no version disables DHCP local server SNMP traps. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 816: Ip Dhcp-Local Unique-Client-Ids
ID or hardware address—the DHCP server processes requests in the normal manner. NOTE: This command replaces the ip dhcp-local inhibit-roaming command, which has been removed from the CLI. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 817: Ip Dhcp-Server
DHCP servers from the list. Options dhcpServerAddress—IP address of the DHCP server that will allocate addresses for remote users adminStatus—One of the following options: disable—Disables the DHCP server drain—Drains the DHCP server Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 818: Ip Directed-Broadcast
[ no ] ip directed-broadcast Release Information Command introduced before JunosE Release 7.1.0. Description Enables translation of directed broadcast to physical broadcasts. The no version disables the function. Mode Interface Configuration, Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 819: Ip Disable-Forwarding
The no version enables forwarding of packets on the SRP Ethernet interface. You see an error message if you try to set this command for interfaces other than the SRP Ethernet interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 820: Ip Domain-Lookup
The no version with the transit-virtual-router option stops a virtual router from using the same name servers you configured for another virtual router. Options vrName—Name of the virtual router that has the DNS configuration you want to use for a second virtual router Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 821: Ip Domain-Name
Defines a default domain name for the clients that a name resolver serves. The no version deletes the domain name; that is, the domain name will no longer be appended to hostnames in the static host table. Options domainName—Default domain name for your hosts Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 822: Ip Dos-Protection-Group
Attaches an IP denial of service (DoS) protection group to an interface. The no version removes the attachment of the DoS protection group from the interface. Options groupName—Name of the DoS protection group; string of up to 31 alphanumeric characters Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 823: Ip Dvmrp
Chapter 10: I Commands ip dvmrp Syntax [ no ] ip dvmrp Release Information Command introduced before JunosE Release 7.1.0. Description Activates DVMRP on an interface. The no version removes DVMRP from an interface. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 824: Ip Dvmrp Accept-Filter
DVMRP route when the router determines the RPF interface for the source of a multicast packet listName2—Name of an access list containing the neighbors from which the router will accept reports. If the name is 0, the interface accepts destinations from all its neighbors. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 825: Ip Dvmrp Announce-Filter
IP access list that specifies the DVMRP routes that the router will advertise on the interface. You can specify a simple or extended access list; with an extended access list you can specify an address and a subnet mask. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 826: Ip Dvmrp Auto-Summary
[ no ] ip dvmrp auto-summary Release Information Command introduced before JunosE Release 7.1.0. Description Summarizes routes automatically on an interface. By default, automatic summarization is enabled. The no version disables automatic summarization. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 827: Ip Dvmrp Disable
[ no ] ip dvmrp disable Release Information Command introduced before JunosE Release 7.1.0. Description Disables DVMRP on an interface without removing the DVMRP configuration. The no version reenables the DVMRP configuration on a disabled interface. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 828: Ip Dvmrp Metric-Offset
DVMRP route advertised in outgoing DVMRP reports increment—Number of hops associated with this interface; default value is 1 for incoming reports and 0 for outgoing reports. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 829: Ip Dvmrp Route-Hog-Notification
Command introduced before JunosE Release 7.1.0. Description Sets the number of DVMRP routes that the router can record before it generates a system log warning message. The no version restores the default setting, 10,000 routes. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 830: Ip Dvmrp Route-Limit
7000. The no version removes the limit for the number of routes that the router can advertise on each interface. Options limit—Number of routes that the router can advertise Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 831: Ip Dvmrp Summary-Address
Advertises a DVMRP summary address on the interface. The no version stops the advertising of a summary address on an interface. Options ipAddress—Summary address mask—Subnet mask cost—Cost associated with this summary address Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 832: Ip Dvmrp Unicast-Routing
Enables the exchange of DVMRP unicast routes on an interface not owned by DVMRP. The no version disables the exchange of DVMRP unicast routes on an interface not owned by DVMRP. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 833: Ip Dynamic-Interface-Prefix
BGP/MPLS VPNs. The no version restores the default prefix, dyn. Options vrfName—Name of the VRF in which the shared interface is created; a string of 1–32 alphanumeric characters prefix—String of 1–10 alphanumeric characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 834: Ip Explicit-Path
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 835: Ip Extcommunity-List
IP address followed by a 16-bit integer *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 836: Ip Fallback Global
Enables secondary routing table lookup for an interface in a virtual router forwarding table of the parent (global) virtual router if the initial route lookup on a VRF is unsuccessful. The no version discontinues secondary routing table lookup. Mode VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 837: Ip Filter-Options All
Enables filtering of packets with IP options on an interface. IP options filtering is disabled by default. The no version disables filtering of packets with IP options. Mode Interface Configuration, Profile Configuration Related Topics Enabling IP Options Filtering Copyright © 2010, Juniper Networks, Inc.
Page 838: Ip Flow-Aggregation Cache
Options as—Specifies autonomous system aggregation destination prefix—Specifies destination prefix aggregation prefix—Specifies prefix aggregation protocol-port—Specifies protocol port aggregation source-prefix—Specifies source prefix aggregation Mode Flow Cache Configuration, Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 839: Ip Flow-Cache Entries
Options cacheEntries—Number of cache entries allowed for all line modules in the router in the range 1024–524288; default value is 65536 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 840: Ip Flow-Cache Timeout
Defines the J-Flow activity or inactivity timers. The no version restores the default value of each timer. Options activeTimer—Value of activity timer in the range 0–60 minutes; default value is 30 inactiveTimer—Value of inactivity timer in the range 10–600 seconds; default value is 15 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 841: Ip Flow-Export
Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 842: Ip Flow-Sampling-Mode Packet-Interval
Options intervalValue—Sampling interval, in the range 1–4000000000 packets; default value is 4000000000 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 843: Ip Flow Statistics
Chapter 10: I Commands ip flow statistics Syntax [ no ] ip flow statistics Release Information Command introduced before JunosE Release 7.1.0. Description Enables J-Flow statistics. The no version disables J-Flow statistics. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 844: Ip Ftp Source-Address
Specifies an operational interface by IP address as the source interface in FTP packets sent via the router's FTP client. The no version restores the source address in the FTP packets to that on which the FTP connection is made. Options sourceAddress—Source IP address Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 845: Ip Ftp Source-Interface
FTP connection is made. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 846: Ip-Hint
The address is then passed as a hint in the authentication request to the RADIUS server. The no version disables the feature. Options enable—Specifies the feature disable—Disables the feature; this is the default setting Mode Domain Map Configuration Copyright © 2010, Juniper Networks, Inc.
Page 847: Ip Http
Chapter 10: I Commands ip http Syntax [ no ] ip http Release Information Command introduced in JunosE Release 7.2.0. Description Creates the HTTP local server. The no version deletes the HTTP local server. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 848: Ip Http Access-Class
Specifies the standard IP access list that identifies the subscribers who are authorized to connect to the HTTP local server. The no version removes the association between the access list and the HTTP local server. Options listName—Name of the access list Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 849: Ip Http Max-Connection-Time
Specifies the maximum time that the HTTP local server maintains an inactive connection. The no version restores the default time. Options seconds—Either 0 (unlimited) or the number of seconds in the range 3–7200; default value is 30 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 850: Ip Http Port
Specifies the port on which the HTTP local server receives connection attempts. The no version restores the default port number. Options portNumber—Number of the port, in the range 0–65535; the default is port 80 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 851: Ip Http Redirecturl
Specifies the URL to which a subscriber's initial Web browser session is redirected, enabling initial provisioning and service selection for the subscriber. The no version removes the redirection action. Options url—Name of the URL; 64 characters maximum Mode Interface Configuration, Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 852: Ip Http Same-Host-Limit
Specifies the maximum number of connections that can exist between one IP address and the HTTP local server. The no version restores the default number of allowed connections. Options maxConnections—Maximum number of connections allowed, in the range 0–1000; the default is 3 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 853: Ip Http Server
Syntax [ no ] ip http server Release Information Command introduced in JunosE Release 7.2.0. Description Enables the HTTP local server. The no version disables the HTTP local server. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 854: Ip Icmp Update-Source
Interface Types and Specifiers on page 5 ipAddress—IP address of an E Series interface over which you want to send ICMP messages Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 855: Ip Igmp
Release Information Command introduced before JunosE Release 7.1.0. Description Enables IGMP on an interface, and sets the IGMP version to IGMPv2. The no version disables IGMP on an interface. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 856: Ip Igmp Access-Group
The no version removes the association with the specified access list and allows hosts on the subnet to join any multicast group. Options accessListName—Name of the access list; a string of up to 32 characters Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 857: Ip Igmp Access-Source-Group
) permitted by the specified IP access list. The no version removes any access list restriction. Options accessListName—Name of the access list; a string of up to 32 characters Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 858: Ip Igmp Apply-Oif-Map
Applies the specified outgoing interface (OIF) map to the current interface. The no version removes the outgoing interface map association from the interface. Options mapName—Name of the OIF map Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 859: Ip Igmp Explicit-Tracking
Options disable-if-igmp-v2-detected—Disables explicit host tracking if IGMP V2 hosts detected on IGMP V3 interfaces Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 860: Ip Igmp Group Limit
IGMP groups that the interface accepts. Options groupLimit—Maximum number of IGMP groups that an interface can accept in the range 0–64,000 Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 861: Ip Igmp Immediate-Leave
CAUTION: Issue this command only on IGMPv2 interfaces to which one IGMP client is connected. Do not issue this command to interfaces to which more than one IGMP client is connected. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 862: Ip Igmp Last-Member-Query-Interval
IGMP leave message and sending out of a query in the range 1–254 tenths of a second. Using a lower value allows members to leave groups more quickly. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 863: Ip Igmp Oif-Map
Interface Types and Specifiers on page 5 self—Specifies that the multicast outgoing interface is the same as IGMP join interface groupPrefix—Group prefix in the form ipAddress/maskLength sourcePrefix—Source prefix in the form ipAddress/maskLength Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 864: Ip Igmp Promiscuous
Options on—Enables the interface to accept IGMP reports from hosts on any subnet off—Allows the interface to accept IGMP reports only from hosts on subnets associated with this interface Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 865: Ip Igmp-Proxy
Enables IGMP proxy on an interface and specifies the version. Version 2 is enabled by default. The no version disables IGMP proxy for an interface. Options 2—Specifies IGMP proxy version 2 3—Specifies IGMP proxy version 3 Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 866: Ip Igmp-Proxy Unsolicited-Report-Interval
400 tenths of a second. NOTE: Issue this command only on the upstream interface. Otherwise, this command will have no effect. Options tenths-of-a-second—Time interval at which the interface transmits unsolicited reports Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 867: Ip Igmp-Proxy V1-Router-Present-Time
10 seconds. Options seconds—Time for which the router assumes that there is an IGMPv1 querier router on the subnet after the router receives an IGMP V1 query on this interface Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 868: Ip Igmp Querier
The no version specifies that this interface will not issue query packets. NOTE: This command is valid only for interfaces on configured with IGMPv1. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 869: Ip Igmp Querier-Timeout
Sets the time that the interface waits before declaring itself as the querier. The no version restores the default value, twice the query interval. Options seconds—Time interval between the last query from the previous router and the first query from this interface Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 870: Ip Igmp Query-Interval
Sets how often the router sends IGMP host-query packets from this interface. The no version restores the default value, 125 seconds. Options seconds—Polling interval in the range 0–65535 seconds Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 871: Ip Igmp Query-Max-Response-Time
100 tenths of a second (10 seconds). Options tenthsOfaSecond—Time interval between receipt of an IGMP query and the response; in the range 1–254 tenths of a second. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 872: Ip Igmp Robustness
The no version restores the default value, 3. Options numberOfMessages—Number of times that the router sends IGMP group-specific queries in the range 1–4 Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 873: Ip Igmp Ssm-Map Enable
PIM SSM. SSM mapping allows the router to use a statically configured list to translate (* ,G) memberships to (S,G) memberships. The no version disables the SSM map. Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 874: Ip Igmp Ssm-Map Static
(* ,G) memberships to (S,G) memberships. The no version removes the SSM map association. Options accessListName—Name of the access control list sourceAddress—Address of the source Mode Privileged Exec, User Exec Copyright © 2010, Juniper Networks, Inc.
Page 875: Ip Igmp Static-Exclude
Specifies that an interface not handle multicast traffic for one or more (S,G) combinations. The no version removes the (S,G) exclusion from the interface. Options sourceAddress—Address of the source groupAddress—Address of the group Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 876: Ip Igmp Static-Group
Assigns an interface to handle all multicast traffic for a group. The interface sets no timers for this group. The no version removes the group from the interface. Options groupAddress—Address of the group Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 877: Ip Igmp Static-Include
Assigns an interface to handle multicast traffic for one or more (S,G) combinations. The no version removes the (S,G) association from the interface. Options sourceAddress—Address of the source groupAddress—Address of the group Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 878: Ip Igmp Version
Sets the IGMP version for the interface. The no version restores the default value, IGMPv2. Options 3—Specifies IGMP version 3 2—Specifies IGMP version 2 1—Specifies IGMP version 1 passive—Configures a mapped OIF as a passive interface with only multicast-data-forwarding capability Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 879: Ip Ignore-Df-Bit
The no version restores the default behavior, which is to consider the DF bit before fragmenting. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 880: Ip Inactivity-Timer
The no version disables the timer. Options inactiveTime—Length of time in the range 0–63335 minutes; a value of 0 specifies that dynamically created subscriber interfaces are not deleted Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 881: Ip Initial-Sequence-Preference
Configures the warm restart replay preference for an IP interface after a high availability switchover. The no version restores the default value. Options preference—Preference value, 0 or 1; 1 indicates highest preference; default value is 0 Mode Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 882: Ip Interface
JunosE 11.2.x Command Reference Guide A to M ip interface Syntax no ip interface Description This command has only a no version. See the no ip interface command for a complete description. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 883: Ip Irdp
[ no ] ip irdp Release Information Command introduced before JunosE Release 7.1.0. Description Enables ICMP Router Discovery Protocol processing on an interface. The no version disables IRDP routing. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 884: Ip Local Alias
1–16 characters that defines an alias name for the local address pool poolName—Text string in the range 1–16 characters that is the name of the local address pool Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 885: Ip Local Pool
1–100; default value is abatedUtilization—Abated utilization value; a number in the range 1–100; default value is 75 snmpTrap—Enables SNMP pool utilization traps Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 886: Ip Local Pool Snmptrap
Description Enables SNMP pool utilization traps. The no version disables SNMP pool utilization traps. Options name—Text string in the range 1–16 characters that defines the name of the local address pool Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 887: Ip Local Pool Warning
1–100; default value is 85 abatedUtilization—Abated utilization value; a number in the range 1–100; default value is 75 snmpTrap—Enables snmp pool utilization traps Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 888: Ip Local Shared-Pool
DHCP local server address pool. dhcpPoolName—Text string in the range 1–64 characters that defines the name of the DHCP local address pool that provides addresses to the shared local address pool. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 889: Ip Mac-Validate
IP packets to pass through even though the packets do not have entries in the validation table; only packets that have matching IP–MAC pair entries in the table are validated; this is the default setting Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 890: Ip Mask-Reply
JunosE 11.2.x Command Reference Guide A to M ip mask-reply Syntax [ no ] ip mask-reply Release Information Command introduced before JunosE Release 7.1.0. Description Enables ICMP netmask reply. The no version disables the feature. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 891: Ip Match-Policy-List
Creates an IP policy list and launches the policy list configuration mode. The no version deletes the policy list. Options policyList—Name of the policy list permit—Defines the policy list as a permit deny—Defines the policy list as a deny Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 892: Ip Mirror
IP address to the remote analyzer host; required if the analyzer interface is a shared medium, such as Ethernet Mode Global Configuration Related Topics Configuring CLI-Based Mirroring Copyright © 2010, Juniper Networks, Inc.
Page 893: Ip Mobile Home-Agent
T bit registration requests. By default, reverse tunneling is enabled on the router. When you modify support for reverse tunnels, the modification takes effect only for subsequently accepted registration requests Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 894: Ip Mobile Host
ACL lifetimeSeconds—Maximum number of seconds during which the registration requests are established; default value is 36,000 seconds. The maximum lifetime configured for specific mobile nodes can override this lifetime value Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 895: Ip Mobile Profile
IP signaling. The no version removes the profile configuration from the virtual router. Options profileName—Name of the profile associated with the home agent for Mobile IP signaling in a virtual router Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 896: Ip Mobile Secure Foreign-Agent
7 seconds hmac-md5—Specifies the authentication algorithm for Mobile IP messages, default value is hmac-md5 keyed-md5—Specifies the authentication algorithm for Mobile IP messages Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 897: Ip Mobile Secure Host
1–255, by which a registration request can exceed the home agent configured time value; default value is 7 seconds hmac-md5—Specifies the authentication algorithm for Mobile IP messages, default value is hmac-md5 keyed-md5—Specifies the authentication algorithm for Mobile IP messages Copyright © 2010, Juniper Networks, Inc.
Page 898 JunosE 11.2.x Command Reference Guide A to M Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 899: Ip Mpls Forwarding-Mode Label-Switched
NOTE: For some types of routes, the router always generates a per-VRF label, regardless of the status of this command. See Creating labels per FEC in the JunosE BGP and MPLS Configuration Guide, for details. Mode VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 900: Ip Mtu
160–10240; default value is 0, which means that the router takes the value from a lower protocol layer Mode Interface Configuration, Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 901: Ip Multicast Admission-Bandwidth-Limit
Specifies multicast admission bandwidth (in kilobits per second) for a given interface. The no version removes the admission bandwidth limit. Options limitValue—Maximum admission bandwidth (in kilobits per second) permitted on an interface; default value is 0, which disables the limit Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 902: Ip Multicast Ioa-Packet-Replication
I/O module or IOA. The no version disables hardware multicast packet replication. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 903: Ip Multicast-Routing
[ no ] ip multicast-routing Release Information Command introduced before JunosE Release 7.1.0. Description Enables IP multicast routing on the router. The no version disables IP multicast routing on the router. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 904: Ip Multicast-Routing Bandwidth-Map
Enables the QoS adjust function on the router. The no version disables the QoS adjust function on the router. Options routeMapName—Name of the route map you want to use for the bandwidth map Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 905: Ip Multicast-Routing Disable-Rpf-Check
Disables RPF checks for the (S,G) pairs in the specified access list. The no version restores the default situation, in which the router performs RPF checks for all (S,G) pairs. Options ipAccessList—Name of the IP access list that specifies the (S,G) pairs Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 906: Ip Multicast-Routing Permanent-Mroute
However, it does not remove any existing permanent mroutes. To remove existing permanent mroutes, use the clear ip mroute command. Options accessListName—Name of the IP access list that contains the mroutes Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 907: Ip Multipath Round-Robin
[ no ] ip multipath round-robin Release Information Command introduced before JunosE Release 7.1.0. Description Specifies round-robin as the mode for ECMP load sharing on an interface. The no version restores the default value, hashed. Mode Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 908: Ip Name-Server
The no version deletes the name server. Options serverIpAddress—IP or IPv6 address of a DNS name server *—Indicates that one or more parameters can be repeated multiple times in a list in the command line Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 909: Ip Nat
The inside portion of the network uses nonroutable IP addresses. outside—Specifies that the interface resides on the outside (public) portion of the network. The outside portion of the network (for example, the Internet) uses routable legitimate addresses. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 910: Ip Nat Inside Source List
NAT IP address pool that contains addresses you want to use when translating matched access list addresses overload—Specifies that the translation process create extended translation table entries (IP address, protocol, and port values) Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 911: Ip Nat Inside Source Static
Options tcp—Indicates a TCP port udp—Indicates a UDP port localIpAddress—Inside local address localPort—Inside local TCP or UDP port globalIpAddress—Inside global address globalPort —Inside global TCP or UDP port Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 912: Ip Nat Outside Source List
NAT IP address pool that contains addresses you want to use when translating matched access list addresses Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 913: Ip Nat Outside Source Static
Options tcp—Indicates a TCP port udp—Indicates a UDP port globalIpAddress—Inside global address globalPort—Inside global TCP or UDP port localIpAddress—Inside local address localPort—Inside local TCP or UDP port Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 914: Ip Nat Pool
NAT pool ranges you specify length—Length of the network prefix; the number of bits masking the base address that results in the address that you want to match Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 915: Ip Nat Translation
ICMP protocol translations; default value is 300 seconds (5 minutes) gre-timeout—Sets aging time for GRE protocol translations; default value is 300 seconds (5 minutes) seconds—Number of seconds before the router removes an unused NAT table entry Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 916: Ip Nat Translation Max-Entries
The no version removes the configured limit. Options maximumEntryNumber—Maximum number of translation entries in the current virtual router; default value is no limit Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 917: Ip Nfs
E Series interface that sends and receives NFS communications interfaceType—Interface type; see “Interface Types and Specifiers” on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 918: Ip Nfs Host
0–4294967295 that a user must enter to connect to the remote host; default value is 2001 groupID—Group identity in the range 0–4294967295 that the user must enter to connect to the remote host; default value is 100 Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 919: Ip Ospf Authentication-Key
Description Assigns a password used by neighboring routers that are using OSPF simple password authentication. The no version deletes the password. Options authKey—Password; string of up to 8 characters Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 920: Ip Ospf Authentication Message-Digest
Command introduced before JunosE Release 7.1.0. Description Specifies that the authentication mode for the interface is MD5. The no version sets authentication for the interface to none, but leaves any configured MD5 key intact. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 921: Ip Ospf Authentication-None
Release Information Command introduced before JunosE Release 7.1.0. Description Specifies that no authentication is to be used for the interface. The no version has no effect. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 922: Ip Ospf Bfd-Liveness-Detection
BFD packets that can be missed before the BFD session is declared down; number in the range 1–255; default value is 3 Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 923: Ip Ospf Cost
Specifies a cost metric for an interface. Used in the calculation of the SPF routing table. The no version resets the path cost to the default. Options intfCost—Link-state metric cost; number in the range 0–65535; default value is 10 Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 924: Ip Ospf Dead-Interval
The no version resets the dead interval to its default. Options deadInterval—Number in the range 0–2147483647 seconds; default value is 40 seconds Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 925: Ip Ospf Hello-Interval
Specifies the interval between hello packets that the router sends on the interface. The no version resets the hello interval to its default. Options helloInterval—Number in the range 1–65535 seconds; default value is 10 seconds Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 926: Ip Ospf Message-Digest-Key Md5
0—Indicates the msgDigestKey is entered in unencrypted form (plaintext); this is the default option 8—Indicates the msgDigestKey is entered in encrypted form (ciphertext) msgDigestKey—OSPF password; string of up to 16 alphanumeric characters Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 927: Ip Ospf Network
The no version restores the default value for the medium. Options broadcast—Sets the network type to broadcast non-broadcast—Sets the network type to NBMA point-to-point—Sets the network type to point-to-point Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 928: Ip Ospf Priority
This designation applies only to multiaccess networks. Every broadcast and nonbroadcast multiaccess network has a designated router. The no version restores the default value. Options intfPriority—Priority value, an 8-bit number in the range 1–255; default value is 1 Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 929: Ip Ospf Retransmit-Interval
Specifies the time between LSA retransmissions for the interface when an acknowledgment for the LSA is not received. The no version restores the default value. Options retransInterval—Number in the range 0–3600 seconds; default value is 5 seconds Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 930: Ip Ospf Shutdown
Syntax [ no ] ip ospf shutdown Release Information Command introduced before JunosE Release 7.1.0. Description Disables OSPF on an interface. The no version enables OSPF on the interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 931: Ip Ospf Transmit-Delay
Sets the estimated time it takes to transmit a link-state update packet on the interface. The no version restores the default value. Options transmDelay—Link-state transmit delay, a number in the range 0–3600 seconds; default value is 1 second Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 932: Ip Pim
PIM interface for a dynamic profile. The no version disables PIM on an interface. Options dense-mode—Enables PIM in dense mode sparse-mode—Enables PIM in sparse mode sparse-dense-mode—Enables PIM in sparse-dense mode Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 933: Ip Pim Bfd-Liveness-Detection
BFD liveness detection interval; equal to the number of BFD packets that can be missed before the BFD session is declared down; number in the range 1–255; default value is 3 Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 934: Ip Pim Bsr-Candidate
0–255 of the BSR-Priority field of BSMs that the router originates; default value is 0 bootstrapPeriod—Interval in the range 1–65535 seconds at which the BSR sends bootstrap messages; default value is 60 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 935: Ip Pim Data-Mdt
[ no ] ip pim data-mdt Release Information Command introduced in JunosE Release 8.2.0. Description Activates data MDTs and enters IP PIM Data MDT Configuration mode. The no version deactivates data MDTs. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 936: Ip Pim Dr-Priority
Router Configuration mode, then the default value of 1 is restored. NOTE: You cannot configure the designated router priority on PIM dense mode interfaces. Options priority—Value in the range 1–254; default value is 1. Mode Interface Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 937: Ip Pim Group-Address-Pool
Configures PIM group address pools from which data MDT group addresses are allocated. The no version removes the group address pool. Options poolName—Name of the group address pool groupAddressMinimum—Minimum value in the group address range groupAddressMaximum—Maximum value in the group address range Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 938: Ip Pim Join-Filter
Options accessListName—Name of the access list that you want this interface to use as a PIM join filter; a string of up to 32 alphanumeric characters Mode Global Configuration, Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 939: Ip Pim Join-Prune-Interval
NOTE: You cannot configure the designated router priority on PIM dense mode interfaces. Options interval—Interval in the range 10–210 seconds at which the router sends the PIM join/prune message; the default value is 60 seconds. Mode Interface Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 940: Ip Pim Query-Interval
Specifies how often the router sends PIM router query messages from this interface. The no version specifies the default time interval, 30 seconds. Options queryTime—Interval in the range 0–210 seconds at which the router sends PIM router query messages from this interface Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 941: Ip Pim Rp-Address
RP router ipAccessList—Name of the IP access list that specifies which multicast groups use this override—Specifies that this static RP mapping has priority over group-to-RP mappings learned by auto-RP Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 942: Ip Pim Rp-Candidate
In the RP election process, the RP with the lower priority value is preferred; default value is 192 interval—Interval in the range 1–65535 seconds at which the C-RP sends advertisement messages to the BSR; default value is 60 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 943: Ip Pim Send-Rp-Announce
IP access list that specifies which multicast groups use this RP; default value is no access list seconds—Time interval in the range 1–65535 seconds at which the router sends the announcements; default value is 60 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 944: Ip Pim Send-Rp-Discovery Scope
“Interface Types and Specifiers” on page 5. If you specify an interface, the autoRP discovery messages will contain the IP address for this interface. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 945: Ip Pim Sparse-Mode Graceful-Restart-Duration
Sets duration time for IP PIM sparse-mode graceful restart. The no version resets the duration to the default. Options sparse-mode—Enables PIM in sparse mode seconds—Restart duration in seconds; default value is 30 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 946: Ip Pim Spt-Threshold
SPT infinity—Prevents PIM sparse mode from switching from a shared tree to an SPT ipAccessList—Name of the IP access list that specifies the groups to which the threshold applies Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 947: Ip Pim Ssm
SSM on the router. Options default—Specifies that SSM use the IANA-specified range of 232/8 ipAccessList—Name of the IP access list that specifies the range of multicast addresses you want SSM to use Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 948: Ip Policy
In Profile Configuration mode, the no version removes policy reference from the profile. Options input—Applies policy to data arriving at this interface before a route lookup output—Applies policy to data leaving this interface Copyright © 2010, Juniper Networks, Inc.
Page 949 NOTE: The local-input keyword for the ip policy command is deprecated, and might be completely removed in a future release. We recommend that you remove the keyword from scripts. Mode Interface Configuration, Profile Configuration Related Topics Setting a Statistics Baseline for Policies Configuring CLI-Based Mirroring Copyright © 2010, Juniper Networks, Inc.
Page 950: Ip Policy-List
Attaching this policy list to an interface filters all packets on that interface. The no version removes a policy list. Options policyName—Name of the policy list Mode Global Configuration Related Topics Creating Policy Lists for IP Copyright © 2010, Juniper Networks, Inc.
Page 951: Ip Policy-Parameter Hierarchical
Aggregation node number in the range 1–65535 vpValue—ATM VPI number in the range 0–255 svlanValue—S-VLAN ID number in the range 0–4095 Mode Interface Configuration, Profile Configuration Related Topics Creating a Classifier Group for a Policy List Copyright © 2010, Juniper Networks, Inc.
Page 952: Ip Policy-Parameter Reference-Rate
40 characters increase—Increments the existing reference rate value value—Value of the reference rate parameter, in the range 0–4292967295 Mode Interface Configuration, Profile Configuration Related Topics Creating a Classifier Group for a Policy List Copyright © 2010, Juniper Networks, Inc.
Page 953: Ip Prefix-List
32 leNumber—Route being filtered matches if its prefix is within the range specified: greater than or equal to length and less than or equal to leNumber Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 954: Ip Prefix-Tree
192.168.32.0 or 10.10.0.0 length—Length of the network prefix; number of bits masking base address to produce address to be matched Mode Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 955: Ip Profile
The no version removes the association with this profile. Options profileName—Name of the profile that you want the IPSec layer to pass to the IP layer upon request for upper-layer instantiation Mode IPSec Tunnel Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 956: Ip Proxy-Arp
Enables proxy ARP on an Ethernet or bridge1483 interface. Proxy ARP is enabled by default. The no version disables proxy ARP on an Ethernet or bridge1483 interface. Options restricted—Restricts proxy-arp to hosts on the local interface unrestricted—Enables proxy-arp for all reachable hosts Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 957: Ip Re-Authenticate-Auto-Detect Ip-Subscriber
IP subscriber interfaces using the DHCP options dhcp-options, dhcp-gi-address, and dhcp-mac-address when the DHCP external application manages the subscriber addresses following a cold boot. The no version negates the command or restores the defaults. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 958: Ip Redirects
Enables the sending of redirect messages if the software is forced to resend a packet through the same interface on which it was received. The no version disables the sending of redirect messages. Mode Interface Configuration, Profile Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 959: Ip Refresh-Route
Command introduced before JunosE Release 7.1.0. Description Reinstalls routes removed from the IP routing table by the clear ip route command. There is no no version. Options vrfName—Name of the VRF; string of 1–32 alphanumeric characters Mode Privileged Exec Copyright © 2010, Juniper Networks, Inc.
Page 960: Ip Rip
Configures RIP to run on the network specified by the network command. Uses the default values: send version is RIP version 1, receive version is RIP version 1 and version 2, authentication is not enabled. The no version deletes the RIP interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 961: Ip Rip Authentication Key
8—Indicates the authKey is entered in encrypted form (ciphertext) authkey—Password sent with RIP messages or the key used to encrypt/decrypt RIP messages, depending on the authentication mode set for this interface Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 962: Ip Rip Authentication Mode
RIP message with MD5 message-digest algorithms keyID—Number identifying the MD5 key; neighbors must share the MD5 key to decrypt the message and encrypt the response Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 963: Ip Rip Bfd-Liveness-Detection
BFD liveness detection interval; equal to the number of BFD packets that can be missed before the BFD session is declared down; number in the range 1–255; default value is 3 Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 964: Ip Rip Copy-To-Dynamic
(that refer to numbered IP interface for configuration data) to obtain RIP attributes from the numbered IP interface to which they refer. The no version disables the feature but does not remove all existing, active RIP interfaces that were created by this command. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 965: Ip Rip Receive Version
1—Specifies RIP version 1 only 2—Specifies RIP version 2 only 1 2—Specifies RIP version 1 and version 2 2 1—Specifies RIP version 2 and version 1 off—Turns reception off Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 966: Ip Rip Send Version
1—Specifies RIP version 1 only 2—Specifies RIP version 2 only 1 2—Specifies RIP version 1 and version 2 2 1—Specifies RIP version 2 and version 1 off—Turns reception off Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 967: Ip Route
RTR operation is currently reachable rtrIndex—Number of the RTR operation to be verified; there is no default value Copyright © 2010, Juniper Networks, Inc.
Page 968 BFD packets that can be missed before the BFD session is declared down; number in the range 1–255; default value is 3 Mode Global Configuration, VRF Configuration Copyright © 2010, Juniper Networks, Inc.
Page 969: Ip Route-Cache Flow Sampled
Command introduced before JunosE Release 7.1.0. Profile Configuration mode added in JunosE Release 7.2.0. Description Enables J-Flow statistics on an interface. The no version disables J-Flow statistics on the interface. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 970: Ip Route-Map Ip-Subscriber
IP interface subscriber. If no route map is specified, then all packets will trigger the creation of a dynamic subscriber interface. The no version deletes the route map. Options routeMapName—Name of route map Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 971: Ip Route-Type
BGP both—Specifies that routes for the protocol are available for both unicast forwarding and multicast route path forwarding checks Mode Address Family Configuration (RIP), Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 972: Ip Router-Id
Mode Global Configuration Related Topics Configuring the Loopback Interface and Router ID for BGP for L2VPNs and Configuring the Loopback Interface and Router ID for VPLS in the JunosE BGP and MPLS Configuration Guide Copyright © 2010, Juniper Networks, Inc.
Page 973: Ip Router Isis
If not specified, a null tag is assumed. The name must be unique among all IP router processes for a given router. Use the same text for the argument tag as specified in the router isis command. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 974: Ip-Router-Name
Assigns an IPv4 virtual router. The no version restores the default router. NOTE: This command replaces the deprecated router-name command, which may be removed completely in a future release. Options vrName—Name of the virtual router; string of 1–32 alphanumeric characters Mode Domain Map Configuration Copyright © 2010, Juniper Networks, Inc.
Page 975: Ip Rpf-Route
Interface Types and Specifiers on page 5 distanceValue—Number in the range 0–255 that indicates the preference for this route tagValue—Number in the range 0–4294967295 that identifies the route in the routing table Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 976: Ip Rsvp Authentication
Command introduced before JunosE Release 7.1.0. Description Enables MD5 authentication on the RSVP interface in implementations on routers from other vendors. See the mpls rsvp authentication command for a complete description and syntax. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 977: Ip Rsvp Authentication Key
Command introduced before JunosE Release 7.1.0. Description Assigns a key for MD5 authentication between RSVP peers in implementations on routers from other vendors. See the mpls rsvp authentication key command for a complete description and syntax. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 978: Ip Rsvp Bandwidth
Command introduced before JunosE Release 7.1.0. Description Specifies the total bandwidth reservable on the interface in a non–E Series implementation. See the mpls bandwidth command for a complete description and syntax. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 979: Ip Rsvp Bfd-Liveness-Detection
Enables BFD (bidirectional forwarding detection) on an interface running RSVP-TE and defines BFD values to be negotiated between RSVP-TE neighbors for detection of IP data path failures. See the mpls rsvp bfd-liveness-detection command for a complete description and syntax. Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 980: Ip Rsvp Signalling Hello
Command introduced in JunosE Release 7.3.0. Description Turns on or configures RSVP-TE hello support. See the mpls rsvp signalling hello command for a complete description and syntax. Mode Global Configuration, Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 981: Ip Sa-Validate
This interface must match the interface that the packet arrived on. If it does not match, the router drops the packet. The no version disables source address validation. Mode Interface Configuration, Profile Configuration Copyright © 2010, Juniper Networks, Inc.
Page 982: Ip Sa-Validate Trap-Enable
Enables the generation of source address validation failure traps. The no version disables the generation of source address validation failure traps. Options vrfName—Name of the VRF; string of 1–32 alphanumeric characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 983: Ip Service-Profile
Command introduced before JunosE Release 7.1.0. Description Specifies a service profile used in the route map and enters Service Profile configuration mode. The no version deletes the profile. Options profileName—Name of service profile Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 984: Ip Share-Interface
The no version removes the association between the layer 2 interface and the shared IP interface. Options interfaceType—Interface type; see Interface Types and Specifiers on page 5 interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers on page 5 Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 985: Ip Share-Nexthop
The no version halts tracking of the next hop. Options ipAddress—IP address of the destination for which the next hop is tracked vrName—Name of the virtual router for the next hop Mode Interface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 986: Ip Shutdown
JunosE 11.2.x Command Reference Guide A to M ip shutdown Syntax [ no ] ip shutdown Release Information Command introduced before JunosE Release 7.1.0. Description Shuts down an IP interface. The no version restarts the interface. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 987: Ip Source-Prefix
The no version removes the association between the interface and the specified IP address and mask. Options ipAddress—IP address of the physical interface that receives messages for this subscriber ipAddressMask—Network mask for associated IP subnet deny—Filters packets matching this command Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 988: Ip Source-Route
Enables the forwarding of source-routed packets in a VR or VRF. The no version disables forwarding. Forwarding is disabled by default in all VRs. Options vrfName—Name of the VRF; string of 1–32 alphanumeric characters Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 989: Ip Speed
Sets the speed of an IP interface in bits per second. The no version restores the default value, 0 bps. Options adminSpeed—Speed of the interface in bps in the range 1–4294967295 Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 990: Ip Split-Horizon
Enables split horizon, preventing the RIP router from advertising routes from the interface originating the route, reducing the possibility of routing loops; this is the default condition. The no version disables split horizon. Mode Interface Configuration, Subinterface Configuration Copyright © 2010, Juniper Networks, Inc.
Page 991: Ip Ssh Authentication-Retries
The no version restores the default value, 20 retries. Options retryLimit—Number of times authentication can be retried after the initial failure within a given connection attempt Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 992: Ip Ssh Crypto
3des-cbc, twofish-cbc, and blowfish-cbc cipherAlgorithm—Algorithm to add to the list Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 993: Ip Ssh Disable-User-Authentication
Release Information Command introduced before JunosE Release 7.1.0. Description Disables RADIUS password authentication, resulting in the acceptance of all SSH clients that pass protocol negotiation. The no version restores RADIUS authentication. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 994: Ip Ssh Mac
Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 995: Ip Ssh Sleep
Connection attempts from the user at the same host are denied until this period expires. The no version restores the default value, 600 seconds. Options sleepPeriod—Period in the range 0–4294967295 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 996: Ip Ssh Timeout
Sets a timeout period in seconds. The SSH server terminates the connection if protocol negotiation—including user authentication—is not complete within this timeout. The no version restores the default value, 600 seconds. Options timeout—Period in the range 10–600 seconds Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 997: Ip Ssh User-Authentication-Protocol
Configures the SSH user authentication protocol. E Series routers support RADIUS and TACACS+ user authentication protocols. The no version restores the SSH user authentication protocol to the default, RADIUS. Options protocol—User authentication protocol: either RADIUS or TACACS+. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 998: Ip Static-Route Table-Map
Filters static routes before adding them to the routing table. The no version deletes the table map. Options vrfName—Name of the VRF; string of 1–32 alphanumeric characters mapName—Name of the table map that you want the router to use Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.
Page 999: Ip Summary-Address
Series implementations ipAddress—IP address identifying the route to be summarized ipAddressMask—Network mask identifying the route to be summarized metric—Specifies a metric for the summary address; default value is 1 Mode Address Family Configuration, Router Configuration Copyright © 2010, Juniper Networks, Inc.
Page 1000: Ip Tcp Ack-Rst-And-Syn
The ip keyword for tcp commands is now optional (with the exception of the ip tcp adjust-mss command, which is IPv4 specific). For information about this command and any other ip tcp command, see the tcp commands. Mode Global Configuration Copyright © 2010, Juniper Networks, Inc.

This manual is also suitable for:

Junose 11.2