Siemens SINAMICS S110 List Manual page 754

Parameter
Symbol Meaning
Parameter name [Unit]
Monitoring parameter
rxxxx [x...y]
(parameter may appear .
Parameter name [Unit]
Index name
Monitoring parameter
rxxxx[x] with index.
[aaaa.b]
Setting parameter
Parameter name
from ... to [Unit] (if the parameter appears
a multiple number of times,
pxxxx[y...z] (Def)
then diagram references
are specified).
[aaaa.b]
Parameter name
Index name
Setting parameter with
from ... to [Unit]
index (if the parameter
pxxxx[y] (Def)
appears a multiple number
of times, then diagram
references are specified).
Data sets
Symbol Meaning
pxxxx[C]
Parameter belongs to the
Command Data Set (CDS).
pxxxx[D]
Parameter belongs to the
Drive Data Set (DDS).
pxxxx[E]
Parameter belongs to the
Encoder Data Set (EDS).
pxxxx[M]
Parameter belongs to the
Motor Data Set (MDS).
pxxxx[P]
Parameter belongs to the
Power unit Data Set (PDS).
1 2
DO: All objects
Explanations for the function diagrams - Explanation of the symbols (Part 1)
Connectors
Symbol Meaning
Name
pxxxx
Connector input CI.
(xxxx)
name
pxxxx[y]
Connector input CI with index [y]
(xxxx [x])
name
pxxxx[y...z]
Connector input CI with index
(xxxx [y])
range [y...z]
name [unit]
Connector output CO with [dimension
rxxxx[y...z]
unit] and index range [y...z].
name [unit]
Connector output CO
rxxxx[y]
[dimension unit] and with index [y]
Information on parameters, binectors, connectors
Symbol Meaning
Parameter name (up to 18 characters)
Parameter name
[dimension unit]
[Unit]
"r" = monitoring parameter. These parameters are read-only
rxxxx[y] or
rxxxx[y...z] or "xxxx" stands for the parameter number
"[y]" specifies the valid index, "[y...z]" specifies the applicable index range
rxxxx[y].ww or
".ww" specifies the bit number (e.g. 0...15).
rxxxx.ww
"p" = setting parameter. These parameters can be changed.
pxxxx[y] or
"xxxx" stands for the parameter number,
pxxxx[y...z] or
"[y]" specifies the applicable index, "[y...z]" specifies the applicable index range
pxxxx[y].ww or
".ww" specifies the bit number (e.g. 0...15).
pxxxx.ww
Value range.
from ... to
(xxxx[y].ww) Parameter number (xxxx) with Index number [y] and bit number .ww.
Factory setting.
(Def)
Factory setting with bit number as prefix.
(Def.w)
[aaaa.b] Diagram references for setting parameters that occur a multiple number of times.
[Function diagram number, signal path]
3 4
Binectors
Connectors/binectors
Symbol
Meaning
Symbol
Parameter name
rxxxx
Name
rxxxx
pxxxx
Binektoreingang BI
(Def) Werkseinstellung (Def).
Cross references between diagrams
Name
Symbol
Binector input BI with
pxxxx[y]
index [y] and factory
(Def) Signal path
setting (Def).
Name
Text
pxxxx[y...z] Binector input BI with
(Def) index range [y...z] and
factory setting (Def).
[cccc.d]
Name
rxxxx Binector output BO.
Cross references for control bits
name
Symbol
Binector output BO with
rxxxx.y
bit y.
pxxxx
[aaaa.b]
Sampling times
Symbol
PROFIdrive sampling time
CAN bus sampling time
5 6
fp_1020_98_eng.vsd
28.05.10 V04.04.00
Meaning
Connector/binector output CO/BO
Meaning
The function diagrams are sub-divided into signal
paths 1...8 in order to facilitate orientation.
Text = Unique signal designation
[aaaa.b]
aaaa = Signal goes to target diagram aaa
b = Signal goes to signal path b
Text = Unique signal designation
Text
cccc = Signal comes from source diagram cccc
d = Signal comes from signal path d
Meaning
pxxxx= Original parameter of signal
aaaa = Signal comes from source diagram aaaa
b = Signal comes from signal path b
Meaning
ZZZ.ZZ μs Fixed time slice.
According to presetting in p2048. (In
synchronous mode, bus clock is valid.)
According to presetting in p2048.
There is no fixed sampling time for this
Background
function. The processing takes place in
Refer to [1020.7]
background. The cycle time depends on
the computational load of the control unit.
Not relevant A static state is displayed here. The
sampling time data is not relevant.
Refer to [1020.7]
7 8
Function diagram
- 1020 -
SINAMICS S110