Siemens SINAMICS S110 List Manual page 738

Parameter
Parameters for data sets
p2150[0...n]
p2153[0...n]
p2155[0...n]
p2156[0...n]
p2161[0...n]
p2162[0...n]
p2163[0...n]
p2164[0...n]
p2166[0...n]
p2167[0...n]
p2174[0...n]
p2175[0...n]
p2177[0...n]
p2181[0...n]
p2182[0...n]
p2183[0...n]
p2184[0...n]
p2185[0...n]
p2186[0...n]
p2187[0...n]
p2188[0...n]
p2189[0...n]
p2190[0...n]
p2192[0...n]
p2194[0...n]
p2195[0...n]
p2196[0...n]
p2201[0...n]
p2202[0...n]
p2203[0...n]
p2204[0...n]
p2205[0...n]
p2206[0...n]
p2207[0...n]
p2208[0...n]
p2209[0...n]
p2210[0...n]
p2211[0...n]
p2212[0...n]
p2213[0...n]
p2214[0...n]
p2215[0...n]
p2216[0...n]
p2230[0...n]
p2237[0...n]
p2238[0...n]
p2240[0...n]
p2247[0...n]
p2248[0...n]
p2502[0...n]
p2503[0...n]
p2504[0...n]
p2505[0...n]
1-738
Hysteresis speed 3 / n_hysteresis 3
Speed actual value filter time constant / n_act_filt T
Speed threshold 2 / n_thresh val 2
On delay, comparison value reached / t_on cmpr val rchd
Speed threshold 3 / n_thresh val 3
Hysteresis speed n_act > n_max / Hyst n_act>n_max
Speed threshold 4 / n_thresh val 4
Hysteresis speed 4 / n_hysteresis 4
Off delay n_act = n_set / t_del_off n_i=n_so
Switch-on delay n_act = n_set / t_on n_act=n_set
Torque threshold value 1 / M_thresh val 1
Motor locked speed threshold / Mot lock n_thresh
Motor locked delay time / Mot lock t_del
Load monitoring response / Load monit resp
Load monitoring speed threshold value 1 / n_thresh 1
Load monitoring speed threshold value 2 / n_thresh 2
Load monitoring speed threshold value 3 / n_thresh 3
Load monitoring torque threshold 1, upper / M_thresh 1 upper
Load monitoring torque threshold 1, lower / M_thresh 1 lower
Load monitoring torque threshold 2, upper / M_thresh 2 upper
Load monitoring torque threshold 2, lower / M_thresh 2 lower
Load monitoring torque threshold 3, upper / M_thresh 3 upper
Load monitoring torque threshold 3, lower / M_thresh 3 lower
Load monitoring delay time / Load monit t_del
Torque threshold value 2 / M_thresh val 2
Torque utilization switch-off delay / M_util t_off
Torque utilization scaling / M_util scal
CO: Technology controller, fixed value 1 / Tec_ctr fix val 1
CO: Technology controller, fixed value 2 / Tec_ctr fix val 2
CO: Technology controller, fixed value 3 / Tec_ctr fix val 3
CO: Technology controller, fixed value 4 / Tec_ctr fix val 4
CO: Technology controller, fixed value 5 / Tec_ctr fix val 5
CO: Technology controller, fixed value 6 / Tec_ctr fix val 6
CO: Technology controller, fixed value 7 / Tec_ctr fix val 7
CO: Technology controller, fixed value 8 / Tec_ctr fix val 8
CO: Technology controller, fixed value 9 / Tec_ctr fix val 9
CO: Technology controller, fixed value 10 / Tec_ctr fix val 10
CO: Technology controller, fixed value 11 / Tec_ctr fix val 11
CO: Technology controller, fixed value 12 / Tec_ctr fix val 12
CO: Technology controller, fixed value 13 / Tec_ctr fix val 13
CO: Technology controller, fixed value 14 / Tec_ctr fix val 14
CO: Technology controller, fixed value 15 / Tec_ctr fix val 15
Technology controller fixed value selection method / Tec_ctr FixVal sel
Technology controller motorized potentiometer configuration / Tec_ctr mop config
Technology controller motorized potentiometer maximum value / Tec_ctrl mop max
Technology controller motorized potentiometer minimum value / Tec_ctrl mop min
Technology controller motorized potentiometer starting value / Tec_ctrl mop start
Technology controller motorized potentiometer ramp-up time / Tec_ctr mop t_r-up
Technology controller motorized potentiometer ramp-down time / Tec_ctrMop t_rdown
LR encoder assignment / Encoder assignment
LR length unit LU per 10 mm / LU per 10 mm
LR motor/load motor revolutions / Mot/load motor rev
LR motor/load motor revolutions / Mot/load motor rev
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
© Siemens AG 2012 All Rights Reserved