Siemens SINAMICS S110 List Manual page 740

Parameter
Parameters for data sets
p0419[0...n]
p0421[0...n]
p0423[0...n]
p0425[0...n]
p0426[0...n]
p0427[0...n]
p0428[0...n]
p0429[0...n]
p0430[0...n]
p0431[0...n]
p0432[0...n]
p0433[0...n]
p0434[0...n]
p0435[0...n]
p0436[0...n]
p0437[0...n]
p0438[0...n]
p0439[0...n]
p0440[0...n]
p0441[0...n]
p0442[0...n]
p0443[0...n]
p0444[0...n]
p0445[0...n]
p0446[0...n]
p0447[0...n]
p0448[0...n]
p0449[0...n]
p0453[0...n]
p0493[0...n]
p0494[0...n]
p2507[0...n]
p2525[0...n]
p4662[0...n]
p4663[0...n]
p4664[0...n]
p4665[0...n]
p4666[0...n]
p4670[0...n]
p4671[0...n]
p4672[0...n]
p4673[0...n]
p4674[0...n]
p4675[0...n]
p4676[0...n]
p4677[0...n]
p4678[0...n]
p4679[0...n]
p4680[0...n]
p4681[0...n]
p4682[0...n]
p4683[0...n]
p4684[0...n]
1-740
Fine resolution absolute value Gx_XIST2 (in bits) / Enc fine Gx_XIST2
Absolute encoder rotary multiturn resolution / Enc abs multiturn
Absolute encoder rotary singleturn resolution / Enc abs singleturn
Encoder, rotary zero mark distance / Enc rot dist ZM
Encoder zero mark differential distance / Enc ZM Dif_dist
Encoder SSI baud rate / Enc SSI baud rate
Encoder SSI monoflop time / Enc SSI t_monoflop
Encoder SSI configuration / Enc SSI config
Sensor Module configuration / SM config
Angular commutation offset / Ang_com offset
Gearbox factor, encoder revolutions / Grbx_fact enc_rev
Gearbox factor, motor/load revolutions / Grbx_fact mot_rev
Encoder SSI error bit / Enc SSI error bit
Encoder SSI alarm bit / Enc SSI alarm bit
Encoder SSI parity bit / Enc SSI parity bit
Sensor Module configuration extended / SM config ext
Squarewave encoder filter time / Enc t_filt
Encoder ramp-up time / Enc ramp-up time
Copy encoder serial number / Copy enc ser_no
Encoder commissioning serial number part 1 / Enc comm ser_no 1
Encoder commissioning serial number part 2 / Enc comm ser_no 2
Encoder commissioning serial number part 3 / Enc comm ser_no 3
Encoder commissioning serial number part 4 / Enc comm ser_no 4
Encoder commissioning serial number part 5 / Enc comm ser_no 5
Encoder SSI number of bits before the absolute value / Enc SSI bit before
Encoder SSI number of bits absolute value / Enc SSI bit val
Encoder SSI number of bits after the absolute value / Enc SSI bit after
Encoder SSI number of bits, filler bits / Enc SSI fill bits
Pulse encoder evaluation zero speed measuring time / Enc_ev z 0 t_meas
Zero mark selection, input terminal / ZM_sel inp_term
Equivalent zero mark, input terminal / ZM_equiv input
LR absolute encoder adjustment status / Abs_enc_adj stat
CO: LR encoder adjustment, offset / Enc_adj offset
Encoder characteristic type / Enc char_type
Encoder characteristic K0 / Enc char K0
Encoder characteristic K1 / Enc char K1
Encoder characteristic K2 / Enc char K2
Encoder characteristic K3 / Enc char K3
Analog sensor configuration / Ana_sens config
Analog sensor input / Ana_sens inp
Analog sensor channel A voltage at actual value zero / Ana_sens A U at 0
Analog sensor channel A voltage per encoder period / Ana_sens A U/per
Analog sensor channel B voltage at actual value zero / Ana_sens B U at 0
Analog sensor channel B voltage per encoder period / Ana_sens B U/per
Analog sensor range limit threshold / Ana_sens lim thr
Analog sensor LVDT configuration / Ana_sens LVDT conf
Analog sensor LVDT ratio / An_sens LVDT ratio
Analog sensor LVDT phase / An_sens LVDT ph
Zero mark monitoring tolerance permissible / ZM_monit tol perm
Zero mark monitoring, tolerance window limit 1 positive / ZM tol lim 1 pos
Zero mark monitoring, tolerance window limit 1 negative / ZM tol lim 1 neg
Zero mark monitoring tolerance window alarm threshold positive / ZM tol A_thr pos
Zero mark monitoring tolerance window alarm threshold negative / ZM tol A_thr neg
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
© Siemens AG 2012 All Rights Reserved