Panasonic ZEQUO 2200 Operating Instructions Manual page 59

 Example
To delete access list profiles:
Zxxx0:admin#delete access_profile profile_id 1
Command: delete access_profile profile_id 1
Success.
Zxxx0:admin#
6.3. config access_profile
 Description
This command is used to configure access list entries.
 Format
config access_profile [profile_id <value 1-6> | profile_name <name 1-32>] [add
access_id [auto_assign | <value 1-256>] [ethernet {[vlan <vlan_name 32> | vlan_id
<vlanid 1-4094>] {mask <hex 0x0-0x0fff>} | source_mac <macaddr> {mask
<macmask>} | destination_mac <macaddr> {mask <macmask>} | 802.1p <value 0-7> |
ethernet_type <hex 0x0-0xffff>}(1) | ip {[vlan <vlan_name 32> | vlan_id <vlanid 1-
4094>] {mask <hex 0x0-0x0fff>} | source_ip <ipaddr> {mask <netmask>} |
destination_ip <ipaddr> {mask <netmask>} | dscp <value 0-63> | [icmp {type <value 0-
255> | code <value 0-255>} | igmp {type <value 0-255>} | tcp {src_port <value 0-
65535> {mask <hex 0x0-0xffff>} | dst_port <value 0-65535> {mask <hex 0x0-0xffff>} |
flag [all | {urg | ack | psh | rst | syn | fin}]} | udp {src_port <value 0-65535> {mask
<hex 0x0-0xffff>} | dst_port <value 0-65535> {mask <hex 0x0-0xffff>}} | protocol_id
<value 0-255> {user_define <hex 0x0-0xffffffff> {mask <hex 0x0-0xffffffff>}}]}(1) |
packet_content {offset_chunk_1 <hex 0x0-0xffffffff> {mask <hex 0x0-0xffffffff>} |
offset_chunk_2 <hex 0x0-0xffffffff> {mask <hex 0x0-0xffffffff>} | offset_chunk_3 <hex
0x0-0xffffffff> {mask <hex 0x0-0xffffffff>} | offset_chunk_4 <hex 0x0-0xffffffff>
{mask <hex 0x0-0xffffffff>}}(1) | ipv6 {class <value 0-255> | flowlabel <hex 0x0-
0xfffff> | source_ipv6 <ipv6addr> {mask <ipv6mask>} | destination_ipv6 <ipv6addr>
{mask <ipv6mask>} | [tcp {src_port <value 0-65535> {mask <hex 0x0-0xffff>} |
dst_port <value 0-65535> {mask <hex 0x0-0xffff>}} | udp {src_port <value 0-65535>
{mask <hex 0x0-0xffff>} | dst_port <value 0-65535> {mask <hex 0x0-0xffff>}} | icmp
{type <value 0-255> | code <value 0-255>}]}(1)] [port [<portlist> | all] | vlan_based
[vlan <vlan_name 32> | vlan_id <vlanid 1-4094>]] [permit {priority <value 0-7>
{replace_priority} | [replace_dscp_with <value 0-63> | replace_tos_precedence_with
<value 0-7>] | counter [enable | disable]} | mirror {group_id <value 1-4>} | deny]
{time_range <range_name 32>} | delete access_id <value 1-256>]
6. Access Control List (ACL) Commands
59