Contents Important Safety Instructions Basic Instructions for the Use of This Product 1. Product Outline 1.1 Features 1.2 Specifications 1.3 Accessories 1.4 Basic operation 2. Part Names and Functions 3. Installation and Configuration 3.1 Using 10GBASE-T 3.2 Installing on level shelves 3.3 Mounting to rack 3.4 Configuration of IP address (Basic) Troubleshooting...
Important Safety Instructions This chapter contains important safety instructions for preventing bodily injury and/or property damage. Please read carefully, and follow them at all times. Severity of bodily injury and/or property damage, which could result from incorrect use of the Ethernet Switch, are explained below. WARNING This symbol indicates a potential hazard that could result in serious injury or death.
Page 4
CAUTION Do not connect any other devices except for 100BASE-TX/1000BASE-T/10GBASE-T devices to the twisted pair ports. Deviation could lead to equipment failure. Do not insert any other modules except for our optional SFP module (PN54021K/PN54023K) and the SFP+ module (PN59021/PN59023) to the SFP+ extension slots.
Page 5
CAUTION This Ethernet Switch is to be periodically serviced in order to maintain its performance. Please assign a product administrator, and be sure to implement periodic maintenance. When doing maintenance, check the inspection chart that is posted on our website which has the requisite items listed on it. When using this Ethernet Switch to design systems, use it after applying ...
Select the appropriate cables and lay them. Communications might be affected by how the cables are laid, and environmental noise. 1. Please note that Panasonic shall not bear any liability whatsoever for any damages (this shall include, but is not limited to, lost earnings, lost opportunities, etc.)
Product Outline ZEQUO 5410DL is a Layer 3 Ethernet Switch with management function having 100BASE-TX/1000BASE-T/10GBASE-T ports and SFP+ extension slots. 1.1 Features Has wire-speed Layer 3 switching function. Ports 1 to 4 are 100BASE-TX/1000BASE-T/10GBASE-T ports corresponding to autonegotiation.
Port LED lights up. When the terminal is not operating normally, for example when power is not supplied to the terminal, the Port LED does not light up. For configuration and management method, please see the PDF version Operating Instructions on Panasonic’s website.
Power cord hook block MAC Address label (POWER1) (POWER2) Back panel Serial number label Ground terminal STACK ID LED 100BASE-TX/1000BASE-T/10GBASE-T port Stacking port ZEQUO 5410DL CONSOLE POWER1 Front panel 9600.N.8.1(DTE) STACK ID POWER2 STATUS SD CARD SLOT SD CARD SD card slot...
Page 11
Flow control : None Transmission connector : RJ45 Use our optional RJ45-DSub 9-pin console cable (PN72001) for the console cable. POWER1 LED Port LED POWER2 LED STACK ID LED ZEQUO 5410DL CONSOLE POWER1 9600.N.8.1(DTE) STACK ID POWER2 STATUS SD CARD SLOT SD CARD ...
Installation and Configuration 3.1 Using 10GBASE-T 10GBASE-T was established as per the IEEE 802.3an-2006 standard, and depending upon the twisted pair cables, it is an Ethernet standard whereas communications are transmissible at 10 Gbps, up to maximum of a 100 m. (1) Supported cable types Cable type Transmission distance...
3.4 Configuration of IP address (Basic) (1) Connect this Ethernet Switch and PC with a RJ45–DSub 9-pin console cable and start up the terminal emulator (ZEQUO assist Plus, etc.). (2) Pressing Enter key 1 time opens Login screen. Enter UserName and Password (the default is "manager"...
Page 14
Installation and Configuration For detailed settings and administration methods, please see the PDF version of the Operating Instructions on Panasonic’s website. - Detailed configuration and management methods using the CLI. - Configuration and management method from ZEQUO assist Plus.
Are all of the firmware versions for the devices that are connected to the stacks identical? * Please refer to the instruction manual on the ZEQUO assist Plus on Panasonic’s website in regard to settings and management methods.