Subaru LEGACY 2006 Manual page 3412

asieps_tobira.book 16 ページ ２００９年１０月２６日 月曜日 午前９時１６分
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
3. CLEAR MEMORY MODE
1) On the «Main Menu» display screen, select the
{Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display
screen, select the {Transmission} and press the
[YES] key.
3) Press the [YES] key after the information of
transmission type is displayed.
4) On the «Transmission Diagnosis» display
screen, select the {Clear Memory} and press the
[YES] key.
NOTE:
If {Clear Memory 2} is selected and performed,
DTC and learned control memory are cleared. If
Clear Memory 2 is performed, execute the advance
operation of learning control. <Ref. to 4AT(diag)-
16, FACILITATION OF LEARNING CONTROL,
OPERATION, Subaru Select Monitor.>
4. FACILITATION OF LEARNING CON-
TROL
1) Shift the select lever to "P" range, and apply the
parking brake.
2) Lift-up the vehicle.
3) Connect the Subaru Select Monitor to the data
link connector, and then turn the ignition switch to
ON.
4) Perform {Clear Memory 2} using the Subaru Se-
lect Monitor. <Ref. to 4AT(diag)-16, CLEAR MEM-
ORY MODE, OPERATION,
Monitor.>
5) Using the Subaru Select Monitor, check that
there is no DTC displayed.<Ref. to 4AT(diag)-14,
READ DIAGNOSTIC TROUBLE CODE (DTC),
OPERATION, Subaru Select Monitor.>
6) Warm-up the engine until the ATF temperature
displayed on the Subaru Select Monitor reaches 60
— 90°C (140 — 194°F). <Ref. to 4AT(diag)-15,
READ CURRENT DATA, OPERATION, Subaru
Select Monitor.>
7) Shift the select lever to "R" range.
8) Turn all switches including headlight, air condi-
tioner, seat heater, rear defogger and etc. OFF.
9) Wait for 30 seconds or more with the ignition key
turned to OFF.
10) When "Communication Failed!" is displayed on
Subaru Select Monitor, press the brake pedal fully
until the learning control promotion is completed.
11) Turn the ignition switch to ON.
12) Change Subaru Select Monitor to «Transmis-
sion Diagnosis» display screen.<Ref. to 4AT(diag)-
14, OPERATION, Subaru Select Monitor.>
13) Check that the Subaru Select Monitor is re-
turned to normal operation.
Subaru Select Monitor
14) Shift the select lever to "P" range, and then wait
for more than 3 seconds.
15) Shift the select lever to "R" range, and then wait
for more than 3 seconds.
16) Shift the select lever to "N" range, and then wait
for more than 3 seconds.
17) Shift the select lever to "D" range, and then wait
for more than 3 seconds.
18) Shift the select lever to "N" range, and then wait
for more than 3 seconds.
19) Slowly depress the accelerator pedal to full
throttle.
20) Slowly release the accelerator pedal complete-
ly.
21) Start the engine, and idle it.
22) Shift the select lever to "D" range.
23) Start learning control promotion. At this time,
the SPORT indicator light in the combination meter
will start blinking at 2 Hz. When the SPORT indica-
tor light does not blink, turn the ignition switch to
OFF and repeat the procedures from step 4). When
the SPORT indicator light blinking at 2 Hz goes
OFF, facilitation of learning control is completed.
NOTE:
When blinking of SPORT indicator light changes
from 2 Hz to 4 Hz during learning control promo-
tion, repeat the procedure from step 4).
24) Shift the select lever to "N" range, and then turn
the ignition switch to OFF.
25) Shift the select lever to "P" range to complete
Subaru Select
the learning control promotion.
4AT(diag)-16