Subaru LEGACY 2006 Manual page 3345

asieps_tobira.book 51 ページ ２００９年１０月２６日 月曜日 午前９時１６分
3) Install the control valve body.
Tightening torque:
8 N·m (0.8 kgf-m, 5.8 ft-lb)
NOTE:
Be careful not to catch harness in.
(1)
(2)
(1)
(2)
(2)
(2)
(2)
(1) 58 mm (2.28 in)
(2) 65 mm (2.56 in)
4) Connect the control valve connector and front
vehicle speed sensor connector.
(A)
(A) Control valve connector
(B) Front vehicle speed sensor connector
5) Apply proper amount of liquid gasket to the en-
tire oil pan mating surface.
Liquid gasket:
THREE BOND 1217B (Part No. K0877YA020)
6) Install the oil pan by equally tightening the bolts.
Tightening torque:
5 N·m (0.5 kgf-m, 3.7 ft-lb)
Rear Vehicle Speed Sensor
7) Install the rear vehicle speed sensor and turbine
speed sensor 1, and then fasten the harness.
Tightening torque:
8) Install a new aluminum washer and oil cooler
pipe.
(1)
Tightening torque:
(1)
(1)
9) Install the oil charge pipe. <Ref. to 5AT-62, IN-
STALLATION, Oil Charge Pipe.>
(1)
10) Install the transmission rear crossmember bolt.
(1)
Tightening torque:
(1)
11) Install the propeller shaft. <Ref. to DS-11, IN-
AT-01958
STALLATION, Propeller Shaft.>
12) Install the heat shield cover.
13) Install the center, rear exhaust pipes and the
muffler. (Turbo model)
<Ref. to EX(H4DOTC)-9, INSTALLATION, Center
Exhaust Pipe.> <Ref. to EX(H4DOTC)-12, IN-
STALLATION, Rear Exhaust Pipe.> <Ref. to
EX(H4DOTC)-13, INSTALLATION, Muffler.>
14) Install the rear exhaust pipe and muffler. (Non-
turbo model) <Ref. to EX(H6DO)-7, INSTALLA-
(B) TION, Rear Exhaust Pipe.> <Ref. to EX(H6DO)-9,
INSTALLATION, Muffler.>
15) Lower the vehicle.
16) Install the transmission connector to the stay,
and then connect the connector.
17) Install the intercooler. (Turbo model)<Ref. to
IN(H4DOTC)-12, INSTALLATION, Intercooler.>
AT-01956
18) Install the air intake chamber. (Non-turbo mod-
el) <Ref. to IN(H6DO)-7, INSTALLATION, Air In-
take Chamber.>
19) Pour ATF from the oil charge pipe. <Ref. to
5AT-26, REPLACEMENT, Automatic Transmis-
sion Fluid.>
20) Check the level and leaks of ATF. <Ref. to 5AT-
26, INSPECTION, Automatic Transmission Fluid.>
21) Execute the learning control promotion. <Ref.
to 5AT(diag)-22, PROCEDURE, Learning Con-
trol.>
AT-03249
5AT-51
AUTOMATIC TRANSMISSION
7 N·m (0.7 kgf-m, 5.2 ft-lb)
40 N·m (4.1 kgf-m, 29.51 ft-lb) (ATF inlet pipe)
45 N·m (4.6 kgf-m, 33.2 ft-lb) (ATF outlet pipe)
70 N·m (7.1 kgf-m, 51.6 ft-lb)