NXP Semiconductors PN7462 series User Manual page 180

NXP Semiconductors
Bit Symbol
INTERNAL_USE [1]
15
INTERNAL_USE [1]
14:13
INTERNAL_USE [1]
12
INTERNAL_USE [1]
11
INTERNAL_USE [1]
10
INTERNAL_USE [1]
9
INTERNAL_USE [1]
8
INTERNAL_USE [1]
7
INTERNAL_USE [1]
6
TX_ALM_TYPE_SELECT
5
INTERNAL_USE [1]
4
TX_ALM_ENABLE
3
INTERNAL_USE [1]
2
INTERNAL_USE [1]
1:0
[1] Bit-field are either set by HAL or use default value from CLIF EEPROM default settings
Table 225. CLIF_RX_DATA_BUFFER_REG register (address 00ECh)
* = reset value
Bit Symbol
31:0 RX_DATA_BUFFER
Table 226. CLIF_TEST_CONTROL_REG register (address 00FCh)
* = reset value
Bit Symbol
[1]
31 INTERNAL_USE
[1]
30 INTERNAL_USE
[1]
29 INTERNAL_USE
[1]
28:27 INTERNAL_USE
[1]
26 INTERNAL_USE
[1]
25 INTERNAL_USE
[1]
24 INTERNAL_USE
[1]
23 INTERNAL_USE
22:21 TADT_EXTEND_SE
LECT
20 PRBS_TYPE
19 LONG_LD_MASK_E
NABLE
[1]
18 INTERNAL_USE
UM10858
User manual
COMPANY PUBLIC
Access Value
R 0
R/W 0*, 3
R/W 0*, 1
R 0
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
R 0
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
R/W 0* - 3h
Access Value
0h-FFFFFFFFh Data buffer for APB based Buffer Manager data transfer.
R
Access Value
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
R 0
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
R/W 0*, 3
R/W 0*, 1
R/W 0*, 1
R/W 0*, 1
All information provided in this document is subject to legal disclaimers.
Rev. 1.4 — 14 May 2018
314514
PN7462 family HW user manual
Description
For internal use
For internal use
For internal use
For internal use
For internal use
For internal use
For internal use
For internal use
For internal use
Defines which ALM type is used. If set to 1 Dual-Loop-ALM
is used, default (0) is Single-Loop-ALM.
Selects the driver to be used for ALM.
For internal use
If set to 1 ALM is used for transmission in card mode
For internal use
For internal use
Description
Description
For internal use
For internal use
For internal use
For internal use
For internal use
For internal use
For internal use
For internal use
By setting a value != 0 the minimum time for T
be increased
Defines the PRBS type; If set to 1, PRBS15 is
selected, default value 0 selects PRBS9
If set to 1, the masking time for the NFC-LD after
TxRFOff is longer.
For internal use
UM10858
can
ADT
© NXP B.V. 2018. All rights reserved.
180 of 345