Table of Contents
Advertisement
DADF Side Edge Registration Check - Side 2
1.
Place the Cross Line Test Pattern on the DADF with the word TOP Face Down and
towards the rear of the DADF.
2.
Select the following:
•
Tray 1
•
2-2 Sided.
•
100%
•
1 copy
3.
Make one copy to the center tray.
4.
Remove the copy from the center tray but DO NOT FLIP the copy this time.
5.
Fold the copy in half parallel to the short edge (A to B in
6.
Check that the fold line is within 2.0mm from the reference line. If the value is not within
the specified range, perform the Side 2 Adjustment.
Adjustment
Side 1 Adjustment
NOTE: In order for the following NVM changes to take effect, you must exit diagnostics and
switch the power off, then on.
1.
Enter NVM Read/Write. Change the value in location 711-272 to perform correction for all
sizes. Change the value in the locations listed in
cific size.
Table 1 Side 1
NVM
Document Width
Document Size
1
711-272
For all sizes
For all sizes
2
715-056
139.7~148.0mm
A5 SEF, 5.5x8.5" SEF
3
715-058
182.0~194.0mm
B5 SEF, 16K SEF
4
715-060
203.2mm
8x10" SEF, 8x10.5" SEF
5
715-062
210mm
A4 SEF, A5 LEF
6
715-064
214.9~215.9mm
Letter SEF, Legal SEF, 5.5x8.5" LEF, 8.46x12.4" SEF,
8.5x13" SEF
7
715-066
254.0~257.0mm
B4 SEF, B5 LEF, 8x10" LEF
8
715-068
266.7~267.0mm
16K LEF, 8K LEF, 8x10.5" LEF
9
715-070
279.4mm
Letter LEF, 11x15" SEF, 11x17" SEF
10
715-072
297mm
A4 LEF, A3 SEF
2.
Increase the value to move the image toward "TOP." Each bit represents 0.1% change.
3.
Repeat Check and Adjustment until the measurement is within the specified range.
Repairs & Adjustments
ADJ 5.2
Figure
1).
Table 1
to perform correction for a spe-
07/2011
4-192
BUS Updated 12/2011
Side 2 Adjustment
1.
Enter NVM Read/Write. Change the value in location 711-274 to perform correction for all
sizes. Change the value in the locations listed in
cific size.
Table 2 Side 2 of 2 Sided mode
NVM
Document Width
Document Size
1
771-274
For all sizes
For all sizes
2
715-057
139.7~148.0mm
A5 SEF, 5.5x8.5" SEF
3
715-059
182.0~194.0mm
B5 SEF, 16K SEF
4
715-061
203.2mm
8x10" SEF, 8x10.5" SEF
5
715-063
210mm
A4 SEF, A5 LEF
6
715-065
214.9~215.9mm
Letter SEF, Legal SEF, 5.5x8.5" LEF, 8.46x12.4" SEF,
8.5x13" SEF
7
715-067
254.0~257.0mm
B4 SEF, B5 LEF, 8x10" LEF
8
715-069
266.7~267.0mm
16K LEF, 8K LEF, 8x10.5" LEF
9
715-071
279.4mm
Letter LEF, 11x15" SEF, 11x17" SEF
10
715-073
297mm
A4 LEF, A3 SEF
2.
Repeat the Check and Adjustment until the measurement is within the specified range.
NOTE: The Values of NVM 711-272 and 711-274 are written to NVM's 715-110, 715-111, 715-
112, and 715-113, when the machine power is switched on.
•
711-272 written to 715-110
•
711-274 written to 715-111, 715-112, 715-113
Table 2
to perform correction for a spe-
Initial Issue
WorkCentre 5335 Family Service Documentation
Advertisement
Table of Contents
