Output Component Control Codes - Office Finisher Lx - Xerox workcentre 5335 series Service Manual

Chain-
Link Component
012-013 Sub Paddle Solenoid
012-018 Transport Motor Reverse
012-020 Front Tamper Mot Low Front
012-022 Front Tamper Mot High Front
012-023 Front Tamper Mot Low Rear
012-025 Front Tamper Mot High Rear
012-026 Rear Tamper Motor Low Front Rear Tamper moves to Front at low speed.
012-028 Rear Tamper Motor High Front Rear Tamper moves to Front at high speed.
012-029 Rear Tamper Motor Low Rear Rear Tamper moves to Rear at low speed.
012-031 Rear Tamper Motor High Rear Rear Tamper moves to Rear at high speed.
012-032 H-Transport Motor 1
012-033 H-Transport Motor 2
012-034 H-Transport Motor 3
012-035 H-Transport Motor 4
012-036 Transport Motor 1
012-037 Transport Motor 2
012-038 Transport Motor 3
012-039 H-Transport Motor Reverse
012-040 Stapler Move Motor Front Low Stapler Assy moves to Front at low speed
012-042 Stapler Move Motor Front High Stapler Assy moves to Front at high speed
012-043 Stapler Move Motor Rear Low Stapler Assy moves to Rear at low speed
012-045 Stapler Move Motor Rear High Stapler Assy moves to Rear at high speed
012-046 Staple Motor Forward
012-047 Staple Motor Reverse
012-051 Set Clamp Paddle
012-052 Eject Clamp Up
012-053 Eject Clamp Down
012-054 Eject Motor Forward Low
012-055 Eject Motor Forward High
012-060 Stacker Motor Up
012-061 Stacker Motor Down
012-074 Punch Motor Move Home
012-077 Punch (2 hole)
General Procedures & Information
Component Control
Table 6 Output Component Control Codes - Office Finisher LX
Description
Transport Motor reverse rotation
Front Tamper moves to Front at low speed.
Front Tamper moves to Front at high speed.
Front Tamper moves to Rear at low speed.
Front Tamper moves to Rear at high speed.
Xport Motor normal rotation at speed 1 (highest speed)
Xport Motor normal rotation at speed 2 (high speed)
Xport Motor normal rotation at speed 3 (medium speed)
Xport Motor normal rotation at speed 4 (low speed)
Transport Motor normal rotation at speed 1 (high speed)
Transport Motor normal rotation at speed 2 (med speed)
Transport Motor normal rotation at speed 3 (low speed)
H-Transport Motor reverse rotation
Stapling operation is performed.
Staple motor reverses.
Rotate Set Clamp Paddle one time (both Set Clamp Paddle Clutch and Eject Motor Forward)
turned on at the same time
Eject Clamp Roll moving up. Eject Motor reverse rotation at high speed.
Eject Clamp Roll moving down. Eject Motor reverse rotation at high speed.
Eject Motor rotates forward at low speed
Eject Motor rotates forward at High speed
Stacker Tray goes up.
Stacker Tray goes down.
Punch motor home positioning
2-hole punch movement
BUS Updated 12/2011
07/2011
6-26
Time-out conflicts
250 ms
012-036, 012-037, 012-038
82 pulses 012-022, 012-023, 012-025
82 pulses 012-020, 012-023, 012-025
82 pulses 012-020, 012-022, 012-025
82 pulses 012-020, 012-022, 012-023 012-024
82 pulses 012-027, 012-028, 012-029, 012-031
82 pulses 012-026, 012-029, 012-031
82 pulses 012-026, 012-028, 012-031
82 pulses 012-026, 012-028, 012-029, 012-031
012-033, 012-034, 012-035, 012-039
012-032, 012-034, 012-305, 012-039
012-032, 012-033, 012-035, 012-039
012-032, 012-033, 012-034, 012-039
012-018, 012-037, 012-038
012-018, 012-036, 012-038
012-018, 012-036, 012-037
012-032, 012-033, 012-034, 012-035
012-042, 012-043, 012-045
012-040, 012-043, 012-045
012-040, 012-042, 012-045
012-040, 012-042, 012-043
012-047
200ms 012-046
583 pulses 012-086
702 pulses 012-053, 012-054, 012-055
after Home
46 pulses 012-052, 012-054, 012-055
after Home
1136 pulses 012-052, 012-053, 012-055
1136 pulses 012-052, 012-053, 012-054
500ms 012-061
500ms 012-060
when Home 012-077, 012-078, 012-079
reached
when Home 012-074, 012-078, 012-079
reached
Initial Issue
WorkCentre 5335 Family Service Documentation