Fujitsu MB90460 Series Hardware Manual page 734

ROM Correction
Block Diagram of ROM Correction Function
.......................................................... 573
Operation of the ROM Correction Function........ 578
ROM Correction Function Registers .................. 574
ROM Correction Interrupts ............................... 572
ROM Mirroring Function Selection Module
ROM Mirroring Function Selection Module Block
Diagram ............................................. 584
ROM Mirroring Function Selection Module Register
.......................................................... 584
ROM Mirroring Function Selection Register
ROM Mirroring Function Selection Register
(ROMM)............................................ 585
ROMM
ROM Mirroring Function Selection Register
(ROMM)............................................ 585
RP
Register Bank Pointer (RP) ................................. 50
RTO
Output Condition of RTO0 to RTO5 and GATE
.......................................................... 339
RUN Mode
RUN Mode...................................................... 158
S
Sample
Sample I/O Port Program .................................. 203
Sample Program
Processing Specifications of Sample Program for
Extended Intelligent I/O Service (EI
.......................................................... 153
Sample Program for 16-bit Free-run Timer ......... 351
Sample Program for 16-bit Output Compare ....... 352
Sample Program for Continuous Conversion Mode
2
OS ....................................... 566
using EI
Sample Program for Single Conversion Mode using
2
EI OS ................................................ 564
Sample Program for Stop Conversion Mode using
2
EI OS ................................................ 568
Sample Program for the 16-bit PPG Timer ......... 277
Sample Program for the DTP Function............... 533
Sample Program for the External Interrupt Function
.......................................................... 532
Sample Program for the Multi-pulse Generator
.......................................................... 431
Sample Program for the PWC Timer.................. 464
Sample Program for the Time-base Timer .......... 216
Sample Program for the Watchdog Timer........... 227
Sample Program for UART............................... 510
Sample Program in Event Count Mode .............. 254
Sample Program in Internal Clock Mode ............ 253
Sample Programs
Sample Programs for Interrupt Processing .......... 152
SCR
Serial Control Register (SCR0/SCR1) ................476
Sector
Procedure of Deleting a Sector...........................605
Restarting the Sector Deletion............................608
Sector Configuration .........................................589
Temporarily Stopping the Sector Deletion...........607
When the Sector Deletion Temporary Stop is
Sector Deletion
Restarting the Sector Deletion............................608
Temporarily Stopping the Sector Deletion...........607
When the Sector Deletion Temporary Stop is
Sector deletion
Deleting the data (Sector deletion)......................605
Sector Deletion Operation
When the Chip/Sector Deletion Operation is Executed.
When the Sector Deletion Operation is Executed.
When the Write Operation or Chip/Sector Deletion
Sectors
Notes on Specifying Two or More Sectors ..........605
Serial Control Register
Serial Control Register (SCR0/SCR1) ................476
Serial Mode
Serial Mode Register (SMR0/SMR1) .................478
Serial Mode Register
Serial Mode Register (SMR0/SMR1) .................478
2
OS)
Serial On-board Writing
Standard Configuration for Fujitsu Standard Serial
Serial Status Register
Serial Status Register (SSR0/SSR1) ...................480
Serial Writing
Example of Connection for Serial Writing (when
Example of Connection for Serial Writing (when
SIDR
Input Data Register (SIDR0/SIDR1)...................482
SIGCR
Waveform Control Register (SIGCR) .................318
Signal Flow Diagram
Signal Flow Diagram for OPDBR0 by Setting OPS2 to
Signal Flow Diagram for Position Detection by Setting
Signal Flow Diagram for Reload Timer 0 and Position
Executed. ....................................595, 597
Executed. ....................................595, 597
..........................................................595
..........................................................599
Operation is Executed. .................597, 598
On-board Writing ................................616
Power Supplied by User) ......................618
Power Supplied from Writer) ................620
OPS0=000 .............................................401
B
OPS2 to OPS0=010 or 110
B
Detection by Setting OPS2 to OPS0 = 011
or 111 ....................................................403
B
INDEX
.................403
B
B
715