Subaru LEGACY 2006 Manual page 4107

asieps_tobira.book 9 ページ ２００９年１０月２６日 月曜日 午前９時１６分
2. DATA DISPLAY
1) On the «Main Menu» display screen, select {Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display screen, select the {Tire Pressure Monitor} and press the [YES]
key.
3) Press the [YES] key after the {Tire Pressure Monitor} is displayed.
4) On the «Tire pressure monitor diagnosis» display screen, select the {Data Display}, and then press the
[YES] key, then necessary data will be displayed.
• A list of the support data is shown in the following table.
1. Data monitor (Analog)
Display
FR FN Code
FL FN Code
RR FN Code
LEARN, LOW BAT, OFF, WAKE, RE ME, NOR-
MAL
RL FN Code
FR tire pressure
Value converted to tire pressure from data deliv-
FL tire pressure
ered from transmitter is displayed.
(The figure may differ from the actual measured
RR tire pressure
values.)
RL tire pressure
Vehicle speed signal which is input in control mod-
Vehicle Speed
ule.
Pressure warning Threshold where tire pressure warning light lights
Threshold where tire pressure warning light goes
Return pressure
out
3. CLEAR MEMORY
1) On the «Main Menu» screen, select {2. Each
System Check} and press the [YES] key.
2) On the «System Selection Menu» display
screen, select the {Tire Pressure Monitor} and
press the [YES] key.
3) Press the [YES] key after the {Tire Pressure
Monitor} is displayed.
4) On the «Tire Pressure Monitor Diagnosis» dis-
play screen, select the {Clear Memory} and press
the [YES] key.
5) When "Done" and "Turn ignition switch OFF" is
shown on the display screen, turn the Subaru Se-
lect Monitor and ignition switch OFF.
NOTE:
For details concerning the operation procedures,
refer to the "SUBARU SELECT MONITOR OPER-
ATION MANUAL".
Subaru Select Monitor
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS)
Contents to be monitored
TPM(diag)-9
Unit of measure
LEARN: Transmitted transmitter ID using the transmit-
ter registration tool
LOW BAT: Transmitter battery voltage running low
OFF: Transmitter function stops (no data transmission)
RE ME: Tire air changes ±8.4 kPa
WAKE: When data transmission is started from a
stopped state.
NORMAL: Conditions other than above
kPa, psig, mmHg, inHg
kPa, psig, mmHg, inHg
kPa, psig, mmHg, inHg
kPa, psig, mmHg, inHg
km/h, MPH
kPa, psig, mmHg, inHg
kPa, psig, mmHg, inHg
4. REGISTER TRANSMITTER ID
Perform the procedures below to register the trans-
mitter.
• Transmitter replaced.
• Switched the position of the transmitter (rotated
tires)
• Replaced the tire pressure monitoring control
module.
NOTE:
• If registration of the transmitter ID is not possible
after 2 attempts, replace the tire pressure monitor-
ing control module. <Ref. to WT-11, TIRE PRES-
SURE MONITORING CONTROL
REMOVAL, Tire Pressure Monitoring System.>
<Ref. to WT-12, TIRE PRESSURE MONITORING
CONTROL MODULE, INSTALLATION, Tire Pres-
sure Monitoring System.>
• If the ignition switch and Subaru Select Monitor
power are turned OFF while registering the trans-
mitter, or if registration is not possible for more than
5 minutes, the registration mode is cancelled.
• When rotating tires, there is no affect on the per-
formance or functions of the tire pressure monitor-
ing control module even if the transmitter (ID) is not
registered, however, the tire position displayed on
the Subaru Select Monitor will be incorrect.
MODULE,