MCi iControl User Manual page 738

Speed Reference
Following error 9-90
Speed reference frequency parameter 9-91
Speed Reference parameters 9-89, 9-90
Speed reference resolution parameter 9-89
Speed reference rotational direction parameter 9-89
Speed reference scaling parameter 9-89
Speed reference type parameter 9-89
Speed Reference, setting 2-56
speed variance, up vs. down 2-57
Split Bank 10-29
Activation 10-29
Deactivation 10-29
Hall call eligibility 10-30
Hall Risers 10-30
Riser connections 10-58
Standard profile 4-13, 9-128
Status display, iBox LEDs 7-11
Status messages on the iBox LCD display 7-12
Stuck Car Panel Inspection Input message 6-74
Stuck Cartop Inspection Input message 6-74
STUCK CP INSP. INPUT message 6-74
STUCK CT INSP. INPUT message 6-74
STUCK IN. INPUT FLT message 6-74
Stuck Inspection Input Fault message 6-74
Sub-address jumper 5-34
Subnet Mask 2-34, 7-9, 8-4
Sufficient Field Status test point, description 11-6
Support availability 1-3
Swing Automatic Operation input 9-109
Swing car, description of 10-4
Swing Dispatching 10-6–??
Swing operation
Enable 9-39
parameters 9-39
Swing Operation Activated message 6-74
Swing Operation Deactivated message 6-74
Swing Operation Indicator output 9-119
Swing Operation message 6-74
Swing Operation Switch input 9-109
Switching between PCs 5-2
Switching the monitor 5-2
Symbols 2-8
Synthetic Signal test point, description 11-6
Sys Comm, iBox status LED 7-11
System 12 SCR Drive
auto offset calibration 2-48
initial settings 2-48
System Configurations (Simplex) inputs 9-112
System Configurations (Simplex) outputs 9-123
System Control Switches 1-7
System control switches on the iBox 7-12
System Event Log 10-68
open saved file 10-68
save to file 10-68
System Event log, view details 10-68
System I/O
Input inventory 10-61
Output inventory 10-61
System I/O configuration 10-51
Index-20 Manual # 42-02-2222
System I/O Troubleshooting 5-36
System monitoring 1-1
System Options 5-1–5-52
MCE Load Weigher 5-63–5-69
Serial COP 5-48–5-52
Serial Hall Calls 5-30–??
System Performance 10-74
System Status Display 1-7
System status, Fault bypass 9-18
SYSTEM SYNC message 6-73, 6-74
System TCP/IP 5-11
System User Outputs 9-124
System View 9-1
System view 10-2
T
Tach Error Fault message 6-74
Tach Error Lower Limit test point, description 11-6
Tach Error tripping threshold adjustment 4-41
Tach Error Upper Limit test point, description 11-6
Tach Failure, TACH FAILURE message 6-74
Tachometer iBox Connections 6-112, 11-7
Tachometer Signal test point, description 11-6
TB, Brake Triac active indicator 11-12
TC, Tach Signal input 6-112, 11-7
TCP/IP 5-11, 5-14, 5-35
TCP/IP Addresses 2-5, 2-30, 2-34, 5-15, 5-18, 8-4
setting in iView 9-125
setting on the iBox 7-9
TCP/IP cables 5-12
Temporary Cartop Wiring 2-29
Temporary CTS Relay Bypass 2-28
TERMINAL LEARN ON message 6-75
Terminal Learn procedure 9-151
Terminal switches configuration 9-134
Terminal switches status 9-19
TERMINAL SYNC FAULT message 6-75
Terminal synchronization 4-3, 9-130
Terminal Synchronization Fault message 6-75
Terminals, input and output wiring 2-13
Test mode 9-7
Test Mode message or Test message 6-75
Test Mode output 9-120
Test point signal descriptions 11-3–11-6
Test switch, iBox control 7-12
THIS CAR ALT FIRE message 6-75
This Car Alternate Fire Sensor Recall message 6-75
This Car Alternate input 9-109
THIS CAR MAIN FIRE message 6-75
This Car Main Fire Sensor Recall message 6-75
This Car Main input 9-110
Time, setting 8-38
Timer tables
configuration 10-62
configuring 9-135
examples 9-137, 10-64
programming 9-135, 10-62
TM, Motor Triac active indicator 11-12
Toggle Output 9-124