MCi iControl User Manual page 733

MDRD, Motor Drive Redundancy indicator 11-12
Mechanical Safe Edge 9-30
Mechanically In Service output 9-119
Melina PI display Outputs 9-122
Menu tree, iBox LCD display 7-6
MF FORCING TIMED OUT message 6-55
MF1, MF2, DC power to motor field 11-14
Minimum Floor to Floor Time specification 11-2
Mode of Operation 5-26, 9-5, 10-14
Mode of Operation Config inputs 9-112
Mode of Operation Config outputs 9-123
monitoring Diagnostic Outputs 9-13
Motion
Actual direction 9-9
Category 9-9
Commanded direction 9-9
Motion Start Fault message 6-55
Motion stopped due to IO toggle test message 6-55
MOTION STOPPED-IO TST message 6-55
Motion, diagnostic flags 9-12
Motor blower hold delay parameter 9-88
Motor Blower output 9-122
MOTOR CNTR PROOF FLT message 6-55
Motor Contactor Driver Proofing Fault message 6-55
Motor Contactor Proofing Fault message 6-55
Motor Contactor Status test point, description 11-5
Motor Current Limiting 4-14
Motor Field Forcing Timed Out message 6-55
Motor insulation 2-21
Motor Limit Protection Timer Elapsed message 6-55
MOTOR LIMIT TIMED OUT message 6-55
Motor Limit Timed Out message 6-55
MOTOR LMT TIMED OUT 2 message 6-55
Motor Noise 4-15
Motor Overload Protection, verifying 2-60
Motor Triac active indicator 11-12
MOTR CNTR DRV PRF FLT message 6-55
Move idle car penalty 10-11
Move lobby parked car penalty 10-11
Move non-lobby parked car penalty 10-11
MR HEAT DETECTORS message 6-54
MR INSP. DISABLED message 6-54
MR STOP SWITCH OPEN message 6-54
MRD, Motor Redundancy indicator 11-12
Multiple Input AC Board Quick Reference 6-104
Multiple Output Relay Board Quick Reference 6-107
N
Network Info 5-26
Node Control 5-26
Non-interference timer 9-30
Non-lobby parking delay 10-21
Non-lobby shuffle delay 10-21
Non-peak hall call assignment penalty 10-17
Normal and Emergency Terminal Switch Position Tests 4-54
Normal rate limited stop parameter 9-89
Normal rate limited stop, adjusting for final stop 4-26
Normal Terminal Slowdown Limit (NTS) 4-9
Normal Terminal Switch Overspeed Tests 4-53
Nudging 9-37
Nudging Front, NUDGING FRONT message 6-56
Nudging Operation message 6-56
Nudging Rear, NUDGING REAR message 6-56
Number of Cars in Group specification 11-2
Number of Stops specification 11-2
O
OK Write Privileges 1-13
Online help, accessing 8-24
Operational Status tab 9-8
Orange cables 5-12, 5-35
Oscilloscope
editing displays 8-39, 9-22
Enable/Disable Tracking 9-22
Scale 9-23
Zoom to Fit 9-23
OTHER CARS ALT FIRE message 6-56
Other Cars Alternate Fire Sensor Recall message 6-56
Other Cars Alternate input 9-109
OTHER CARS MAIN FIRE message 6-56
Other Cars Main Fire Sensor Recall message 6-56
Other Cars Main input 9-109
Outputs, programming 9-115
Over Current Power Threshold test point, description 11-5
Over Current test point, description 11-5
Over Current Threshold test point, description 11-5
Over Load Input 9-109
Over Load Threshold 9-127
Overload output 9-119
Overload threshold 4-31, 4-32
Overloaded car detection 4-30
Overshoot correction, Contract speed runs 4-14
Overshoot, adjusting for 4-8
Overspeed 1 9-20
description of 4-55
Overspeed 1 margin, Safety parameter 9-148
Overspeed 2 9-20
description of 4-55
P
PARAM CHNG-RESET CAR message 6-41
Parameter adjustment
using iView 8-18
using the iBox 7-5
Parameter entry screens 1-13, 8-18
parameter settings, verifying initial 2-43
Parameters, Load from Configuration file 8-22
Parameters, Save to File 8-20
Parking 10-20
Parking Config inputs 9-112
Parking Config outputs 9-123
Parking Configurations 10-21
Parking Delay Timers 10-21
Parking Eligibility 10-27
Parking Eligibility Config inputs 9-112
Parking Eligibility Config outputs 9-123
Partial pick voltage 9-25
Pass Code Failure output 9-119
Pass Code Success output 9-119
Index-15