MCi iControl User Manual page 721

current, on Operational Status tab 9-10
Filters 9-25
iBox connections 11-12
Output Timer 9-27
Resistance 2-22
setup 9-140
Timers 9-26
verify picking 2-53
Voltage 6-16
voltage, on Operational Status tab 9-10
voltages 9-25, 9-27
wiring 2-23
BRAKE CNT DRV PRF FLT message 6-14
BRAKE CONT PRF FAULT message 6-15
Brake Contactor Driver Proofing Fault message 6-14
Brake Contactor Proofing Fault message 6-15
Brake Contactor Status test point, description 11-4
Brake coordination, adjusting for smooth stops 4-28
Brake Current Feedback test point, description 11-4
Brake current low pass frequency parameter 9-25
Brake Current Resistance 2-22
Brake Current Signal test point, description 11-4
Brake Drive Redundancy indicator 11-12
Brake drop delay 9-26
Brake drop delay, adjusting for final stop 4-26
BRAKE DROP FAULT message 6-15
Brake Drop Fault message 6-15
Brake Enable Fault message 6-15
Brake Enable Status test point, description 11-4
Brake Holding Voltage output 9-122
Brake IGBT Fault, see Excessive Brake Feedback Fault mes-
sage 6-34
Brake Module Over Temperature Fault message 6-15
Brake Output Circuit Failure message 6-16
BRAKE OUTPUT FAILURE message 6-16
BRAKE OVER TEMP FAULT message 6-15
Brake pick delay 9-26
adjusting 3-31
BRAKE PICK FAULT message 6-16
Brake Pick Fault message 6-16
Brake Pick Fault Off message 6-16
Brake release time, adjusting for final stop 4-26
Brake Switch input 3-20, 9-112
Brake Triac active indicator 11-12
BRAKE V NOT ON FAULT message 6-16
Brake Voltage Feedback test point, description 11-4
Brake voltage low pass frequency parameter 9-25
Brake Voltage Not On Fault message 6-16
Brake Voltage Signal test point, description 11-4
BRD, Brake Redundancy indicator 11-12
Bus 2 Fuse Open message 6-16
Bus 2D Fuse Open message 6-16
Bus 2MC Fuse Open message 6-17
Bus 2PI Fuse Open message 6-17
Bus 3 Fuse Open message 6-17
Bus 3HA Fuse Open message 6-17
Bus Enabled 5-26
Bus Status 5-26
Bus Voltage 5-26
Bypass Jumper, using for troubleshooting 6-3
Bypass status, Fault bypass 9-18
Bypass Timers
Photo Eye 9-31
Safe Edge 9-30
C
Cabinet Installation 2-9
cables for Velocity Encoder 2-26
Calibrate Floor offsets 4-23
Cancel car calls behind car 9-38
Cancel In-Car CFSS Mode 1 input 9-106
Cancel In-Car CFSS Mode 2 input 9-106
Cancel remaining car calls with direction reversal 9-38
Capture Input 9-106
Capture Input OFF message 6-17
Capture Input ON message 6-17
Capture message 6-17
Capture mode 9-5
Capture Mode message 6-17
Capture Mode switch, iBox control 7-12
Car at same floor bonus 10-11
Car Call Audible output 9-115
Car Call Cancel Button input 9-106
Car Call Dwell Time 9-41
Car Call Enable 1 - Front inputs 9-112
Car Call Enable 1 - Rear inputs 9-112
Car Call Enable 2 - Front inputs 9-112
Car Call Enable 2 - Rear inputs 9-112
Car call enable floor passcodes 10-48
Car Call Enable Operation 1 (2) Override input 9-106
Car call enable passenger passcodes 10-49
Car Call Registered Audible output 9-115
Car Call Restrictions - elevator security 10-45
Car Call Security 1 (2) Override outputs 9-115
Car calls 10-73
Car Calls - Front COP 1 outputs 9-121
Car Calls - Front COP 2 outputs 9-121
Car Calls - Front COP1 inputs 9-111
Car Calls - Front COP2 inputs 9-111
Car Calls - Rear COP 1 outputs 9-121
Car Calls - Rear COP 2 outputs 9-121
Car Calls - Rear COP1 inputs 9-111
Car Connections, iBox 6-113, 11-8
CAR DEL DOORS CLOSED message 6-17
CAR DEL DOORS CLOSING message 6-17
CAR DEL DOORS OPEN message 6-18
CAR DEL DOORS OPENING message 6-18
CAR DEL DOORS STALLED message 6-18
CAR DEL DOORS UNKNOWN message 6-18
Car Delayed output 9-116
Car delayed timer 9-38
Car delayed with doors closed message 6-17
Car delayed with doors closing message 6-17
Car delayed with doors open message 6-18
Car delayed with doors opening message 6-18
Car delayed with doors stalled message 6-18
Car delayed with unknown door position message 6-18
car direction, verifying 2-55
car does not reach high speed 4-11
Car Door Bypass message 6-18
Index-3