MCi iControl User Manual page 723

CFSS Car Light 1 (2) outputs 9-116
CFSS In Car Switch 1 input 9-107
CFSS In Car Switch 2 input 9-107
CFSS In Use 1 (2) outputs 9-123
CFSS Mode 1 (2) at Floor mode 9-5
CFSS Mode 1 (2) In-car mode 9-5
CFSS Mode 1 (2) In-Use outputs 9-116
CFSS Mode 1 (2) Recall mode 9-5
CFSS Mode 1 (2) System outputs 9-116
CFSS Mode 1 at Floor Activated message 6-22
CFSS Mode 1 In-car Activated message 6-23
CFSS Mode 1 Recall Activated message 6-23
CFSS Mode 2 at Floor Activated message 6-23
CFSS Mode 2 In-car Activated message 6-23
CFSS Mode 2 Recall Activated message 6-23
CFSS operation 10-9
CFSS Recall 9-74
In-car audible indicator 9-74
In-car visual indicator 9-74
CFSS serial outputs 10-53
CFSS System 1 (2) outputs 9-123
CFSS tab 10-9
Changing parameters 2-30
Check for shorts to ground 2-16
Checking AC phase 5-7
Checking the Hoist Motor 2-21
Circuit board removing & replacing 6-79
Circuit boards, troubleshooting 6-82–6-122
CNPB Fault, see Brake Contactor Proofing Fault message 6-15
CNPBD Fault, see Brake Contactor Driver Proofing Fault
message 6-14
CNPM Fault, see Motor Contactor Proofing Fault message
6-55
CNPMB Fault, see Motor Contactor Driver Proofing Fault
message 6-55
Cnstr Car Panel Insp message 6-23
Cnstr Cartop Insp message 6-23
Cnstr CP Insp message 6-23
Cnstr CT Insp message 6-23
Cnstr HA Insp message 6-23
Cnstr HA Inspection message 6-23
Cnstr Inspection message 6-23
Cnstr Mach Room Insp message 6-23
Cnstr MR Insp message 6-23
Coincidence call bonus 10-11
Commanded direction 9-9
Commandeer For Special Service parameters 9-73–9-75, 10-9
Commercial Power output 9-116
Common Bus Connections, iBox 11-13
Computer IP address, setting 2-35–2-38, 8-6
Computer Reset, iBox control 7-4
Computer, iBox status LED 7-11
Configuration 9-24–9-137, ??–10-64
Brake 9-24
Car Call Enable 9-28
Car Operation 9-29
Drive 9-87
Floor heights 9-94
General tab 9-95
I/O Boards 9-100
Loadweigher tab 9-126
Pattern 9-128
Serial I/O 10-51
Terminal switches 9-134
Configuration File 6-80
Configuration file
creating 8-20
editing 8-23
loadding 8-22
saving 8-20
Configuration File - Generate Default 8-21
Connected 5-26
Connection Status 5-26
Connections 2-35–2-41
Direct 2-35
Construction Car Panel Inspection mode 9-5
Construction Car Panel Inspection Operation message 6-23
Construction Cartop Inspection mode 9-5
Construction Cartop Inspection Operation message 6-23
Construction Hoistway Access Inspection mode 9-6
Construction Hoistway Access Inspection Operation message
6-23
Construction Inspection mode 9-6
Construction Inspection Operation message 6-23
Construction Machine Room Inspection mode 9-6
Construction Machine Room Inspection Operation message
6-23
Construction Mode 2-1–2-60, ??–2-61, 3-1–3-25
exiting 3-25
Faults 2-3
Overview 2-2
Required connections 2-3
Contactor drop delay 9-26
Contract Overspeed Test 4-47
Contract overspeed, Safety parameter 9-148
Contract speed, Safety parameter 9-148
Controller Main Computer Startup message 6-23
Controller Specifications 11-2
Controller Stop switch, iBox control 7-12
Controller View 9-1
Controller view 9-2
COP, iLink serial connection 3-15
Correction profile 4-14, 9-128
Counterweight balancing 9-141
Counterweight balancing, preparing for final adjustments
3-29
Counterweight derailment detector 3-21
Counterweight Derailment output 9-116
counterweight learn operation 9-141
Counterweight Learn procedure 3-28
Counterweight position parameter 9-141
Coupling rotational ratio 2-45
CP INSP. DISABLED message 6-20
Creating a Configuration file 8-20
creating a direct connection 2-39
Creating a new LAN connection 8-13
Cross Registration 10-55
Cross registration serial inputs 10-55
Cross registration serial outputs 10-55
Crosshead Deflection Load Weigher 4-30
Index-5