MCi iControl User Manual page 299

Table 6.3 iControl Messages
CFSS Mode 1 In-car Activated, CFSS 1 In-car.
Description: Commandeer For Special Services is a special operating mode. When activated by a (typically)
keyed hall switch the car recalls to that floor. Two CFSS operating modes may be configured on the Car
Operations screen/CFSS tab (Mode 1, Mode 2). Typically, one of the two is used for Hospital Operation, the
second as the user determines. Once recall is activated, the car disposes of existing calls as configured on
the CFSS tab, then moves to the recall floor. At the recall floor, In-Car CFSS is activated by an in-car switch
or as configured on the CFSS tab (In-Car).
Car Reaction: As configured on the Car Operations screen/CFSS tab.
CFSS Mode 1 Recall Activated, CFSS 1 Recall. See CFSS Mode 1 In-car Activated.
CFSS Mode 2 at Floor Activated, CFSS 2 at Floor. See CFSS Mode 1 In-car Activated.
CFSS Mode 2 In-car Activated, CFSS 2 In-car. See CFSS Mode 1 In-car Activated.
CFSS Mode 2 Recall Activated, CFSS 2 Recall. See CFSS Mode 1 In-car Activated.
Construction Car Panel Inspection Operation, Cnstr Car Panel Insp, Cnstr CP Insp
Description: The car is on Construction mode and car panel inspection.
Car Reaction: Car is out of service and cannot be moved using the car panel inspection key switches.
Troubleshooting: When Construction mode is active, car panel operation switches are ignored. The car can
only be moved using Machine Room or Cartop Inspection switches. Place the car on Machine Room or Cartop
Inspection and use the appropriate switches to move the car.
Construction Cartop Inspection Operation, Cnstr Cartop Insp, Cnstr CT Insp
Description: Car is on Construction mode and Cartop Inspection. When the iBox is in construction mode, it is
always "on inspection." It will only operate in Cartop or Machine Room inspection. Car top has precedence
over Machine Room, just as in Passenger operation. If neither of these two modes of operation are selected,
the controller goes into a non-specific inspection mode. It will not run for any inspection direction input.
Car Reaction: The car can be moved using the cartop inspection key switches.
Troubleshooting:
1. If it appears that the car is on Cartop Inspection operation in error, verify wiring to the iBox INCT input.
If no voltage exists on this input, the car will operate under Cartop Inspection operation.
Construction Hoistway Access Inspection Operation, Cnstr HA Inspection, Cnstr HA Insp
Description: Car is on construction mode and hoistway access.
Car Reaction: Car is out of service and cannot be moved using the hoistway access Up or Down switches.
Troubleshooting: When Construction mode is active, hoistway access switches are ignored. The car can only
be moved using Machine Room or Cartop Inspection switches. Place the car on Machine Room or Cartop
Inspection and use the appropriate switches to move the car.
Construction Inspection Operation, Cnstr Inspection
Description: The car is operating in Inspection mode and the Construction setting on the Safety Configura-
tion screen is selected.
Car Reaction: The car will operate using the Inspection performance pattern using Cartop or machine room
inspection modes only.
Construction Machine Room Inspection Operation, Cnstr Mach Room Insp, Cnstr MR Insp
Description: Car is on inspection mode using the iBox inspection switch while on construction mode.
Car Reaction: Car begins operating in Inspection mode. If running, the car will make an emergency stop and
is taken out of normal service. Under this mode of operation, the car can be moved using the iBox Inspection
Up and Down switches.
Troubleshooting:
1. Related inputs:
MachineRoomInspection: Normally high
Controller Main Computer Startup
Description: iBox main processor booting up.
iControl Messages
iControl Messages
6-23
6