MCi iControl User Manual page 725

Down, iBox status LED 7-11
DP1-, Position Encoder input 6-112, 11-7
DP1+, Position Encoder input 6-112, 11-7
DP2-, Position Encoder input 6-112, 11-7
DP2+, Position Encoder input 6-112, 11-7
DPM, Door Position Monitor input 6-113, 11-8
Drawing Name 2-7
Drawing Number Format 2-7
Drive
Filters tab 9-91
Safety tab 9-90
Drive At Speed Fault message 6-26
Drive Calibration
calibrating offsets 9-142
Input ADC 9-93
Output DAC 9-93
Drive Communication Fault message 6-26
Drive Communication Warning message 6-26
Drive Configuration 9-87–9-93
General tab 9-88
Pre-Start Sequence parameters 9-88
Pre-Torque tab 9-92
Drive Configuration parameters 9-87–9-93
Drive Connections, iBox 11-12
Drive Control parameters 9-92
Pre-torque balance adjustment 9-92
Pre-torque gain 9-92
Pretorque position compensation 9-92
DRIVE ENABLE FDBK FLT message 6-27
Drive Enable Feedback Fault message 6-27
Drive Enable Status test point, description 11-4
DRIVE FAULT message 6-27
Drive Fault message 6-27
Drive Inspection Overspeed Fault message 6-27
Drive interface parameter 9-88
DRIVE IOS FAULT message 6-27
Drive IOS Limit test point, description 11-4
Drive IOS Param Limit test point, description 11-4
Drive Offsets calibration parameters
Input ADC 9-93
Drive On Fault message 6-27
Drive On, iBox status LED 7-11
Drive Parameters Quick Reference, TORQMAX 11-27
Drive Ready Fault message 6-28
Drive Ready On Fault message 6-27
Drive Start Failure message 6-28
Drive Type parameter 9-88
Drive, diagnostic flags 9-12
Driver VDC 5-26
DRO fault 4-19
DRO fault, empty car test 3-31
Drop delay, adjusting for final stop 4-28
Dual Channel QUAD Fault message 6-28
DUAL CHANNEL QUAD FLT message 6-28
Dynamic parking 10-21, 10-26
DZ, Door Zone Sensor input 6-113, 11-8
E
Earthquake (EQ) sensor 3-21
Earthquake board power supply OFF message 6-28
Earthquake board power supply ON message 6-28
Earthquake Board Quick Reference 6-96
Earthquake Buzzer output 9-117
Earthquake Code 9-64
Earthquake Emergency Stop message 6-28
Earthquake Light output 9-117
Earthquake Operation (Counterweight) message 6-29
Earthquake Operation (Seismic Switch) message 6-29
Earthquake Operation Activated message 6-28
Earthquake Operation Deactivated message 6-29
Earthquake parameters 9-64
Earthquake profile 4-13, 9-128
Earthquake Reduce Speed message 6-29
Earthquake reset button OK message 6-29
Earthquake reset button stuck ON message 6-29
EARTHQUAKE RUN message 6-29
Earthquake Run message 6-29
Earthquake Shutdown message 6-29
Edit a parameter on the iBox 7-5
Edit a parameter using iView 8-18
Editing a configuration file 8-23
Editing displays 8-39
EEPROM Device Error message 6-29
Egress floor 9-37
Egress Floor Gong output 9-117
Electrical Governor Test 4-46
Elevator code compliance 1-3
Elevator Recall Operation (Switch 'n') message 6-30
Elevator recall parameters 9-61
ELEVATOR RECALL SW'n' message 6-30
EM BK UIM RESET STUCK message 6-31
EMCO Load Weigher Installation 5-53
EMERG ALARM ACTIVATED message 6-30
EMERG BRAK LEG 2 SHORT message 6-31
EMERG BRAKE OK OPEN message 6-31
EMERG BRAKE TRIPPED message 6-31
EMERG BRK LEG 1 SHORT message 6-31
EMERG POWER RECALL message 6-33
EMERG POWER RUN message 6-33
EMERG POWER SHUTDOWN message 6-33
EMERG PWR NO COMM message 6-33
Emerg. Pwr. Car Selected to Recall output 9-117
Emerg. Pwr. Car Selected to Run output 9-117
Emergency Alarm Acknowledged message 6-30
Emergency Alarm Activated (Alarm button) message 6-30
Emergency Alarm Activated (Car delayed with doors closed)
message 6-30
Emergency Alarm Activated (In-car stop switch) message
6-30
Emergency Alarm Activated (Safety opened) message 6-30
Emergency Alarm Activated message 6-30
Emergency Alarm Deactivated without Acknowledgment
message 6-31
Emergency Alarm Monitoring 9-34
Emergency Brake Board Quick Reference 6-92
Emergency Brake Leg 1 Short Fault message 6-31
Emergency Brake Leg 2 Short Fault message 6-31
Emergency Brake OK open message 6-31
Emergency Brake OK open Off message 6-31
Emergency Brake Test - Unintended Motion 4-49
Index-7