MCi iControl User Manual page 732

Building floor heights 4-2
Counterweight 3-28
Empty and loaded car weights 4-33
ETS and NTS Limit Switches 4-9
Load Weights 4-30
Load weights 9-146
Learning the Safety Configuration 2-46
Level Down Sensor 3-12, 4-5
Level Up Sensor 4-5
Leveling Accuracy specification 11-2
Leveling distance parameter 4-13, 9-130
Leveling Overspeed Test 4-48
Leveling overspeed, Safety parameter 9-148
Leveling sensor indicators 9-10
Leveling speed parameter 4-13, 9-130
Leveling speed, adjusting for final stop 4-27
Light load anti-nuisance 4-30, 9-38
Light Load Antinuisance message 6-53
Light Load Input input 9-108
Light Load output 9-119
Light load threshold 4-31, 4-33, 9-127
LIMIT SW CHKSUM FAULT message 6-53
LIMIT SW LEARN FAULT message 6-53
Limit Switches Checksum Fault message 6-53
Limit Switches Learn Fault message 6-53
Load calibration on message 6-53
Load learn process activated message 6-53
Load learn process deactivated message 6-53
Load Weigher 1-23
Cross Head Deflection 1-23, 9-127
installing 3-19
Isolated Platform 1-23, 9-127
Rope tension sensing 9-127
Load weigher
Crosshead deflection 4-30
Empty load threshold 4-31
Heavy load threshold 4-31
Isolated platform 4-31
Light load threshold 4-31
Overload threshold 4-31
Rope tension 4-30
Load Weigher (Raw) test point, description 11-4
Load Weigher Adjustment 4-30
Load Weigher Balanced test point, description 11-5
Load Weigher Feedback test point, description 11-5
Load weigher installation
EMCO Load Weigher 5-53
load weigher learn procedure 9-146
Load Weigher parameters 9-126
Analog Device Configuration 9-127
Heavy load threshold 9-127
Light load threshold 9-127
Load Weighing Device Type 9-126
Over Load Threshold 9-127
Load Weigher Sensor Adjustment 4-16
Load Weigher Signal test point, description 11-4
Load Weigher. See also MCE Load Weigher
Loading parameters from a Configuration file 8-22
Lobby Call Dwell Time 9-41
Lobby floor 9-37
Index-14 Manual # 42-02-2222
Lobby parking delay 10-21
Lobby peak 10-71
Lobby peak detection parameters 10-15
Lobby Peak Mode message 6-53
Lobby peak mode, selecting 10-15
Lobby peak options 10-16
Lobby peak parameters 10-18
Lobby Shuffle delay 10-21
Local Area Network 8-13
Local car, description of 10-4
Local Dispatcher, description of 10-4
Local Dispatching 10-6–??
Locked, Security status 10-42, 10-45
Locks/Contacts Connections, iBox 6-115, 11-11
Logical Position 9-9
LOSS OF POS/SPD IND message 6-53
Loss of Position or Speed Indicators message 6-53
Low roll jerk parameter 4-13, 9-132
Low speed parameter 9-132
M
MAC ADDRESS ERROR message 6-54
Mac Address Error message 6-54
MAC addresses 9-125
viewing on iBox 7-8
Mach Rm Insp message 6-54
Machine mode 9-9
Machine Rm Inspection message 6-54
Machine Room Heat Detectors Activated message 6-54
Machine Room Heat Detectors Deactivated message 6-54
Machine Room Inspection Disabled message 6-54
Machine Room Inspection Enabled message 6-54
Machine Room Inspection mode 9-7
Machine Room Inspection Operation message 6-54
Machine Room Inspection output 9-119
Machine Room Inspection switch 7-12
Machine Room Inspection, running on 2-54–2-60, ??–2-61,
3-26
Machine Room Preparation
Equipment location 2-4
Machine Room Stop Switch Open message 6-54
Main Fire Recall floor 9-44
Main Floor Smoke input 9-109
MAIN FLOOR SMOKE message 6-55
Main Floor Smoke Sensor Recall message 6-55
Main Processor Board Quick Reference 6-98
Manual configuration serial inputs 10-56
Master Security Override input 9-112
MCE 5-18
MCE job number parameter 10-7
MCE Load Weigher 5-63–5-69
adjusting 5-68
installation 5-63
maintaining 5-68
wiring 5-67
MCE Load Weigher. See also Load Weigher
MCE Loadweigher-Isolated Platform 3-19
MCE System hub 5-10, 5-12
MD, Motor Drive relay indicator 11-12