MCi iControl User Manual page 734

Passenger configuration 9-37–9-43
Passenger mode 9-7
Passenger Operation, Passenger message 6-56
Passing Floor Gong Enabled input 9-109
Passing Floor Gong Enabled output 9-119
Passing Floor Gong output 9-119
Pattern - Common parameters 9-129
Pattern (Command) test point, description 11-5
Pattern (Directional) test point, description 11-5
Pattern (Phase) test point, description 11-5
Pattern (Raw) test point, description 11-5
Pattern (Region) test point, description 11-5
Pattern (Slew Limited) test point, description 11-5
Pattern Filtered test point, description 11-5
Pattern Interpolated test point, description 11-5
Pattern phase 9-10
Pattern profile 9-10
Pattern profile parameters 4-12, 9-128–9-133
Pattern scaling parameter 9-129
Pattern shape preset 9-132
Pedestal Fabrication 3-4
Per floor parking 10-21
Peripheral hub 5-10, 5-11, 5-13, 5-21
Peripheral TCP/IP 5-11
Photo Eye 9-31
Photo Eye Anti-nuisance 9-38
Photo Eye Antinuisance message 6-56
Photo Eye Bypass Timer 9-31
Pick delay 9-26
Pick voltage 2-51, 2-53, 9-25
Pinging 5-24
pinning and unpinning windows in iView 8-33
PM gearless machines, synchronizing with AC drive 2-25,
2-45
Position Bit test point, description 11-6
Position Cartop Offset Fault message 6-56
Position encoder resolution
parameter 9-129
verifying 3-27
Position iBox Connections 6-112, 11-7
Position indicators Binary Outputs 9-121
Position indicators Rotodial Outputs 9-121
Position indicators Single Outputs 9-121
Position Location Error Fault message 6-56
Position Margin 4-55
POSITION QUAD FAULT message 6-57
Position Quadrature Fault message 6-57
Position Quadrature Reversed Fault message 6-57
Position Speed Deviation Fault message 6-57
Position Speed Threshold Fault message 6-57
POSITION SYNC-FLOOR message 6-58
Position Synchronization
Floor 9-130
Preset parameter 9-130
Terminal 9-130
Position Synchronization Fault message 6-58
Position Synchronization parameters 9-130
Position Synchronization Required at Floor message 6-58
Position Synchronization Required at Terminal message 6-58
Position Synchronized at Floor message 6-58
Index-16 Manual # 42-02-2222
Position Synchronized at Terminal message 6-58
POSITION SYNC-TERMINAL message 6-58
POSITN QUAD RVRSD FLT message 6-57
POSITN SPEED DVTN FLT message 6-57
POSTN CARTP OFFST FLT message 6-56
POSTN LCTN ERROR FLT message 6-56
POSTN SPD THRSHLD FLT message 6-57
Power bus verification 5-9
Power line fluctuation 2-4
Power Transfer input 9-109
Power Transfer Input Activated message 6-58
Power Transfer Input Deactivated message 6-58
Power Transfer, POWER TRANSFER message 6-58
Power Up Position Synchronization Required at Terminal
message 6-58
PowerBack R6 Regenerative Drive
Parameters Quick Reference 11-31
Preparing for Final Adjustments 3-28
counterweight balancing 3-29
door operator 3-28
empty car tests 3-31
run testing 3-28, 3-30
Pre-Run Status test point, description 11-6
preset profile parameters 9-132
Pre-start Door Lock Fault message 6-59
Pre-Start Sequence 4-35–4-40
diagrams 4-36
parameters 4-35, 9-88
Pretorque (Raw) test point, description 11-6
Pretorque Command test point, description 11-6
Pretorque Gain, adjusting 4-17
Pretorque option 4-17
Pretorque Position Compensation 4-17
PRI FIRE SWITCH BYP message 6-59
PRI FIRE SWITCH ON message 6-59
Primary Fire Switch BYPASS input 9-109
Primary Fire Switch Bypass message 6-59
Primary Fire Switch OFF input 9-109
Primary Fire Switch ON input 9-109
Primary Fire Switch On message 6-59
Printing screens in iView 8-38
Processed pattern frequency parameter 9-91
programmable inputs 9-106
programmable outputs 9-115
Pulses per foot, Safety parameter 9-148
Q
QPRAM Device Error message 6-59
Quadrature Pulse Indicators 3-12
Quadrature Pulse Sequence 3-27
Quadrature Pulse Voltages 3-27
Quadrature Sensor Adjustment 3-3
R
R DPM OPEN-GS CLOSED message 6-61
R DR CLS FLT REC FAIL message 6-60
R6 Regenerative AC drive parameters 11-31
Rated motor RPM parameter 9-89
Raw pattern frequency parameter 9-91