Tim1 Dma Control Register (Timx_Dcr) - STMicroelectronics RM0365 Reference Manual

RM0365
Bit 10 OSSI: Off-state selection for Idle mode
This bit is used when MOE=0 due to a break event or by a software write, on channels
configured as outputs.
See OC/OCN enable description for more details
enable register
0: When inactive, OC/OCN outputs are disabled (the timer releases the output control which
is taken over by the GPIO logic and which imposes a Hi-Z state).
1: When inactive, OC/OCN outputs are first forced with their inactive level then forced to their
idle level after the deadtime. The timer maintains its control over the output.
Note: This bit can not be modified as soon as the LOCK level 2 has been programmed (LOCK
Bits 9:8 LOCK[1:0]: Lock configuration
These bits offer a write protection against software errors.
00: LOCK OFF - No bit is write protected.
01: LOCK Level 1 = DTG bits in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2
register and BKE/BKP/AOE bits in TIMx_BDTR register can no longer be written.
10: LOCK Level 2 = LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER
register, as long as the related channel is configured in output through the CCxS bits) as well
as OSSR and OSSI bits can no longer be written.
11: LOCK Level 3 = LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in
TIMx_CCMRx registers, as long as the related channel is configured in output through the
CCxS bits) can no longer be written.
Note: The LOCK bits can be written only once after the reset. Once the TIMx_BDTR register
Bits 7:0 DTG[7:0]: Dead-time generator setup
This bit-field defines the duration of the dead-time inserted between the complementary
outputs. DT correspond to this duration.
DTG[7:5]=0xx => DT=DTG[7:0]x t
DTG[7:5]=10x => DT=(64+DTG[5:0])xt
DTG[7:5]=110 => DT=(32+DTG[4:0])xt
DTG[7:5]=111 => DT=(32+DTG[4:0])xt
Example if T
0 to 15875 ns by 125 ns steps,
16 us to 31750 ns by 250 ns steps,
32 us to 63us by 1 us steps,
64 us to 126 us by 2 us steps
Note: This bit-field can not be modified as long as LOCK level 1, 2 or 3 has been programmed
20.4.19

TIM1 DMA control register (TIMx_DCR)

Address offset: 0x48
Reset value: 0x0000
15 14 13
Res. Res. Res.
Bits 15:13 Reserved, must be kept at reset value.
(TIMx_CCER)).
bits in TIMx_BDTR register).
has been written, their content is frozen until the next reset.
=125ns (8MHz), dead-time possible values are:
DTS
(LOCK bits in TIMx_BDTR register).
12 11 10 9
DBL[4:0]
rw rw rw rw
DocID025202 Rev 7
(Section 20.4.9: TIM1 capture/compare
with t =t .
dtg dtg DTS
with T =2xt
dtg dtg
with T =8xt
dtg dtg
with T =16xt
dtg dtg
8 7 6 5
Res. Res. Res.
rw
Advanced-control timers (TIM1)
.
DTS
.
DTS
.
DTS
4 3 2
DBA[4:0]
rw rw rw
1 0
rw rw
542/1080
549