Toshiba e-STUDIO206L Service Manual page 18

6.16 Adjustment of the Finisher (MJ-1101/1107) .................................................................... 6-95
6.16.1 Adjusting the alignment position ...................................................................... 6-95
6.16.2 Adjusting the stapling position ......................................................................... 6-97
6.16.3 B4-size recycled paper mode settings............................................................. 6-99
6.16.4 Adjusting Paper Exit Speed ........................................................................... 6-101
6.17 Adjustment of the Finisher (MJ-1106/1108) .................................................................. 6-108
6.17.1 Adjusting the Alignment Position ................................................................... 6-108
6.17.2 Adjusting the Stapling Position ...................................................................... 6-111
6.17.3 Stapling/folding position adjustment in saddle stitch unit............................... 6-113
6.17.4 Saddle Stitch Skew Adjustment..................................................................... 6-119
6.18 Adjustment of Hole punch unit (MJ-6007)..................................................................... 6-120
6.18.1 Destination setting of hole punch control PC board....................................... 6-120
6.19 Adjustment of Hole punch unit (MJ-6008)..................................................................... 6-121
6.19.1 Sensor output adjustment ............................................................................. 6-121
6.19.2 Registration of the number of punch holes .................................................... 6-124
7. PREVENTIVE MAINTENANCE (PM)............................................................................ 7-1
7.1 General Description .......................................................................................................... 7-1
7.2 PM Display ........................................................................................................................ 7-1
7.2.1 General description............................................................................................ 7-1
7.2.2 PM display conditions ........................................................................................ 7-1
7.2.3 PM display contents........................................................................................... 7-3
7.2.4 Clearing counter ................................................................................................ 7-3
7.3 General Descriptions for PM Procedure ........................................................................... 7-4
7.4 PM Support Mode (6S) ..................................................................................................... 7-5
7.4.1 General description............................................................................................ 7-5
7.4.2 Operational flow and operational screen ........................................................... 7-5
7.4.3 Work flow of parts replacement ....................................................................... 7-10
7.5 EPU Replacement Mode (7S)......................................................................................... 7-11
7.5.1 General description.......................................................................................... 7-11
7.5.2 Operation flow.................................................................................................. 7-11
7.5.3 Counters to be cleared .................................................................................... 7-13
7.5.4 Precautions...................................................................................................... 7-13
7.5.5 To allow the equipment to detect a recycled unit as a new one after replacement
......................................................................................................................... 7-14
7.6 Fuser Unit Status Detection Mode .................................................................................. 7-15
7.6.1 General description.......................................................................................... 7-15
7.6.2 Operational flow............................................................................................... 7-15
7.6.3 Counters to be cleared .................................................................................... 7-15
7.6.4 Precautions...................................................................................................... 7-15
7.7 Preventive Maintenance Checklist .................................................................................. 7-16
7.7.1 Scanner ........................................................................................................... 7-17
7.7.2 Laser optical unit.............................................................................................. 7-18
7.7.3 Paper feeding section ...................................................................................... 7-19
7.7.4 Drum related section........................................................................................ 7-22
7.7.5 Developer section ............................................................................................ 7-24
7.7.6 Fuser unit......................................................................................................... 7-26
7.7.7 Paper exit section / Reverse section ............................................................... 7-28
7.7.8 Automatic duplexing unit.................................................................................. 7-29
7.7.9 PFP (KD-1025) ................................................................................................ 7-30
7.7.10 LCF (KD-1026) ................................................................................................ 7-31
7.7.11 Job separator (MJ-5004) ................................................................................. 7-32
7.7.12 Offset tray (MJ-5005)....................................................................................... 7-33
7.7.13 RADF (MR-3021/3022/3028) ........................................................................... 7-34
7.7.14 Finisher (MJ-1032) .......................................................................................... 7-34
7.7.15 Finisher (MJ-1033) .......................................................................................... 7-35
7.7.16 Finisher (MJ-1101/1107).................................................................................. 7-36
7.7.17 Finisher (MJ-1106/1108).................................................................................. 7-40
7.7.18 Hole punch unit (MJ-6103/6104) ..................................................................... 7-45
e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507
CONTENTS
© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved
8