Toshiba e-STUDIO206L Service Manual page 15

4.12.3 Removing developer material ........................................................................ 4-101
4.12.4 Filling developer unit with developer material................................................ 4-102
4.12.5 EPU memory board (EPU) ............................................................................ 4-102
4.12.6 Auto-toner sensor (S8) .................................................................................. 4-103
4.12.7 Drum thermistor (THMS4) ............................................................................. 4-103
4.12.8 Guide roller / Developer sleeve ..................................................................... 4-104
4.12.9 Mixer .............................................................................................................. 4-108
4.12.10 Replacement of oil seal ................................................................................. 4-110
4.13 FUSER UNIT................................................................................................................. 4-111
4.13.1 Fuser unit....................................................................................................... 4-111
4.13.2 Fuser roller unit / Pressure roller unit............................................................. 4-112
4.13.3 Separation finger ........................................................................................... 4-113
4.13.4 Fuser roller..................................................................................................... 4-114
4.13.5 Heater lamp ................................................................................................... 4-115
4.13.6 Center / Side / Edge thermistor (THMS1/THMS2/THMS3) ........................... 4-117
4.13.7 Fuser center / Fuser front thermostat (THMO1/THMO2)............................... 4-118
4.13.8 Pressure roller ............................................................................................... 4-120
4.13.9 Exit sensor (S9) ............................................................................................. 4-122
4.13.10 Installation of the fuser unit fuse (service part) .............................................. 4-123
4.14 PAPER EXIT SECTION/REVERSE SECTION............................................................. 4-124
4.14.1 Reverse unit (only installed for e-STUDIO356/456/506 / 357/457/507) ........ 4-124
4.14.2 Paper exit unit................................................................................................ 4-125
4.14.3 Exit motor (M10) ............................................................................................ 4-126
4.14.4 Offset gate home position sensor (S24) ........................................................ 4-127
4.14.5 Exit roller........................................................................................................ 4-127
Reverse motor (M14) (only installed for e-STUDIO356/456/506 / 357/457/507) ..
4.14.6
....................................................................................................................... 4-129
4.14.7 Reverse gate solenoid (SOL1) (only installed for e-STUDIO356/456/506 / 357/457/
507)................................................................................................................ 4-130
Reverse sensor (S23) (only installed for e-STUDIO356/456/506 / 357/457/507) .
4.14.8
....................................................................................................................... 4-131
4.14.9 Offset gate motor (M13) (only installed for e-STUDIO356/456/506 / 357/457/507)
....................................................................................................................... 4-132
4.14.10 Reverse roller (only installed for e-STUDIO356/456/506 / 357/457/507) ...... 4-132
4.14.11 Upper transport roller (only installed for e-STUDIO356/456/506 / 357/457/507) ..
....................................................................................................................... 4-133
4.15 AUTOMATIC DUPLEXING UNIT (ADU)....................................................................... 4-134
4.15.1 Automatic Duplexing Unit (ADU) ................................................................... 4-134
4.15.2 ADU entrance sensor (S11)........................................................................... 4-135
4.15.3 ADU exit sensor (S10) ................................................................................... 4-136
4.15.4 ADU motor (M5)............................................................................................. 4-137
4.15.5 ADU opening / closing switch (SW5) ............................................................. 4-138
4.15.6 ADU clutch (CLT1)......................................................................................... 4-139
4.15.7 ADU lower transport roller ............................................................................. 4-141
4.15.8 ADU upper transport roller............................................................................. 4-141
4.16 Installation and Replacement of Options ...................................................................... 4-143
4.16.1 MR-3021/3022/3028 (Reversing Automatic Document Feeder (RADF)) ...... 4-143
4.16.2 KD-1025 (Paper Feed Pedestal (PFP)) ......................................................... 4-145
4.16.3 KD-1026 (Large Capacity Feeder (LCF)) ...................................................... 4-147
4.16.4 MJ-1032 (Finisher)......................................................................................... 4-149
4.16.5 MJ-1033 (Finisher)......................................................................................... 4-152
4.16.6 MJ-1101/1107 (Finisher)................................................................................ 4-155
4.16.7 MJ-1106/1108 (Finisher)................................................................................ 4-156
4.16.8 KN-2520 (Bridge unit) .................................................................................... 4-158
4.16.9 MJ-5004 (Job separator) (e-STUDIO206L/256/306 / 207L/257/307) ............ 4-160
4.16.10 MJ-5005 (Offset tray) (e-STUDIO206L/256/306 / 207L/257/307).................. 4-162
4.16.11 MJ-5006 (Job separator) (e-STUDIO356/456/506 / 357/457/507) ................ 4-163
4.17 Damp Heater Kit (MF-4550U/E) Installation Procedure ................................................ 4-165
© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507
5
CONTENTS