N7: Simple Vector Tuning; N8: Pm Motor Control Tuning - Omron Q2A Series Technical Manual

11.10 n: SPECIAL
◆

n7: SIMPLE VECTOR TUNING

No.
Name
(Hex.)
n7-01 LoFreq Damping Gain
(3111)
Expert
n7-05 TrqCtrl Response Gain
(3115)
Expert
n7-07 Speed Calc.Gain1
(3117)
Expert
n7-08 Speed Calc.Gain2
(3118)
Expert
n7-10 Pull-in SwitchSpeed
(311A)
Expert
n7-17 Resist.Temp.
Compensation
(3122)
◆

n8: PM MOTOR CONTROL TUNING

No.
Name
(Hex.)
n8-01 PolPos Detection
Current
(0540)
Expert
n8-02 Pole Align Current Level
(0541)
Expert
n8-03 Current Start Time
(0542)
n8-04 Pole Align Time
(0543)
Expert
n8-11 Observ.Calc Gain2
(054A)
n8-14 Polar Comp Gain3
(054D)
Expert
n8-15 Polar Comp Gain4
(054E)
Expert
n8-21 Mot Back-EMF (Ke)
Gain
(0554)
Expert
n8-35 InitRotorPos Selection
(0562)
n8-36 HFI Signal Frequency
(0563)
n8-37 HFI Voltage Amplitude
Level
(0564)
Expert
460
Description
V/f CL-V/f OLV CLV AOLV
Sets the oscillation suppression gain for the low speed range.
V/f CL-V/f OLV CLV AOLV
Sets the response gain related to changes in the load.
V/f CL-V/f OLV CLV AOLV
Sets the speed calculation gain during usual operation.
Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the speed calculation gain during a speed search.
V/f CL-V/f OLV CLV AOLV
Sets a speed range proportional to the rated frequency that enables pull-in current
commands.
V/f CL-V/f OLV CLV AOLV
Sets the function to adjust for changes in the motor resistance value caused by changes
in the temperature.
1 : Invalid
2 : Valid (1 Time)
3 : Valid (Every Time)
Description
V/f CL-V/f OLV CLV AOLV
Sets the Initial Rotor Position Estimated Current as a percentage where E5-03 [PM Mot
Rated Current (FLA)] = 100%. Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the current at the time of polar attraction as a percentage where motor rated current
= 100%. Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the length of the Current Starting Time, which is used for Z Pulse Offset Tuning.
Usually it is not necessary to change this parameter.
V/f CL-V/f OLV CLV AOLV
Sets the length of the Polar Attraction Time, which is used for Z Pulse Offset Tuning.
Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the gain for speed estimation. Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the gain for speed estimation. Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the gain for speed estimation. Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the gain for speed estimation. Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets how the drive detects the position of the rotor at start.
Note:
When you use an SPM motor, set this parameter to 1.
1 : Pull-In
2 : HiFreq Injection
3 : Pulse Injection
V/f CL-V/f OLV CLV AOLV
Sets the injection frequency for high frequency injection.
V/f CL-V/f OLV CLV AOLV
Sets the high frequency injection amplitude as a percentage where 400 V = 100% for a
400 V class drives. Usually it is not necessary to change this setting.
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
Default
Ref.
(Range)
1.0 796
(0.1 - 10.0)
1.00 796
(0.10 - 10.00)
15.0 Hz 796
(1.0 - 50.0 Hz)
25.0 Hz 796
(1.0 - 50.0 Hz)
10.0% 796
(0.0 - 100.0%)
2 796
(1 - 3)
Default
Ref.
(Range)
50% 797
(0 - 100%)
80% 797
(0 - 150%)
1.5 s 797
(1.5 - 5.0 s)
1.5 s 797
(1.5 - 5.0 s)
Determined by n8-72 798
(0.0 - 1000.0)
2.000 798
(0.000 - 20.000)
2.000 798
(0.000 - 20.000)
0.90 798
(0.80 - 1.00)
Determined by A1-02 798
(1 - 3)
500 Hz 798
(200 - 5000 Hz)
20.0% 799
(0.0 - 50.0%)