Omron Q2A Series Technical Manual page 424

11.7 F: OPTIONS
No.
Name
(Hex.)
F6-07 Multi-Ref@NetRef/
ComRef
(03A8)
F6-08 Comm Par
RST@Initialize
(036A)
F6-10 CCLink Node Address
(03B6)
F6-11 CCLink Comm Speed
(03B7)
F6-14 BUS Err. AutoReset
(03BB)
F6-16 Gateway Mode
(0B8A)
F6-20 MLII Address
(036B)
F6-21 MLII Frame Size
(036C)
F6-22 MLII Link Speed
(036D)
F6-23 MLII Mon Sel (E)
(036E)
F6-24 MLII Mon Sel (F)
(036F)
424
Description
V/f CL-V/f OLV CLV AOLV
Sets the function that enables and disables the multi-step speed reference when the
frequency reference source is NetRef or ComRef (communication option card or
Modbus communications).
0 : Disable MultiStep References
1 : Enable MultiStep References
V/f CL-V/f OLV CLV AOLV
Sets the function to initialize F6-xx and F7-xx parameters when the drive is initialized
with A1-03 [Init Parameters].
0 : Retain Pars - No Reset
1 : Factory Default - Reset
V/f CL-V/f OLV CLV AOLV
Sets the node address for CC-Link communication. Restart the drive after changing this
setting.
Note:
Be sure to set a node address that is different than all other node addresses. Do not
set this parameter to 0. Incorrect parameter settings will cause AEr [Station Address
Setting Error] errors and the L.ERR LED on the option will come on.
V/f CL-V/f OLV CLV AOLV
Sets the communication speed for CC-Link communication. Restart the drive after you
change this setting.
0 : 156 kbps
1 : 625 kbps
2 : 2.5 Mbps
3 : 5 Mbps
4 : 10 Mbps
V/f CL-V/f OLV CLV AOLV
Sets the automatic reset function for bUS [Option Communication Errors].
0 : Disabled
1 : Enabled
V/f CL-V/f OLV CLV AOLV
Sets the gateway mode operation and the number of connected slave drives.
0 : Disabled
1 : 1 Slave Drive
2 : 2 Slave Drives
3 : 3 Slave Drives
4 : 4 Slave Drives
V/f CL-V/f OLV CLV AOLV
Sets the station address for MECHATROLINK communication. Restart the drive after
changing this setting.
Note:
• The setting range changes if using MECHATROLINK-II or MECHATROLINK-
III:
–MECHATROLINK-II (SI-T3) range: 20 - 3F
–MECHATROLINK-III (SI-ET3) range: 03 - EF
• Be sure to set a node address that is different than all other node addresses.
Incorrect parameter settings will cause AEr [Station Address Setting Error] errors
and the L.ERR LED on the option will come on.
• The drive detects AEr errors when the station address is 20 or 3F.
V/f CL-V/f OLV CLV AOLV
Sets the frame size for MECHATROLINK communication. Restart the drive after you
change this setting.
0 : 32-byte
1 : 17-byte
V/f CL-V/f OLV CLV AOLV
Sets the communications speed for MECHATROLINK-II. Restart the drive after you
change this setting.
Note:
This parameter is only available with the MECHATROLINK-II option.
0 : 10 Mbps
1 : 4 Mbps
V/f CL-V/f OLV CLV AOLV
Sets the Modbus register used for the monitor functions of INV_CTL (drive operation
control command) and INV_I/O (drive I/O control command). Restart the drive after
you change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the Modbus register used for the monitor functions of INV_CTL (drive operation
control command) and INV_I/O (drive I/O control command). Restart the drive after
you change this setting.
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
Default
Ref.
(Range)
0 648
(0, 1)
0 649
(0, 1)
0 649
(0 - 64)
0 649
(0 - 4)
0 649
(0, 1)
0 650
(0 - 4)
0021h 652
(MECHATROLINK-
II：0020h - 003Fh，
MECHATROLINK-
III：0003h - 00EFh)
0 653
(0, 1)
0 653
(0, 1)
0000h 653
(0000h - FFFFh)
0000h 653
(0000h - FFFFh)